[U-Boot] [PATCH v2 29/41] board: ge: mx53ppd: enable DM_VIDEO
Robert Beckett
bob.beckett at collabora.com
Wed Oct 23 18:21:50 UTC 2019
From: Ian Ray <ian.ray at ge.com>
Enable DM_VIDEO for mx53ppd. This also requires DM_REGULATOR_FIXED and
DM_PWM for the backlight, and `failbootcmd' is changed to use lcdputs.
Remove unused MX53PPD_LCD_POWER.
Signed-off-by: Ian Ray <ian.ray at ge.com>
Signed-off-by: Robert Beckett <bob.beckett at collabora.com>
---
arch/arm/dts/imx53-ppd.dts | 70 +++++++++++++++++++++++
board/ge/mx53ppd/Makefile | 2 +-
board/ge/mx53ppd/mx53ppd.c | 2 -
board/ge/mx53ppd/mx53ppd_video.c | 96 ++++++++++++++++++--------------
board/ge/mx53ppd/ppd_gpio.h | 2 -
configs/mx53ppd_defconfig | 5 +-
include/configs/mx53ppd.h | 11 ++--
7 files changed, 133 insertions(+), 55 deletions(-)
diff --git a/arch/arm/dts/imx53-ppd.dts b/arch/arm/dts/imx53-ppd.dts
index 3a3192d5e8..947d75b05d 100644
--- a/arch/arm/dts/imx53-ppd.dts
+++ b/arch/arm/dts/imx53-ppd.dts
@@ -7,6 +7,7 @@
/dts-v1/;
#include "imx53.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "General Electric CS ONE";
@@ -21,6 +22,69 @@
compatible = "u-boot,bootcount-i2c-eeprom";
i2c-eeprom = <&bootcount_eeprom>;
};
+
+ reg_3v3: regulator-3v3 {
+ /* TPS54320 */
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_3v3_lcd: regulator-3v3-lcd {
+ /* MIC2009 */
+ compatible = "regulator-fixed";
+ regulator-name = "LCD_3V3";
+ vin-supply = <®_3v3>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ pwm_bl: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 50000>;
+ brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35
+ 38 40 43 45 48 51 53 56 58 61 63 66 68 71
+ 73 76 79 81 84 86 89 91 94 96 99 102 104
+ 107 109 112 114 117 119 122 124 127 130
+ 132 135 137 140 142 145 147 150 153 155
+ 158 160 163 165 168 170 173 175 178 181
+ 183 186 188 191 193 196 198 201 204 206
+ 209 211 214 216 219 221 224 226 229 232
+ 234 237 239 242 244 247 249 252 255>;
+ default-brightness-level = <0>;
+ enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_3v3_lcd>;
+ };
+
+ panel-lvds0 {
+ compatible = "simple-panel";
+ backlight = <&pwm_bl>;
+ power-supply = <®_3v3_lcd>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ status = "okay";
+
+ port at 2 {
+ reg = <2>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
};
&iomuxc {
@@ -41,6 +105,12 @@
>;
};
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT9__PWM2_PWMO 0x5
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX53_PAD_EIM_D21__I2C1_SCL 0x400001e4
diff --git a/board/ge/mx53ppd/Makefile b/board/ge/mx53ppd/Makefile
index 9fae414399..f423e80cae 100644
--- a/board/ge/mx53ppd/Makefile
+++ b/board/ge/mx53ppd/Makefile
@@ -7,4 +7,4 @@
# Jason Liu <r64343 at freescale.com>
obj-y += mx53ppd.o
-obj-$(CONFIG_VIDEO) += mx53ppd_video.o
+obj-$(CONFIG_DM_VIDEO) += mx53ppd_video.o
diff --git a/board/ge/mx53ppd/mx53ppd.c b/board/ge/mx53ppd/mx53ppd.c
index 2586daddf3..17ba3a87dd 100644
--- a/board/ge/mx53ppd/mx53ppd.c
+++ b/board/ge/mx53ppd/mx53ppd.c
@@ -38,8 +38,6 @@
#include "../../ge/common/ge_common.h"
#include "../../ge/common/vpd_reader.h"
-#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
-
DECLARE_GLOBAL_DATA_PTR;
static u32 mx53_dram_size[2];
diff --git a/board/ge/mx53ppd/mx53ppd_video.c b/board/ge/mx53ppd/mx53ppd_video.c
index 9dd9f0c98d..c386dc29de 100644
--- a/board/ge/mx53ppd/mx53ppd_video.c
+++ b/board/ge/mx53ppd/mx53ppd_video.c
@@ -9,35 +9,49 @@
*/
#include <common.h>
+#include <dm.h>
#include <linux/list.h>
-#include <asm/gpio.h>
#include <asm/arch/iomux-mx53.h>
+#include <asm/mach-imx/video.h>
#include <linux/fb.h>
#include <ipu_pixfmt.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
#include <asm/io.h>
-#include <pwm.h>
-#include "ppd_gpio.h"
-
-#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
-
-static struct fb_videomode const nv_spwg = {
- .name = "NV-SPWGRGB888",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 15384,
- .left_margin = 16,
- .right_margin = 210,
- .upper_margin = 10,
- .lower_margin = 22,
- .hsync_len = 30,
- .vsync_len = 13,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
+#include <panel.h>
+
+static int detect_lcd(struct display_info_t const *dev)
+{
+ return 1;
+}
+
+struct display_info_t const displays[] = {
+ {
+ .bus = -1,
+ .addr = -1,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = detect_lcd,
+ .enable = NULL,
+ .mode = {
+ .name = "NV-SPWGRGB888",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 15384,
+ .left_margin = 16,
+ .right_margin = 210,
+ .upper_margin = 10,
+ .lower_margin = 22,
+ .hsync_len = 30,
+ .vsync_len = 13,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+ }
+ }
};
+size_t display_count = ARRAY_SIZE(displays);
+
void setup_iomux_lcd(void)
{
static const iomux_v3_cfg_t lcd_pads[] = {
@@ -96,24 +110,31 @@ static void lcd_enable(void)
IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
&iomux->gpr[2]);
-
- /* Enable backlights */
- pwm_init(1, 0, 0);
-
- /* duty cycle 5000000ns, period: 5000000ns */
- pwm_config(1, 5000000, 5000000);
-
- /* Backlight Power */
- gpio_request(BACKLIGHT_ENABLE, "BACKLIGHT_ENABLE");
- gpio_direction_output(BACKLIGHT_ENABLE, 1);
-
- pwm_enable(1);
}
static int do_lcd_enable(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
lcd_enable();
+
+ int ret;
+ struct udevice *panel;
+ struct udevice *dev;
+
+ ret = uclass_get_device(UCLASS_PANEL, 0, &panel);
+ if (ret)
+ return ret;
+
+ panel_set_backlight(panel, 100);
+ panel_enable_backlight(panel);
+
+ /* Probe, to find a video device to be used to show a message on
+ * the vidconsole.
+ */
+ ret = uclass_get_device(UCLASS_VIDEO, 0, &dev);
+ if (ret)
+ return ret;
+
return 0;
}
@@ -122,14 +143,3 @@ U_BOOT_CMD(
"enable PPD LCD",
"no parameters"
);
-
-int board_video_skip(void)
-{
- int ret;
-
- ret = ipuv3_fb_init(&nv_spwg, 0, IPU_PIX_FMT_RGB24);
- if (ret)
- printf("Display cannot be configured: %d\n", ret);
-
- return ret;
-}
diff --git a/board/ge/mx53ppd/ppd_gpio.h b/board/ge/mx53ppd/ppd_gpio.h
index 12bb389629..98c41d4d67 100644
--- a/board/ge/mx53ppd/ppd_gpio.h
+++ b/board/ge/mx53ppd/ppd_gpio.h
@@ -51,7 +51,6 @@ struct gpio_cfg {
#define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22)
#define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27)
#define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17)
-#define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29)
#define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18)
#define ECSPI1_CS0 IMX_GPIO_NR(5, 17)
#define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
@@ -81,7 +80,6 @@ static const struct gpio_cfg ppd_gpios[] = {
{ POWER_DOWN_LVDS0_DESERIALIZER_N, 1 },
{ POWER_DOWN_LVDS1_DESERIALIZER_N, 1 },
{ ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 },
- { BACKLIGHT_ENABLE, 0 },
{ RESET_I2C1_BUS_SEGMENT_MUX_N, 1 },
{ ECSPI1_CS0, 1 },
{ ECSPI1_CS1, 1 },
diff --git a/configs/mx53ppd_defconfig b/configs/mx53ppd_defconfig
index 51d79f602a..4d4f93614f 100644
--- a/configs/mx53ppd_defconfig
+++ b/configs/mx53ppd_defconfig
@@ -53,7 +53,6 @@ CONFIG_RTC_S35392A=y
CONFIG_USB=y
CONFIG_USB_EHCI_MX5=y
CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
# CONFIG_VIDEO_SW_CURSOR is not set
CONFIG_WATCHDOG_TIMEOUT_MSECS=8000
CONFIG_IMX_WATCHDOG=y
@@ -61,5 +60,9 @@ CONFIG_WDT=y
CONFIG_SYSRESET=y
CONFIG_SYSRESET_WATCHDOG=y
CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_USB=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_DM_PWM=y
diff --git a/include/configs/mx53ppd.h b/include/configs/mx53ppd.h
index 941b8c00cc..c7414213a7 100644
--- a/include/configs/mx53ppd.h
+++ b/include/configs/mx53ppd.h
@@ -92,12 +92,9 @@
"swappartitions=setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
"ppd_lcd_enable; " \
- "msg=\"Monitor failed to start. " \
- "Try again, or contact GE Service for support.\"; " \
- "echo $msg; " \
- "setenv stdout vga; " \
- "echo \"\n\n\n\n \" $msg; " \
- "setenv stdout serial; " \
+ "setcurs 5 4; " \
+ "lcdputs \"Monitor failed to start. " \
+ "Try again, or contact GE Service for support.\"; " \
"bootcount reset; \0" \
"altbootcmd=" \
"run doquiet; " \
@@ -174,4 +171,6 @@
/* Backlight Control */
#define CONFIG_IMX6_PWM_PER_CLK 66666000
+#define CONFIG_IMX_VIDEO_SKIP
+
#endif /* __CONFIG_H */
--
2.20.1
More information about the U-Boot
mailing list