[U-Boot] [EXT] Re: [PATCH v2 2/5] dm: spi: Convert Freescale ESPI driver to driver model
Chuanhua Han
chuanhua.han at nxp.com
Sun Jun 23 10:38:37 UTC 2019
Hi,
> -----Original Message-----
> From: Simon Glass <sjg at chromium.org>
> Sent: 2019年6月23日 3:10
> To: Chuanhua Han <chuanhua.han at nxp.com>
> Cc: Jagan Teki <jagan at openedev.com>; Wolfgang Denk <wd at denx.de>;
> Shengzhou Liu <shengzhou.liu at nxp.com>; Ruchika Gupta
> <ruchika.gupta at nxp.com>; U-Boot Mailing List <u-boot at lists.denx.de>;
> Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>; Jiafei Pan
> <jiafei.pan at nxp.com>; Yinbo Zhu <yinbo.zhu at nxp.com>; Bin Meng
> <bmeng.cn at gmail.com>; Jagdish Gediya <jagdish.gediya at nxp.com>
> Subject: [EXT] Re: [PATCH v2 2/5] dm: spi: Convert Freescale ESPI driver to
> driver model
>
> Caution: EXT Email
>
> Hi,
>
> On Fri, 24 May 2019 at 05:39, Chuanhua Han <chuanhua.han at nxp.com>
> wrote:
> >
> > Modify the Freescale ESPI driver to support the driver model.
> > Also resolved the following problems:
> >
> > ===================== WARNING ====================== This board
> does
> > not use CONFIG_DM_SPI. Please update the board before v2019.04 for no
> > dm conversion and v2019.07 for partially dm converted drivers.
> > Failure to update can lead to driver/board removal See
> > doc/driver-model/MIGRATION.txt for more info.
> > ====================================================
> > ===================== WARNING ====================== This board
> does
> > not use CONFIG_DM_SPI_FLASH. Please update the board to use
> > CONFIG_SPI_FLASH before the v2019.07 release.
> > Failure to update by the deadline may result in board removal.
> > See doc/driver-model/MIGRATION.txt for more info.
> > ====================================================
> >
> > Signed-off-by: Chuanhua Han <chuanhua.han at nxp.com>
> > ---
> > Changes in v2:
> > - The fsl_espi driver support both OF_CONTROL and PLATDATA
> >
> > drivers/spi/fsl_espi.c | 454
> > +++++++++++++++++++++++++++++------------
> > 1 file changed, 320 insertions(+), 134 deletions(-)
> >
> > diff --git a/drivers/spi/fsl_espi.c b/drivers/spi/fsl_espi.c index
> > 7444ae1a06..a2f4027fca 100644
> > --- a/drivers/spi/fsl_espi.c
> > +++ b/drivers/spi/fsl_espi.c
> > @@ -4,17 +4,27 @@
> > *
> > * Copyright 2010-2011 Freescale Semiconductor, Inc.
> > * Author: Mingkai Hu (Mingkai.hu at freescale.com)
> > + * Chuanhua Han (chuanhua.han at nxp.com)
> > */
> >
> > #include <common.h>
> > -
> > #include <malloc.h>
> > #include <spi.h>
> > #include <asm/immap_85xx.h>
>
> Please sort the includes - this one should go at the end
>
> > +#include <dm.h>
> > +#include <errno.h>
> > +#include <fdtdec.h>
> > +
> > +struct fsl_espi_platdata {
> > + uint flags;
> > + uint speed_hz;
> > + uint num_chipselect;
> > + fdt_addr_t regs_addr;
> > +};
> >
> > -struct fsl_spi_slave {
> > - struct spi_slave slave;
> > +struct fsl_espi_priv {
> > ccsr_espi_t *espi;
> > + u32 speed_hz;
> > unsigned int div16;
> > unsigned int pm;
> > int tx_timeout;
> > @@ -25,9 +35,18 @@ struct fsl_spi_slave {
> > unsigned int max_transfer_length;
> > };
> >
> > +struct fsl_spi_slave {
> > + struct spi_slave slave;
> > + struct fsl_espi_priv priv;
> > +};
> > +
> > #define to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave,
> > slave)
> > +#define to_fsl_spi_priv(p) container_of(p, struct fsl_spi_slave,
> > +priv)
>
> We shouldn't really need this. Can we just pass the containing stuct instead?
>
> > #define US_PER_SECOND 1000000UL
> >
> > +/* default SCK frequency, unit: HZ */
> > +#define FSL_ESPI_DEFAULT_SCK_FREQ 10000000
> > +
> > #define ESPI_MAX_CS_NUM 4
> > #define ESPI_FIFO_WIDTH_BIT 32
> >
> > @@ -62,121 +81,46 @@ struct fsl_spi_slave {
> >
> > #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
> >
> > -struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> > - unsigned int max_hz, unsigned int mode)
> > -{
> > - struct fsl_spi_slave *fsl;
> > - sys_info_t sysinfo;
> > - unsigned long spibrg = 0;
> > - unsigned long spi_freq = 0;
> > - unsigned char pm = 0;
> > -
> > - if (!spi_cs_is_valid(bus, cs))
> > - return NULL;
> > -
> > - fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
> > - if (!fsl)
> > - return NULL;
> > -
> > - fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
> > - fsl->mode = mode;
> > - fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
> > -
> > - /* Set eSPI BRG clock source */
> > - get_sys_info(&sysinfo);
> > - spibrg = sysinfo.freq_systembus / 2;
> > - fsl->div16 = 0;
> > - if ((spibrg / max_hz) > 32) {
> > - fsl->div16 = ESPI_CSMODE_DIV16;
> > - pm = spibrg / (max_hz * 16 * 2);
> > - if (pm > 16) {
> > - pm = 16;
> > - debug("Requested speed is too low: %d Hz, %ld
> Hz "
> > - "is used.\n", max_hz, spibrg / (32 * 16));
> > - }
> > - } else
> > - pm = spibrg / (max_hz * 2);
> > - if (pm)
> > - pm--;
> > - fsl->pm = pm;
> > -
> > - if (fsl->div16)
> > - spi_freq = spibrg / ((pm + 1) * 2 * 16);
> > - else
> > - spi_freq = spibrg / ((pm + 1) * 2);
> > -
> > - /* set tx_timeout to 10 times of one espi FIFO entry go out */
> > - fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND *
> ESPI_FIFO_WIDTH_BIT
> > - * 10), spi_freq);
> > -
> > - return &fsl->slave;
> > -}
> > -
> > -void spi_free_slave(struct spi_slave *slave)
> > +#ifndef CONFIG_DM_SPI
>
> It is more common to put #idef CONFIG_DM_SPI first with the old code last.
>
> > +void spi_cs_activate(struct spi_slave *slave)
> > {
> > struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > - free(fsl);
> > -}
> > + ccsr_espi_t *espi = fsl->priv.espi;
> > + unsigned int com = 0;
> > + size_t data_len = fsl->priv.data_len;
> >
> > -int spi_claim_bus(struct spi_slave *slave)
> > + com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
> > + com |= ESPI_COM_CS(slave->cs);
> > + com |= ESPI_COM_TRANLEN(data_len - 1);
> > + out_be32(&espi->com, com);
> > +}
> > +#else
> > +void fsl_spi_cs_activate(struct fsl_espi_priv *priv, uint cs)
> > {
> > - struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > - ccsr_espi_t *espi = fsl->espi;
> > - unsigned char pm = fsl->pm;
> > - unsigned int cs = slave->cs;
> > - unsigned int mode = fsl->mode;
> > - unsigned int div16 = fsl->div16;
> > - int i;
> > -
> > - debug("%s: bus:%i cs:%i\n", __func__, slave->bus, cs);
> > -
> > - /* Enable eSPI interface */
> > - out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
> > - | ESPI_MODE_TXTHR(4) | ESPI_MODE_EN);
> > -
> > - out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
> > - out_be32(&espi->mask, 0x00000000); /* Mask all eSPI interrupts
> */
> > -
> > - /* Init CS mode interface */
> > - for (i = 0; i < ESPI_MAX_CS_NUM; i++)
> > - out_be32(&espi->csmode[i], ESPI_CSMODE_INIT_VAL);
> > -
> > - out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
> > - ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
> > - | ESPI_CSMODE_CI_INACTIVEHIGH |
> ESPI_CSMODE_CP_BEGIN_EDGCLK
> > - | ESPI_CSMODE_REV_MSB_FIRST |
> ESPI_CSMODE_LEN(0xF)));
> > -
> > - /* Set eSPI BRG clock source */
> > - out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > - | ESPI_CSMODE_PM(pm) | div16);
> > -
> > - /* Set eSPI mode */
> > - if (mode & SPI_CPHA)
> > - out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > - | ESPI_CSMODE_CP_BEGIN_EDGCLK);
> > - if (mode & SPI_CPOL)
> > - out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > - | ESPI_CSMODE_CI_INACTIVEHIGH);
> > -
> > - /* Character bit order: msb first */
> > - out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > - | ESPI_CSMODE_REV_MSB_FIRST);
> > -
> > - /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */
> > - out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > - | ESPI_CSMODE_LEN(7));
> > + ccsr_espi_t *espi = priv->espi;
> > + unsigned int com = 0;
> > + size_t data_len = priv->data_len;
> >
> > - return 0;
> > + com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
> > + com |= ESPI_COM_CS(cs);
> > + com |= ESPI_COM_TRANLEN(data_len - 1);
> > + out_be32(&espi->com, com);
> > }
> > +#endif
> >
> > -void spi_release_bus(struct spi_slave *slave)
> > +void spi_cs_deactivate(struct spi_slave *slave)
>
> Should this be static?
>
I have sent the fourth edition you see the new patchwork:
https://patchwork.ozlabs.org/project/uboot/list/?series=115242
> Regards,
> Simon
More information about the U-Boot
mailing list