[U-Boot] [PATCH 26/26] configs: mtmips: add necessary drivers for mtmips boards

[Weijie Gao]

On Wed, 2019-08-28 at 15:40 +0200, Stefan Roese wrote:
> On 28.08.19 15:35, Daniel Schwierzeck wrote:
> > 
> > 
> > Am 28.08.19 um 08:38 schrieb Weijie Gao:
> >> This patch adds pinctrl driver, clock gate driver and reset controller
> >> support for defconfig files of mtmips boards.
> >>
> >> Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
> >> ---
> >>   configs/gardena-smart-gateway-mt7688_defconfig | 6 ++++++
> >>   configs/linkit-smart-7688_defconfig            | 6 ++++++
> >>   2 files changed, 12 insertions(+)
> >>
> >> diff --git a/configs/gardena-smart-gateway-mt7688_defconfig b/configs/gardena-smart-gateway-mt7688_defconfig
> >> index 1e270cb61d..83e793042a 100644
> >> --- a/configs/gardena-smart-gateway-mt7688_defconfig
> >> +++ b/configs/gardena-smart-gateway-mt7688_defconfig
> >> @@ -49,6 +49,7 @@ CONFIG_NET_RANDOM_ETHADDR=y
> >>   CONFIG_HAVE_BLOCK_DEVICE=y
> >>   CONFIG_BOOTCOUNT_LIMIT=y
> >>   CONFIG_CLK=y
> >> +CONFIG_CLK_MTMIPS_GATE=y
> >>   CONFIG_LED=y
> >>   CONFIG_LED_BLINK=y
> >>   CONFIG_LED_GPIO=y
> >> @@ -67,10 +68,15 @@ CONFIG_PHYLIB=y
> >>   CONFIG_PHY_FIXED=y
> >>   CONFIG_MT7628_ETH=y
> >>   CONFIG_PHY=y
> >> +CONFIG_PINCTRL=y
> >> +CONFIG_PINMUX=y
> >> +CONFIG_PINCONF=y
> >> +CONFIG_PINCTRL_MT7628=y
> >>   CONFIG_POWER_DOMAIN=y
> >>   CONFIG_RAM=y
> >>   CONFIG_DM_RESET=y
> >>   # CONFIG_SPL_SERIAL_PRESENT is not set
> >> +CONFIG_RESET_MTMIPS=y
> > 
> > if the SoC only works with those drivers enabled, you should consider to
> > select all according Kconfig symbols in arch/mips/mach-mtmips/Kconfig so
> > an user can't configure a non-working board config by mistake.
> 
> I agree. Please move those selections to Kconfig (select XXX).
> 
> And please re-think about using the generic drivers for pinctrl and clock
> (as also remarked by Daniel).
> 
> Thanks,
> Stefan
> 
> > 
> >>   CONFIG_MTK_SERIAL=y
> >>   CONFIG_SPI=y
> >>   CONFIG_MT7621_SPI=y
> >> diff --git a/configs/linkit-smart-7688_defconfig b/configs/linkit-smart-7688_defconfig
> >> index 743cc48166..13f5cf8a21 100644
> >> --- a/configs/linkit-smart-7688_defconfig
> >> +++ b/configs/linkit-smart-7688_defconfig
> >> @@ -40,6 +40,7 @@ CONFIG_NET_RANDOM_ETHADDR=y
> >>   # CONFIG_DM_DEVICE_REMOVE is not set
> >>   CONFIG_BLK=y
> >>   CONFIG_CLK=y
> >> +CONFIG_CLK_MTMIPS_GATE=y
> >>   CONFIG_LED=y
> >>   CONFIG_LED_BLINK=y
> >>   CONFIG_LED_GPIO=y
> >> @@ -55,10 +56,15 @@ CONFIG_PHY_FIXED=y
> >>   CONFIG_MT7628_ETH=y
> >>   CONFIG_PHY=y
> >>   CONFIG_MT76X8_USB_PHY=y
> >> +CONFIG_PINCTRL=y
> >> +CONFIG_PINMUX=y
> >> +CONFIG_PINCONF=y
> >> +CONFIG_PINCTRL_MT7628=y
> >>   CONFIG_POWER_DOMAIN=y
> >>   CONFIG_RAM=y
> >>   CONFIG_DM_RESET=y
> >>   # CONFIG_SPL_SERIAL_PRESENT is not set
> >> +CONFIG_RESET_MTMIPS=y
> >>   CONFIG_MTK_SERIAL=y
> >>   CONFIG_SPI=y
> >>   CONFIG_MT7621_SPI=y
> >>
> > 
> 
> Viele Grüße,
> Stefan
> 

I'll move them to mach-mtmips/Kconfig.