[U-Boot] [PATCH 3/4] net/ftgmac100: Add NC-SI mode support

[Samuel Mendoza-Jonas]

Update the ftgmac100 driver to support NC-SI instead of an mdio phy
where available. This is a common setup for Aspeed AST2x00 platforms.

NC-SI mode is determined from the device-tree if either phy-mode sets it
or the use-ncsi property exists. If set then normal mdio setup is
skipped in favour of the NC-SI phy.

Signed-off-by: Samuel Mendoza-Jonas <sam at mendozajonas.com>
---
 drivers/net/ftgmac100.c | 39 +++++++++++++++++++++++++++++----------
 1 file changed, 29 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ftgmac100.c b/drivers/net/ftgmac100.c
index 92c38a81bd..c0100e91c7 100644
--- a/drivers/net/ftgmac100.c
+++ b/drivers/net/ftgmac100.c
@@ -18,6 +18,7 @@
 #include <wait_bit.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
+#include <net/ncsi.h>
 
 #include "ftgmac100.h"
 
@@ -81,6 +82,7 @@ struct ftgmac100_data {
 	struct mii_dev *bus;
 	u32 phy_mode;
 	u32 max_speed;
+	bool ncsi_mode;
 
 	struct clk_bulk clks;
 
@@ -181,7 +183,7 @@ static int ftgmac100_phy_adjust_link(struct ftgmac100_data *priv)
 	struct phy_device *phydev = priv->phydev;
 	u32 maccr;
 
-	if (!phydev->link) {
+	if (!phydev->link && !priv->ncsi_mode) {
 		dev_err(phydev->dev, "No link\n");
 		return -EREMOTEIO;
 	}
@@ -217,7 +219,8 @@ static int ftgmac100_phy_init(struct udevice *dev)
 	if (!phydev)
 		return -ENODEV;
 
-	phydev->supported &= PHY_GBIT_FEATURES;
+	if (!priv->ncsi_mode)
+		phydev->supported &= PHY_GBIT_FEATURES;
 	if (priv->max_speed) {
 		ret = phy_set_supported(phydev, priv->max_speed);
 		if (ret)
@@ -275,7 +278,8 @@ static void ftgmac100_stop(struct udevice *dev)
 
 	writel(0, &ftgmac100->maccr);
 
-	phy_shutdown(priv->phydev);
+	if (!priv->ncsi_mode)
+		phy_shutdown(priv->phydev);
 }
 
 static int ftgmac100_start(struct udevice *dev)
@@ -513,6 +517,7 @@ static int ftgmac100_ofdata_to_platdata(struct udevice *dev)
 	pdata->iobase = devfdt_get_addr(dev);
 	pdata->phy_interface = -1;
 	phy_mode = dev_read_string(dev, "phy-mode");
+
 	if (phy_mode)
 		pdata->phy_interface = phy_get_interface_by_name(phy_mode);
 	if (pdata->phy_interface == -1) {
@@ -537,8 +542,13 @@ static int ftgmac100_probe(struct udevice *dev)
 {
 	struct eth_pdata *pdata = dev_get_platdata(dev);
 	struct ftgmac100_data *priv = dev_get_priv(dev);
+	const char *phy_mode;
 	int ret;
 
+	phy_mode = dev_read_string(dev, "phy-mode");
+	priv->ncsi_mode = dev_read_bool(dev, "use-ncsi") ||
+		(phy_mode && strcmp(phy_mode, "NC-SI") == 0);
+
 	priv->iobase = (struct ftgmac100 *)pdata->iobase;
 	priv->phy_mode = pdata->phy_interface;
 	priv->max_speed = pdata->max_speed;
@@ -548,10 +558,15 @@ static int ftgmac100_probe(struct udevice *dev)
 	if (ret)
 		goto out;
 
-	ret = ftgmac100_mdio_init(dev);
-	if (ret) {
-		dev_err(dev, "Failed to initialize mdiobus: %d\n", ret);
-		goto out;
+	if (priv->ncsi_mode) {
+		printf("%s - NCSI detected\n", __func__);
+	} else {
+		ret = ftgmac100_mdio_init(dev);
+		if (ret) {
+			dev_err(dev, "Failed to initialize mdiobus: %d\n", ret);
+			goto out;
+		}
+
 	}
 
 	ret = ftgmac100_phy_init(dev);
@@ -571,9 +586,13 @@ static int ftgmac100_remove(struct udevice *dev)
 {
 	struct ftgmac100_data *priv = dev_get_priv(dev);
 
-	free(priv->phydev);
-	mdio_unregister(priv->bus);
-	mdio_free(priv->bus);
+	if (!priv->ncsi_mode) {
+		free(priv->phydev);
+		mdio_unregister(priv->bus);
+		mdio_free(priv->bus);
+	} else {
+		free(priv->phydev);
+	}
 	clk_release_bulk(&priv->clks);
 
 	return 0;
-- 
2.21.0