[U-Boot] [PATCH] arm: imx6: cm_fx6: Enable DM SPI and SPI_FLASH, fix SPL build errors

sunil.m at techveda.org sunil.m at techveda.org
Mon Sep 2 13:43:45 UTC 2019


From: Suniel Mahesh <sunil.m at techveda.org>

Enable driver model for SPI and SPI_FLASH to remove the following
compile warning on CM-FX6 SOM:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================

This change introduced SPL build error as shown:

In file included from include/common.h:47:0,
                 from drivers/mtd/spi/sf_probe.c:10:
drivers/mtd/spi/sf_probe.c: In function 'spi_flash_std_probe':
drivers/mtd/spi/sf_probe.c:149:54: error: dereferencing pointer to incomplete type 'struct dm_spi_slave_platdata'
scripts/Makefile.build:278: recipe for target 'spl/drivers/mtd/spi/sf_probe.o' failed
make[3]: *** [spl/drivers/mtd/spi/sf_probe.o] Error 1
scripts/Makefile.build:432: recipe for target 'spl/drivers/mtd/spi' failed
make[2]: *** [spl/drivers/mtd/spi] Error 2

Disabling DM for SPI support(SPI and SF) in SPL resolves the issue.
Target was compile tested, build was clean.

Signed-off-by: Suniel Mahesh <sunil.m at techveda.org>
---
 configs/cm_fx6_defconfig | 2 ++
 include/configs/cm_fx6.h | 7 +++++++
 2 files changed, 9 insertions(+)

diff --git a/configs/cm_fx6_defconfig b/configs/cm_fx6_defconfig
index fd0db4d..d236875 100644
--- a/configs/cm_fx6_defconfig
+++ b/configs/cm_fx6_defconfig
@@ -62,6 +62,7 @@ CONFIG_FSL_USDHC=y
 CONFIG_NAND=y
 CONFIG_NAND_MXS=y
 CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=25000000
 CONFIG_SPI_FLASH_ATMEL=y
@@ -77,6 +78,7 @@ CONFIG_MII=y
 CONFIG_DM_PMIC=y
 CONFIG_DM_REGULATOR=y
 CONFIG_SPI=y
+CONFIG_DM_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h
index b957e9c..4dd2b40 100644
--- a/include/configs/cm_fx6.h
+++ b/include/configs/cm_fx6.h
@@ -163,6 +163,13 @@
 /* APBH DMA is required for NAND support */
 #endif
 
+/* SPI Flash Configs */
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
+#undef CONFIG_SPI_FLASH_MTD
+#endif
+
 /* Ethernet */
 #define CONFIG_FEC_MXC
 #define CONFIG_FEC_MXC_PHYADDR		0
-- 
2.7.4



More information about the U-Boot mailing list