[U-Boot] [PATCH v8 2/3] rockchip: rk3399: Add Rockpro64 board support
Paul Kocialkowski
paul.kocialkowski at bootlin.com
Thu Jun 6 09:55:09 UTC 2019
Hi,
On Sat, 2019-06-01 at 10:41 +0800, Kever Yang wrote:
>
> On 05/29/2019 04:09 PM, Kever Yang wrote:
> > On 05/17/2019 06:29 PM, Jagan Teki wrote:
> > > Add initial support for Rockpro64 board.
> > >
> > > Specification
> > > - Rockchip RK3399
> > > - 2/4GB Dual-Channel LPDDR3
> > > - SD card slot
> > > - eMMC socket
> > > - 128Mb SPI Flash
> > > - Gigabit ethernet
> > > - PCIe 4X slot
> > > - WiFI/BT module socket
> > > - HDMI In/Out, DP, MIPI DSI/CSI, eDP
> > > - USB 3.0, 2.0
> > > - USB Type C power and data
> > > - GPIO expansion ports
> > > - DC 12V/2A
> > >
> > > Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
> > > "arm64: dts: rockchip: rockpro64 dts add usb regulator"
> > > (sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
> > >
> > > 'Akash' has sent an initial patch before, so I keep him as board
> > > maintainer and I'm co-maintainer based on our conversation.
> > >
> > > Signed-off-by: Akash Gajjar <akash at openedev.com>
> > > Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> > Reviewed-by: Kever Yang <kever.yang at rock-chips.com>
>
> Applied to u-boot-rockchip/master, thanks!
I'm very surprised to read this. Is SPL support part of this version or
was it disabled? I thought there was an agreement to not merge the
patches until the SPL issue is resolved.
Can you explain what happened?
Cheers,
Paul
> > Thanks,
> > - Kever
> >
> > > ---
> > > Changes for v8:
> > > - Add TPL support
> > > - Now the bootchain is
> > > rkbin (TPL) -> SPL -> U-Boot proper
> > >
> > > arch/arm/dts/Makefile | 1 +
> > > arch/arm/dts/rk3399-rockpro64-u-boot.dtsi | 6 +
> > > arch/arm/dts/rk3399-rockpro64.dts | 712 ++++++++++++++++++++++
> > > board/rockchip/evb_rk3399/MAINTAINERS | 7 +
> > > configs/rockpro64-rk3399_defconfig | 60 ++
> > > 5 files changed, 786 insertions(+)
> > > create mode 100644 arch/arm/dts/rk3399-rockpro64-u-boot.dtsi
> > > create mode 100644 arch/arm/dts/rk3399-rockpro64.dts
> > > create mode 100644 configs/rockpro64-rk3399_defconfig
> > >
> > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > > index 529c506b4d..8522f01aca 100644
> > > --- a/arch/arm/dts/Makefile
> > > +++ b/arch/arm/dts/Makefile
> > > @@ -114,6 +114,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
> > > rk3399-puma-ddr1600.dtb \
> > > rk3399-puma-ddr1866.dtb \
> > > rk3399-rock960.dtb \
> > > + rk3399-rockpro64.dtb
> > >
> > > dtb-$(CONFIG_ROCKCHIP_RV1108) += \
> > > rv1108-elgin-r1.dtb \
> > > diff --git a/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi b/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi
> > > new file mode 100644
> > > index 0000000000..7bddc3acdb
> > > --- /dev/null
> > > +++ b/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi
> > > @@ -0,0 +1,6 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright (C) 2019 Jagan Teki <jagan at amarulasolutions.com>
> > > + */
> > > +
> > > +#include "rk3399-u-boot.dtsi"
> > > diff --git a/arch/arm/dts/rk3399-rockpro64.dts b/arch/arm/dts/rk3399-rockpro64.dts
> > > new file mode 100644
> > > index 0000000000..1f2394e058
> > > --- /dev/null
> > > +++ b/arch/arm/dts/rk3399-rockpro64.dts
> > > @@ -0,0 +1,712 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > > +/*
> > > + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> > > + * Copyright (c) 2018 Akash Gajjar <Akash_Gajjar at mentor.com>
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include <dt-bindings/input/linux-event-codes.h>
> > > +#include <dt-bindings/pwm/pwm.h>
> > > +#include "rk3399.dtsi"
> > > +#include "rk3399-opp.dtsi"
> > > +
> > > +/ {
> > > + model = "Pine64 RockPro64";
> > > + compatible = "pine64,rockpro64", "rockchip,rk3399";
> > > +
> > > + chosen {
> > > + stdout-path = "serial2:1500000n8";
> > > + };
> > > +
> > > + clkin_gmac: external-gmac-clock {
> > > + compatible = "fixed-clock";
> > > + clock-frequency = <125000000>;
> > > + clock-output-names = "clkin_gmac";
> > > + #clock-cells = <0>;
> > > + };
> > > +
> > > + gpio-keys {
> > > + compatible = "gpio-keys";
> > > + autorepeat;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pwrbtn>;
> > > +
> > > + power {
> > > + debounce-interval = <100>;
> > > + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> > > + label = "GPIO Key Power";
> > > + linux,code = <KEY_POWER>;
> > > + wakeup-source;
> > > + };
> > > + };
> > > +
> > > + leds {
> > > + compatible = "gpio-leds";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&work_led_gpio>, <&diy_led_gpio>;
> > > +
> > > + work-led {
> > > + label = "work";
> > > + default-state = "on";
> > > + gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> > > + };
> > > +
> > > + diy-led {
> > > + label = "diy";
> > > + default-state = "off";
> > > + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> > > + };
> > > + };
> > > +
> > > + sdio_pwrseq: sdio-pwrseq {
> > > + compatible = "mmc-pwrseq-simple";
> > > + clocks = <&rk808 1>;
> > > + clock-names = "ext_clock";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&wifi_enable_h>;
> > > +
> > > + /*
> > > + * On the module itself this is one of these (depending
> > > + * on the actual card populated):
> > > + * - SDIO_RESET_L_WL_REG_ON
> > > + * - PDN (power down when low)
> > > + */
> > > + reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> > > + };
> > > +
> > > + vcc12v_dcin: vcc12v-dcin {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc12v_dcin";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <12000000>;
> > > + regulator-max-microvolt = <12000000>;
> > > + };
> > > +
> > > + /* switched by pmic_sleep */
> > > + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc1v8_s3";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + vin-supply = <&vcc_1v8>;
> > > + };
> > > +
> > > + vcc3v3_pcie: vcc3v3-pcie-regulator {
> > > + compatible = "regulator-fixed";
> > > + enable-active-high;
> > > + gpio = <&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pcie_pwr_en>;
> > > + regulator-name = "vcc3v3_pcie";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + vin-supply = <&vcc12v_dcin>;
> > > + };
> > > +
> > > + vcc3v3_sys: vcc3v3-sys {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc3v3_sys";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + vin-supply = <&vcc5v0_sys>;
> > > + };
> > > +
> > > + /* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */
> > > + vcc5v0_host: vcc5v0-host-regulator {
> > > + compatible = "regulator-fixed";
> > > + enable-active-high;
> > > + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&vcc5v0_host_en>;
> > > + regulator-name = "vcc5v0_host";
> > > + regulator-always-on;
> > > + vin-supply = <&vcc5v0_usb>;
> > > + };
> > > +
> > > + vcc5v0_typec: vcc5v0-typec-regulator {
> > > + compatible = "regulator-fixed";
> > > + enable-active-high;
> > > + gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&vcc5v0_typec_en>;
> > > + regulator-name = "vcc5v0_typec";
> > > + regulator-always-on;
> > > + vin-supply = <&vcc5v0_usb>;
> > > + };
> > > +
> > > + vcc5v0_sys: vcc5v0-sys {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc5v0_sys";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <5000000>;
> > > + regulator-max-microvolt = <5000000>;
> > > + vin-supply = <&vcc12v_dcin>;
> > > + };
> > > +
> > > + vcc5v0_usb: vcc5v0-usb {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc5v0_usb";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <5000000>;
> > > + regulator-max-microvolt = <5000000>;
> > > + vin-supply = <&vcc12v_dcin>;
> > > + };
> > > +
> > > + vdd_log: vdd-log {
> > > + compatible = "pwm-regulator";
> > > + pwms = <&pwm2 0 25000 1>;
> > > + regulator-name = "vdd_log";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <800000>;
> > > + regulator-max-microvolt = <1400000>;
> > > + vin-supply = <&vcc5v0_sys>;
> > > + };
> > > +};
> > > +
> > > +&cpu_l0 {
> > > + cpu-supply = <&vdd_cpu_l>;
> > > +};
> > > +
> > > +&cpu_l1 {
> > > + cpu-supply = <&vdd_cpu_l>;
> > > +};
> > > +
> > > +&cpu_l2 {
> > > + cpu-supply = <&vdd_cpu_l>;
> > > +};
> > > +
> > > +&cpu_l3 {
> > > + cpu-supply = <&vdd_cpu_l>;
> > > +};
> > > +
> > > +&cpu_b0 {
> > > + cpu-supply = <&vdd_cpu_b>;
> > > +};
> > > +
> > > +&cpu_b1 {
> > > + cpu-supply = <&vdd_cpu_b>;
> > > +};
> > > +
> > > +&emmc_phy {
> > > + status = "okay";
> > > +};
> > > +
> > > +&gmac {
> > > + assigned-clocks = <&cru SCLK_RMII_SRC>;
> > > + assigned-clock-parents = <&clkin_gmac>;
> > > + clock_in_out = "input";
> > > + phy-supply = <&vcc_lan>;
> > > + phy-mode = "rgmii";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&rgmii_pins>;
> > > + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
> > > + snps,reset-active-low;
> > > + snps,reset-delays-us = <0 10000 50000>;
> > > + tx_delay = <0x28>;
> > > + rx_delay = <0x11>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&hdmi {
> > > + ddc-i2c-bus = <&i2c3>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&hdmi_cec>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&gpu {
> > > + mali-supply = <&vdd_gpu>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2c0 {
> > > + clock-frequency = <400000>;
> > > + i2c-scl-rising-time-ns = <168>;
> > > + i2c-scl-falling-time-ns = <4>;
> > > + status = "okay";
> > > +
> > > + rk808: pmic at 1b {
> > > + compatible = "rockchip,rk808";
> > > + reg = <0x1b>;
> > > + interrupt-parent = <&gpio1>;
> > > + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> > > + #clock-cells = <1>;
> > > + clock-output-names = "xin32k", "rk808-clkout2";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pmic_int_l>;
> > > + rockchip,system-power-controller;
> > > + wakeup-source;
> > > +
> > > + vcc1-supply = <&vcc5v0_sys>;
> > > + vcc2-supply = <&vcc5v0_sys>;
> > > + vcc3-supply = <&vcc5v0_sys>;
> > > + vcc4-supply = <&vcc5v0_sys>;
> > > + vcc6-supply = <&vcc5v0_sys>;
> > > + vcc7-supply = <&vcc5v0_sys>;
> > > + vcc8-supply = <&vcc3v3_sys>;
> > > + vcc9-supply = <&vcc5v0_sys>;
> > > + vcc10-supply = <&vcc5v0_sys>;
> > > + vcc11-supply = <&vcc5v0_sys>;
> > > + vcc12-supply = <&vcc3v3_sys>;
> > > + vddio-supply = <&vcca_1v8>;
> > > +
> > > + regulators {
> > > + vdd_center: DCDC_REG1 {
> > > + regulator-name = "vdd_center";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <750000>;
> > > + regulator-max-microvolt = <1350000>;
> > > + regulator-ramp-delay = <6001>;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vdd_cpu_l: DCDC_REG2 {
> > > + regulator-name = "vdd_cpu_l";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <750000>;
> > > + regulator-max-microvolt = <1350000>;
> > > + regulator-ramp-delay = <6001>;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcc_ddr: DCDC_REG3 {
> > > + regulator-name = "vcc_ddr";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-state-mem {
> > > + regulator-on-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcc_1v8: DCDC_REG4 {
> > > + regulator-name = "vcc_1v8";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-state-mem {
> > > + regulator-on-in-suspend;
> > > + regulator-suspend-microvolt = <1800000>;
> > > + };
> > > + };
> > > +
> > > + vcc1v8_dvp: LDO_REG1 {
> > > + regulator-name = "vcc1v8_dvp";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcc3v0_touch: LDO_REG2 {
> > > + regulator-name = "vcc3v0_touch";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <3000000>;
> > > + regulator-max-microvolt = <3000000>;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcca_1v8: LDO_REG3 {
> > > + regulator-name = "vcca_1v8";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-state-mem {
> > > + regulator-on-in-suspend;
> > > + regulator-suspend-microvolt = <1800000>;
> > > + };
> > > + };
> > > +
> > > + vcc_sdio: LDO_REG4 {
> > > + regulator-name = "vcc_sdio";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <3000000>;
> > > + regulator-state-mem {
> > > + regulator-on-in-suspend;
> > > + regulator-suspend-microvolt = <3000000>;
> > > + };
> > > + };
> > > +
> > > + vcca3v0_codec: LDO_REG5 {
> > > + regulator-name = "vcca3v0_codec";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <3000000>;
> > > + regulator-max-microvolt = <3000000>;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcc_1v5: LDO_REG6 {
> > > + regulator-name = "vcc_1v5";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1500000>;
> > > + regulator-max-microvolt = <1500000>;
> > > + regulator-state-mem {
> > > + regulator-on-in-suspend;
> > > + regulator-suspend-microvolt = <1500000>;
> > > + };
> > > + };
> > > +
> > > + vcca1v8_codec: LDO_REG7 {
> > > + regulator-name = "vcca1v8_codec";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcc_3v0: LDO_REG8 {
> > > + regulator-name = "vcc_3v0";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-min-microvolt = <3000000>;
> > > + regulator-max-microvolt = <3000000>;
> > > + regulator-state-mem {
> > > + regulator-on-in-suspend;
> > > + regulator-suspend-microvolt = <3000000>;
> > > + };
> > > + };
> > > +
> > > + vcc3v3_s3: vcc_lan: SWITCH_REG1 {
> > > + regulator-name = "vcc3v3_s3";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vcc3v3_s0: SWITCH_REG2 {
> > > + regulator-name = "vcc3v3_s0";
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > + };
> > > + };
> > > +
> > > + vdd_cpu_b: regulator at 40 {
> > > + compatible = "silergy,syr827";
> > > + reg = <0x40>;
> > > + fcs,suspend-voltage-selector = <1>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&vsel1_gpio>;
> > > + regulator-name = "vdd_cpu_b";
> > > + regulator-min-microvolt = <712500>;
> > > + regulator-max-microvolt = <1500000>;
> > > + regulator-ramp-delay = <1000>;
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + vin-supply = <&vcc5v0_sys>;
> > > +
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +
> > > + vdd_gpu: regulator at 41 {
> > > + compatible = "silergy,syr828";
> > > + reg = <0x41>;
> > > + fcs,suspend-voltage-selector = <1>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&vsel2_gpio>;
> > > + regulator-name = "vdd_gpu";
> > > + regulator-min-microvolt = <712500>;
> > > + regulator-max-microvolt = <1500000>;
> > > + regulator-ramp-delay = <1000>;
> > > + regulator-always-on;
> > > + regulator-boot-on;
> > > + vin-supply = <&vcc5v0_sys>;
> > > +
> > > + regulator-state-mem {
> > > + regulator-off-in-suspend;
> > > + };
> > > + };
> > > +};
> > > +
> > > +&i2c1 {
> > > + i2c-scl-rising-time-ns = <300>;
> > > + i2c-scl-falling-time-ns = <15>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2c3 {
> > > + i2c-scl-rising-time-ns = <450>;
> > > + i2c-scl-falling-time-ns = <15>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2c4 {
> > > + i2c-scl-rising-time-ns = <600>;
> > > + i2c-scl-falling-time-ns = <20>;
> > > + status = "okay";
> > > +
> > > + fusb0: typec-portc at 22 {
> > > + compatible = "fcs,fusb302";
> > > + reg = <0x22>;
> > > + interrupt-parent = <&gpio1>;
> > > + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&fusb0_int>;
> > > + vbus-supply = <&vcc5v0_typec>;
> > > + status = "okay";
> > > + };
> > > +};
> > > +
> > > +&i2s0 {
> > > + rockchip,playback-channels = <8>;
> > > + rockchip,capture-channels = <8>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2s1 {
> > > + rockchip,playback-channels = <2>;
> > > + rockchip,capture-channels = <2>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2s2 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&io_domains {
> > > + status = "okay";
> > > +
> > > + bt656-supply = <&vcc1v8_dvp>;
> > > + audio-supply = <&vcca1v8_codec>;
> > > + sdmmc-supply = <&vcc_sdio>;
> > > + gpio1830-supply = <&vcc_3v0>;
> > > +};
> > > +
> > > +&pmu_io_domains {
> > > + pmu1830-supply = <&vcc_3v0>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&pinctrl {
> > > + buttons {
> > > + pwrbtn: pwrbtn {
> > > + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> > > + };
> > > + };
> > > +
> > > + fusb302x {
> > > + fusb0_int: fusb0-int {
> > > + rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> > > + };
> > > + };
> > > +
> > > + leds {
> > > + work_led_gpio: work_led-gpio {
> > > + rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> > > + };
> > > +
> > > + diy_led_gpio: diy_led-gpio {
> > > + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> > > + };
> > > + };
> > > +
> > > + pcie {
> > > + pcie_pwr_en: pcie-pwr-en {
> > > + rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
> > > + };
> > > + };
> > > +
> > > + pmic {
> > > + pmic_int_l: pmic-int-l {
> > > + rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
> > > + };
> > > +
> > > + vsel1_gpio: vsel1-gpio {
> > > + rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
> > > + };
> > > +
> > > + vsel2_gpio: vsel2-gpio {
> > > + rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> > > + };
> > > + };
> > > +
> > > + sdio-pwrseq {
> > > + wifi_enable_h: wifi-enable-h {
> > > + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> > > + };
> > > + };
> > > +
> > > + usb-typec {
> > > + vcc5v0_typec_en: vcc5v0_typec_en {
> > > + rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> > > + };
> > > + };
> > > +
> > > + usb2 {
> > > + vcc5v0_host_en: vcc5v0-host-en {
> > > + rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> > > + };
> > > + };
> > > +};
> > > +
> > > +&pwm0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&pwm2 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&saradc {
> > > + vref-supply = <&vcca1v8_s3>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&sdmmc {
> > > + bus-width = <4>;
> > > + cap-mmc-highspeed;
> > > + cap-sd-highspeed;
> > > + cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
> > > + disable-wp;
> > > + max-frequency = <150000000>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&sdhci {
> > > + bus-width = <8>;
> > > + mmc-hs400-1_8v;
> > > + mmc-hs400-enhanced-strobe;
> > > + non-removable;
> > > + status = "okay";
> > > +};
> > > +
> > > +&tcphy0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&tcphy1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&tsadc {
> > > + /* tshut mode 0:CRU 1:GPIO */
> > > + rockchip,hw-tshut-mode = <1>;
> > > + /* tshut polarity 0:LOW 1:HIGH */
> > > + rockchip,hw-tshut-polarity = <1>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&u2phy0 {
> > > + status = "okay";
> > > +
> > > + u2phy0_otg: otg-port {
> > > + status = "okay";
> > > + };
> > > +
> > > + u2phy0_host: host-port {
> > > + phy-supply = <&vcc5v0_host>;
> > > + status = "okay";
> > > + };
> > > +};
> > > +
> > > +&u2phy1 {
> > > + status = "okay";
> > > +
> > > + u2phy1_otg: otg-port {
> > > + status = "okay";
> > > + };
> > > +
> > > + u2phy1_host: host-port {
> > > + phy-supply = <&vcc5v0_host>;
> > > + status = "okay";
> > > + };
> > > +};
> > > +
> > > +&uart0 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&uart0_xfer &uart0_cts>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart2 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_host0_ehci {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_host0_ohci {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_host1_ehci {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_host1_ohci {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbdrd3_0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbdrd_dwc3_0 {
> > > + status = "okay";
> > > + dr_mode = "otg";
> > > +};
> > > +
> > > +&usbdrd3_1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbdrd_dwc3_1 {
> > > + status = "okay";
> > > + dr_mode = "host";
> > > +};
> > > +
> > > +&vopb {
> > > + status = "okay";
> > > +};
> > > +
> > > +&vopb_mmu {
> > > + status = "okay";
> > > +};
> > > +
> > > +&vopl {
> > > + status = "okay";
> > > +};
> > > +
> > > +&vopl_mmu {
> > > + status = "okay";
> > > +};
> > > diff --git a/board/rockchip/evb_rk3399/MAINTAINERS b/board/rockchip/evb_rk3399/MAINTAINERS
> > > index 1f51f65160..295730c91b 100644
> > > --- a/board/rockchip/evb_rk3399/MAINTAINERS
> > > +++ b/board/rockchip/evb_rk3399/MAINTAINERS
> > > @@ -30,3 +30,10 @@ S: Maintained
> > > F: configs/orangepi-rk3399_defconfig
> > > F: arch/arm/dts/rk3399-u-boot.dtsi
> > > F: arch/arm/dts/rk3399-orangepi-u-boot.dtsi
> > > +
> > > +ROCKPRO64
> > > +M: Akash Gajjar <akash at openedev.com>
> > > +M: Jagan Teki <jagan at amarulasolutions.com>
> > > +S: Maintained
> > > +F: configs/rockpro64-rk3399_defconfig
> > > +F: arch/arm/dts/rk3399-rockpro64-u-boot.dtsi
> > > diff --git a/configs/rockpro64-rk3399_defconfig b/configs/rockpro64-rk3399_defconfig
> > > new file mode 100644
> > > index 0000000000..90bcaedbd2
> > > --- /dev/null
> > > +++ b/configs/rockpro64-rk3399_defconfig
> > > @@ -0,0 +1,60 @@
> > > +CONFIG_ARM=y
> > > +CONFIG_ARCH_ROCKCHIP=y
> > > +CONFIG_SYS_TEXT_BASE=0x00200000
> > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > > +CONFIG_SYS_MALLOC_F_LEN=0x4000
> > > +CONFIG_ROCKCHIP_RK3399=y
> > > +CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
> > > +CONFIG_DEBUG_UART_BASE=0xFF1A0000
> > > +CONFIG_DEBUG_UART_CLOCK=24000000
> > > +CONFIG_SPL_STACK_R_ADDR=0x80000
> > > +CONFIG_DEBUG_UART=y
> > > +CONFIG_NR_DRAM_BANKS=1
> > > +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rockpro64.dtb"
> > > +# CONFIG_DISPLAY_CPUINFO is not set
> > > +CONFIG_DISPLAY_BOARDINFO_LATE=y
> > > +CONFIG_SPL_STACK_R=y
> > > +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> > > +CONFIG_CMD_BOOTZ=y
> > > +CONFIG_CMD_GPT=y
> > > +CONFIG_CMD_MMC=y
> > > +CONFIG_CMD_SF=y
> > > +CONFIG_CMD_USB=y
> > > +# CONFIG_CMD_SETEXPR is not set
> > > +CONFIG_CMD_TIME=y
> > > +CONFIG_SPL_OF_CONTROL=y
> > > +CONFIG_DEFAULT_DEVICE_TREE="rk3399-rockpro64"
> > > +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> > > +CONFIG_TPL=y
> > > +CONFIG_ENV_IS_IN_MMC=y
> > > +CONFIG_ROCKCHIP_GPIO=y
> > > +CONFIG_SYS_I2C_ROCKCHIP=y
> > > +CONFIG_MMC_DW=y
> > > +CONFIG_MMC_DW_ROCKCHIP=y
> > > +CONFIG_MMC_SDHCI=y
> > > +CONFIG_MMC_SDHCI_ROCKCHIP=y
> > > +CONFIG_DM_ETH=y
> > > +CONFIG_ETH_DESIGNWARE=y
> > > +CONFIG_GMAC_ROCKCHIP=y
> > > +CONFIG_PMIC_RK8XX=y
> > > +CONFIG_REGULATOR_PWM=y
> > > +CONFIG_REGULATOR_RK8XX=y
> > > +CONFIG_PWM_ROCKCHIP=y
> > > +CONFIG_BAUDRATE=1500000
> > > +CONFIG_DEBUG_UART_SHIFT=2
> > > +CONFIG_SYSRESET=y
> > > +CONFIG_USB=y
> > > +CONFIG_USB_XHCI_HCD=y
> > > +CONFIG_USB_XHCI_DWC3=y
> > > +CONFIG_USB_EHCI_HCD=y
> > > +CONFIG_USB_EHCI_GENERIC=y
> > > +CONFIG_USB_HOST_ETHER=y
> > > +CONFIG_USB_ETHER_ASIX=y
> > > +CONFIG_USB_ETHER_ASIX88179=y
> > > +CONFIG_USB_ETHER_MCS7830=y
> > > +CONFIG_USB_ETHER_RTL8152=y
> > > +CONFIG_USB_ETHER_SMSC95XX=y
> > > +CONFIG_USE_TINY_PRINTF=y
> > > +CONFIG_SPL_TINY_MEMSET=y
> > > +CONFIG_ERRNO_STR=y
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > https://lists.denx.de/listinfo/u-boot
>
>
--
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
More information about the U-Boot
mailing list