[U-Boot] [PATCH v2 11/14] ARM: Update display5_factory_defconfig after switch to DM/DTS and uuu utility

[Lukasz Majewski]

This commit updates the display5_factory_defconfig file after the switch
to DM/DTS for this board.

Moreover, the VID and PID for SPL running SDP gadget have been updated to
allow seamless work with 'uuu' utility from NXP (the imx_usb doesn't work
properly after embedding the u-boot proper into fitImage - problem with IVT
embedding in FIT).

Example to use 'uuu' session:

cat << EOF > display5_recovery.lst
uuu_version 1.2.135
SDP: boot -f /srv/tftp/SPL
SDPU: write -f /srv/tftp/u-boot-dtb.img -addr 0x10000000
SDPU: jump -addr 0x10000000
SDPU: done
EOF

sudo ./uuu/uuu display5_recovery.lst

Signed-off-by: Lukasz Majewski <lukma at denx.de>
---

Changes in v2: None

 configs/display5_factory_defconfig | 41 ++++++++++++++++++++++++++++++++++----
 1 file changed, 37 insertions(+), 4 deletions(-)

diff --git a/configs/display5_factory_defconfig b/configs/display5_factory_defconfig
index c467e8c92890..b4b030a32b76 100644
--- a/configs/display5_factory_defconfig
+++ b/configs/display5_factory_defconfig
@@ -4,13 +4,19 @@ CONFIG_SYS_TEXT_BASE=0x17800000
 CONFIG_SPL_GPIO_SUPPORT=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x1000
+CONFIG_MX6_DDRCAL=y
 CONFIG_TARGET_DISPLAY5=y
+CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_SPL=y
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SPL_TEXT_BASE=0x00908000
 CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
 CONFIG_BOOTDELAY=3
@@ -19,8 +25,6 @@ CONFIG_BOOTCOMMAND="echo SDP Display5 recovery"
 CONFIG_SUPPORT_RAW_INITRD=y
 CONFIG_MISC_INIT_R=y
 CONFIG_BOUNCE_BUFFER=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
 # CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
 CONFIG_SPL_DMA_SUPPORT=y
 CONFIG_SPL_I2C_SUPPORT=y
@@ -47,11 +51,14 @@ CONFIG_CMD_PART=y
 CONFIG_CMD_SF=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_WDT=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_EXT4_WRITE=y
@@ -67,26 +74,52 @@ CONFIG_DEFAULT_DEVICE_TREE="imx6q-display5"
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_DFU_MMC=y
 CONFIG_DFU_SF=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_I2C_DEFAULT_BUS_NUMBER=0x2
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0x50
+CONFIG_SYS_I2C_EEPROM_BUS=2
+CONFIG_SYS_EEPROM_SIZE=32768
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
+CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD_DEVICE=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
 CONFIG_SF_DEFAULT_BUS=1
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=50000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
 CONFIG_SPI_FLASH_SPANSION=y
 CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
 CONFIG_PHYLIB=y
+CONFIG_PHY_MARVELL=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
 CONFIG_MXC_UART=y
 CONFIG_SPI=y
 CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_USB=y
+CONFIG_DM_USB=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="Liebherr"
-CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
-CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
 CONFIG_CI_UDC=y
 CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_I2C_EDID=y
 CONFIG_IMX_WATCHDOG=y
+CONFIG_PANIC_HANG=y
-- 
2.11.0