[U-Boot] [PATCH v5 02/19] env: define env context for U-Boot environment
AKASHI Takahiro
takahiro.akashi at linaro.org
Thu Sep 5 08:21:16 UTC 2019
In this patch, env context fo U-Boot environment is defined to utilize
new env interfaces, maintaining the compatibility with the existing
semantics and Kconfig configuration.
In this commit, FAT file system and flash device are only supported
devices for backing storages, but extending to other devices will be
quite straightforward.
Signed-off-by: AKASHI Takahiro <takahiro.akashi at linaro.org>
---
env/Kconfig.uboot | 671 ++++++++++++++++++++++++++++++++++++++++++++
env/Makefile | 2 +-
env/env_ctx_uboot.c | 292 +++++++++++++++++++
include/env.h | 3 +
4 files changed, 967 insertions(+), 1 deletion(-)
create mode 100644 env/Kconfig.uboot
create mode 100644 env/env_ctx_uboot.c
diff --git a/env/Kconfig.uboot b/env/Kconfig.uboot
new file mode 100644
index 000000000000..e4334f7f2878
--- /dev/null
+++ b/env/Kconfig.uboot
@@ -0,0 +1,671 @@
+config ENV_IS_NOWHERE
+ bool "U-Boot Environment is not stored"
+ default y if !ENV_IS_IN_EEPROM && !ENV_IS_IN_EXT4 && \
+ !ENV_IS_IN_FAT && !ENV_IS_IN_FLASH && \
+ !ENV_IS_IN_MMC && !ENV_IS_IN_NAND && \
+ !ENV_IS_IN_NVRAM && !ENV_IS_IN_ONENAND && \
+ !ENV_IS_IN_REMOTE && !ENV_IS_IN_SPI_FLASH && \
+ !ENV_IS_IN_UBI
+ help
+ Define this if you don't want to or can't have an environment stored
+ on a storage medium. In this case the environment will still exist
+ while U-Boot is running, but once U-Boot exits it will not be
+ stored. U-Boot will therefore always start up with a default
+ environment.
+
+config ENV_IS_IN_EEPROM
+ bool "Environment in EEPROM"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_EEPROM
+ help
+ Use this if you have an EEPROM or similar serial access
+ device and a driver for it.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the total memory of your EEPROM.
+
+ Note that we consider the length of the address field to
+ still be one byte because the extra address bits are hidden
+ in the chip address.
+
+ - CONFIG_ENV_EEPROM_IS_ON_I2C
+ define this, if you have I2C and SPI activated, and your
+ EEPROM, which holds the environment, is on the I2C bus.
+
+ - CONFIG_I2C_ENV_EEPROM_BUS
+ if you have an Environment on an EEPROM reached over
+ I2C muxes, you can define here, how to reach this
+ EEPROM. For example:
+
+ #define CONFIG_I2C_ENV_EEPROM_BUS 1
+
+ EEPROM which holds the environment, is reached over
+ a pca9547 i2c mux with address 0x70, channel 3.
+
+config ENV_IS_IN_FAT
+ bool "Environment is in a FAT filesystem"
+ depends on !CHAIN_OF_TRUST
+ default y if ARCH_BCM283X
+ default y if ARCH_SUNXI && MMC
+ default y if MMC_OMAP_HS && TI_COMMON_CMD_OPTIONS
+ select ENV_DRV_FAT
+ help
+ Define this if you want to use the FAT file system for the environment.
+
+config ENV_IS_IN_EXT4
+ bool "Environment is in a EXT4 filesystem"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_EXT4
+ help
+ Define this if you want to use the EXT4 file system for the environment.
+
+config ENV_IS_IN_FLASH
+ bool "Environment in flash memory"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_FLASH
+ default y if ARCH_CINTEGRATOR
+ default y if ARCH_INTEGRATOR_CP
+ default y if M548x || M547x || M5282 || MCF547x_8x
+ default y if MCF532x || MCF52x2
+ default y if MPC86xx || MPC83xx
+ default y if ARCH_MPC8572 || ARCH_MPC8548 || ARCH_MPC8641
+ default y if SH && !CPU_SH4
+ help
+ Define this if you have a flash device which you want to use for the
+ environment.
+
+ a) The environment occupies one whole flash sector, which is
+ "embedded" in the text segment with the U-Boot code. This
+ happens usually with "bottom boot sector" or "top boot
+ sector" type flash chips, which have several smaller
+ sectors at the start or the end. For instance, such a
+ layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
+ such a case you would place the environment in one of the
+ 4 kB sectors - with U-Boot code before and after it. With
+ "top boot sector" type flash chips, you would put the
+ environment in one of the last sectors, leaving a gap
+ between U-Boot and the environment.
+
+ CONFIG_ENV_OFFSET:
+
+ Offset of environment data (variable area) to the
+ beginning of flash memory; for instance, with bottom boot
+ type flash chips the second sector can be used: the offset
+ for this sector is given here.
+
+ CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
+
+ CONFIG_ENV_ADDR:
+
+ This is just another way to specify the start address of
+ the flash sector containing the environment (instead of
+ CONFIG_ENV_OFFSET).
+
+ CONFIG_ENV_SECT_SIZE:
+
+ Size of the sector containing the environment.
+
+
+ b) Sometimes flash chips have few, equal sized, BIG sectors.
+ In such a case you don't want to spend a whole sector for
+ the environment.
+
+ CONFIG_ENV_SIZE:
+
+ If you use this in combination with CONFIG_ENV_IS_IN_FLASH
+ and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
+ of this flash sector for the environment. This saves
+ memory for the RAM copy of the environment.
+
+ It may also save flash memory if you decide to use this
+ when your environment is "embedded" within U-Boot code,
+ since then the remainder of the flash sector could be used
+ for U-Boot code. It should be pointed out that this is
+ STRONGLY DISCOURAGED from a robustness point of view:
+ updating the environment in flash makes it always
+ necessary to erase the WHOLE sector. If something goes
+ wrong before the contents has been restored from a copy in
+ RAM, your target system will be dead.
+
+ CONFIG_ENV_ADDR_REDUND
+ CONFIG_ENV_SIZE_REDUND
+
+ These settings describe a second storage area used to hold
+ a redundant copy of the environment data, so that there is
+ a valid backup copy in case there is a power failure during
+ a "saveenv" operation.
+
+ BE CAREFUL! Any changes to the flash layout, and some changes to the
+ source code will make it necessary to adapt <board>/u-boot.lds*
+ accordingly!
+
+config ENV_IS_IN_MMC
+ bool "Environment in an MMC device"
+ depends on !CHAIN_OF_TRUST
+ depends on MMC
+ select ENV_DRV_MMC
+ default y if ARCH_EXYNOS4
+ default y if MX6SX || MX7D
+ default y if TEGRA30 || TEGRA124
+ default y if TEGRA_ARMV8_COMMON
+ help
+ Define this if you have an MMC device which you want to use for the
+ environment.
+
+ CONFIG_SYS_MMC_ENV_DEV:
+
+ Specifies which MMC device the environment is stored in.
+
+ CONFIG_SYS_MMC_ENV_PART (optional):
+
+ Specifies which MMC partition the environment is stored in. If not
+ set, defaults to partition 0, the user area. Common values might be
+ 1 (first MMC boot partition), 2 (second MMC boot partition).
+
+ CONFIG_ENV_OFFSET:
+ CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the environment
+ area within the specified MMC device.
+
+ If offset is positive (the usual case), it is treated as relative to
+ the start of the MMC partition. If offset is negative, it is treated
+ as relative to the end of the MMC partition. This can be useful if
+ your board may be fitted with different MMC devices, which have
+ different sizes for the MMC partitions, and you always want the
+ environment placed at the very end of the partition, to leave the
+ maximum possible space before it, to store other data.
+
+ These two values are in units of bytes, but must be aligned to an
+ MMC sector boundary.
+
+ CONFIG_ENV_OFFSET_REDUND (optional):
+
+ Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
+ hold a redundant copy of the environment data. This provides a
+ valid backup copy in case the other copy is corrupted, e.g. due
+ to a power failure during a "saveenv" operation.
+
+ This value may also be positive or negative; this is handled in the
+ same way as CONFIG_ENV_OFFSET.
+
+ This value is also in units of bytes, but must also be aligned to
+ an MMC sector boundary.
+
+ CONFIG_ENV_SIZE_REDUND (optional):
+
+ This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
+ set. If this value is set, it must be set to the same value as
+ CONFIG_ENV_SIZE.
+
+config ENV_IS_IN_NAND
+ bool "Environment in a NAND device"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_NAND
+ help
+ Define this if you have a NAND device which you want to use for the
+ environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the environment
+ area within the first NAND device. CONFIG_ENV_OFFSET must be
+ aligned to an erase block boundary.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ This setting describes a second storage area of CONFIG_ENV_SIZE
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
+ aligned to an erase block boundary.
+
+ - CONFIG_ENV_RANGE (optional):
+
+ Specifies the length of the region in which the environment
+ can be written. This should be a multiple of the NAND device's
+ block size. Specifying a range with more erase blocks than
+ are needed to hold CONFIG_ENV_SIZE allows bad blocks within
+ the range to be avoided.
+
+ - CONFIG_ENV_OFFSET_OOB (optional):
+
+ Enables support for dynamically retrieving the offset of the
+ environment from block zero's out-of-band data. The
+ "nand env.oob" command can be used to record this offset.
+ Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
+ using CONFIG_ENV_OFFSET_OOB.
+
+config ENV_IS_IN_NVRAM
+ bool "Environment in a non-volatile RAM"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_NVRAM
+ help
+ Define this if you have some non-volatile memory device
+ (NVRAM, battery buffered SRAM) which you want to use for the
+ environment.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines are used to determine the memory area you
+ want to use for environment. It is assumed that this memory
+ can just be read and written to, without any special
+ provision.
+
+config ENV_IS_IN_ONENAND
+ bool "Environment is in OneNAND"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_ONENAND
+ help
+ Define this if you want to put your local device's environment in
+ OneNAND.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines are used to determine the device range you
+ want to use for environment. It is assumed that this memory
+ can just be read and written to, without any special
+ provision.
+
+config ENV_IS_IN_REMOTE
+ bool "Environment is in remote memory space"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_REMOTE
+ help
+ Define this if you have a remote memory space which you
+ want to use for the local device's environment.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the address and size of the
+ environment area within the remote memory space. The
+ local device can get the environment from remote memory
+ space by SRIO or PCIE links.
+
+config ENV_IS_IN_SPI_FLASH
+ bool "Environment is in SPI flash"
+ depends on !CHAIN_OF_TRUST && SPI
+ select ENV_DRV_SPI_FLASH
+ default y if ARMADA_XP
+ default y if INTEL_BAYTRAIL
+ default y if INTEL_BRASWELL
+ default y if INTEL_BROADWELL
+ default y if NORTHBRIDGE_INTEL_IVYBRIDGE
+ default y if INTEL_QUARK
+ default y if INTEL_QUEENSBAY
+ help
+ Define this if you have a SPI Flash memory device which you
+ want to use for the environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SECT_SIZE:
+
+ Define the SPI flash's sector size.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ This setting describes a second storage area of CONFIG_ENV_SIZE
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
+ aligned to an erase sector boundary.
+
+config USE_ENV_SPI_BUS
+ bool "SPI flash bus for environment"
+ depends on ENV_IS_IN_SPI_FLASH
+ help
+ Force the SPI bus for environment.
+ If not defined, use CONFIG_SF_DEFAULT_BUS.
+
+config ENV_SPI_BUS
+ int "Value of SPI flash bus for environment"
+ depends on USE_ENV_SPI_BUS
+ help
+ Value the SPI bus and chip select for environment.
+
+config USE_ENV_SPI_CS
+ bool "SPI flash chip select for environment"
+ depends on ENV_IS_IN_SPI_FLASH
+ help
+ Force the SPI chip select for environment.
+ If not defined, use CONFIG_SF_DEFAULT_CS.
+
+config ENV_SPI_CS
+ int "Value of SPI flash chip select for environment"
+ depends on USE_ENV_SPI_CS
+ help
+ Value of the SPI chip select for environment.
+
+config USE_ENV_SPI_MAX_HZ
+ bool "SPI flash max frequency for environment"
+ depends on ENV_IS_IN_SPI_FLASH
+ help
+ Force the SPI max work clock for environment.
+ If not defined, use CONFIG_SF_DEFAULT_SPEED.
+
+config ENV_SPI_MAX_HZ
+ int "Value of SPI flash max frequency for environment"
+ depends on USE_ENV_SPI_MAX_HZ
+ help
+ Value of the SPI max work clock for environment.
+
+config USE_ENV_SPI_MODE
+ bool "SPI flash mode for environment"
+ depends on ENV_IS_IN_SPI_FLASH
+ help
+ Force the SPI work mode for environment.
+
+config ENV_SPI_MODE
+ hex "Value of SPI flash work mode for environment"
+ depends on USE_ENV_SPI_MODE
+ help
+ Value of the SPI work mode for environment.
+ See include/spi.h for value.
+
+config ENV_IS_IN_UBI
+ bool "Environment in a UBI volume"
+ depends on !CHAIN_OF_TRUST
+ select ENV_DRV_UBI
+ help
+ Define this if you have an UBI volume that you want to use for the
+ environment. This has the benefit of wear-leveling the environment
+ accesses, which is important on NAND.
+
+ - CONFIG_ENV_UBI_PART:
+
+ Define this to a string that is the mtd partition containing the UBI.
+
+ - CONFIG_ENV_UBI_VOLUME:
+
+ Define this to the name of the volume that you want to store the
+ environment in.
+
+ - CONFIG_ENV_UBI_VOLUME_REDUND:
+
+ Define this to the name of another volume to store a second copy of
+ the environment in. This will enable redundant environments in UBI.
+ It is assumed that both volumes are in the same MTD partition.
+
+config ENV_FAT_INTERFACE
+ string "Name of the block device for the environment"
+ depends on ENV_IS_IN_FAT
+ default "mmc" if ARCH_SUNXI
+ default "mmc" if TI_COMMON_CMD_OPTIONS || ARCH_ZYNQMP || ARCH_AT91
+ help
+ Define this to a string that is the name of the block device.
+
+config ENV_FAT_DEVICE_AND_PART
+ string "Device and partition for where to store the environment in FAT"
+ depends on ENV_IS_IN_FAT
+ default "0:1" if TI_COMMON_CMD_OPTIONS
+ default "0:auto" if ARCH_ZYNQMP
+ default "0:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA = -1
+ default "1:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA != -1
+ default "0" if ARCH_AT91
+ help
+ Define this to a string to specify the partition of the device. It can
+ be as following:
+
+ "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
+ - "D:P": device D partition P. Error occurs if device D has no
+ partition table.
+ - "D:0": device D.
+ - "D" or "D:": device D partition 1 if device D has partition
+ table, or the whole device D if has no partition
+ table.
+ - "D:auto": first partition in device D with bootable flag set.
+ If none, first valid partition in device D. If no
+ partition table then means device D.
+
+config ENV_FAT_FILE
+ string "Name of the FAT file to use for the environment"
+ depends on ENV_IS_IN_FAT
+ default "uboot.env"
+ help
+ It's a string of the FAT file name. This file use to store the
+ environment.
+
+config ENV_EXT4_INTERFACE
+ string "Name of the block device for the environment"
+ depends on ENV_IS_IN_EXT4
+ help
+ Define this to a string that is the name of the block device.
+
+config ENV_EXT4_DEVICE_AND_PART
+ string "Device and partition for where to store the environment in EXT4"
+ depends on ENV_IS_IN_EXT4
+ help
+ Define this to a string to specify the partition of the device. It can
+ be as following:
+
+ "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
+ - "D:P": device D partition P. Error occurs if device D has no
+ partition table.
+ - "D:0": device D.
+ - "D" or "D:": device D partition 1 if device D has partition
+ table, or the whole device D if has no partition
+ table.
+ - "D:auto": first partition in device D with bootable flag set.
+ If none, first valid partition in device D. If no
+ partition table then means device D.
+
+config ENV_EXT4_FILE
+ string "Name of the EXT4 file to use for the environment"
+ depends on ENV_IS_IN_EXT4
+ default "uboot.env"
+ help
+ It's a string of the EXT4 file name. This file use to store the
+ environment (explicit path to the file)
+
+if ARCH_ROCKCHIP || ARCH_SUNXI || ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL || ARC || ARCH_STM32MP || ARCH_OMAP2PLUS || ARCH_AT91
+
+config ENV_OFFSET
+ hex "Environment Offset"
+ depends on (!ENV_IS_IN_UBI && !ENV_IS_NOWHERE) || ARCH_STM32MP
+ default 0x3f8000 if ARCH_ROCKCHIP
+ default 0x88000 if ARCH_SUNXI
+ default 0xE0000 if ARCH_ZYNQ
+ default 0x1E00000 if ARCH_ZYNQMP
+ default 0 if ARC
+ default 0x140000 if ARCH_AT91
+ default 0x260000 if ARCH_OMAP2PLUS
+ help
+ Offset from the start of the device (or partition)
+
+config ENV_SIZE
+ hex "Environment Size"
+ default 0x40000 if ENV_IS_IN_SPI_FLASH && ARCH_ZYNQMP
+ default 0x20000 if ARCH_SUNXI || ARCH_ZYNQ || ARCH_OMAP2PLUS || ARCH_AT91
+ default 0x8000 if ARCH_ROCKCHIP || ARCH_ZYNQMP || ARCH_VERSAL
+ default 0x4000 if ARC
+ default 0x1f000
+ help
+ Size of the environment storage area
+
+config ENV_SECT_SIZE
+ hex "Environment Sector-Size"
+ depends on (!ENV_IS_NOWHERE && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_OMAP2PLUS || ARCH_AT91) )|| ARCH_STM32MP
+ default 0x40000 if ARCH_ZYNQMP
+ default 0x20000 if ARCH_ZYNQ || ARCH_OMAP2PLUS || ARCH_AT91
+ help
+ Size of the sector containing the environment.
+
+config ENV_UBI_PART
+ string "UBI partition name"
+ depends on ENV_IS_IN_UBI
+ help
+ MTD partition containing the UBI device
+
+config ENV_UBI_VOLUME
+ string "UBI volume name"
+ depends on ENV_IS_IN_UBI
+ help
+ Name of the volume that you want to store the environment in.
+
+config ENV_UBI_VOLUME_REDUND
+ string "UBI redundant volume name"
+ depends on ENV_IS_IN_UBI
+ help
+ Name of the redundant volume that you want to store the environment in.
+
+config ENV_UBI_VID_OFFSET
+ int "ubi environment VID offset"
+ depends on ENV_IS_IN_UBI
+ default 0
+ help
+ UBI VID offset for environment. If 0, no custom VID offset is used.
+
+endif
+
+config USE_DEFAULT_ENV_FILE
+ bool "Create default environment from file"
+ help
+ Normally, the default environment is automatically generated
+ based on the settings of various CONFIG_* options, as well
+ as the CONFIG_EXTRA_ENV_SETTINGS. By selecting this option,
+ you can instead define the entire default environment in an
+ external file.
+
+config DEFAULT_ENV_FILE
+ string "Path to default environment file"
+ depends on USE_DEFAULT_ENV_FILE
+ help
+ The path containing the default environment. The format is
+ the same as accepted by the mkenvimage tool: lines
+ containing key=value pairs, blank lines and lines beginning
+ with # are ignored.
+
+config ENV_VARS_UBOOT_RUNTIME_CONFIG
+ bool "Add run-time information to the environment"
+ help
+ Enable this in order to add variables describing certain
+ run-time determined information about the hardware to the
+ environment. These will be named board_name, board_rev.
+
+if SPL_ENV_SUPPORT
+config SPL_ENV_IS_NOWHERE
+ bool "SPL Environment is not stored"
+ default y if ENV_IS_NOWHERE
+ help
+ Similar to ENV_IS_NOWHERE, used for SPL environment.
+
+config SPL_ENV_IS_IN_MMC
+ bool "SPL Environment in an MMC device"
+ depends on !SPL_ENV_IS_NOWHERE
+ select ENV_DRV_MMC
+ default y
+ help
+ Similar to ENV_IS_IN_MMC, used for SPL environment.
+
+config SPL_ENV_IS_IN_FAT
+ bool "SPL Environment is in a FAT filesystem"
+ depends on !SPL_ENV_IS_NOWHERE
+ select ENV_DRV_FAT
+ default y
+ help
+ Similar to ENV_IS_IN_FAT, used for SPL environment.
+
+config SPL_ENV_IS_IN_EXT4
+ bool "SPL Environment is in a EXT4 filesystem"
+ depends on !SPL_ENV_IS_NOWHERE
+ select ENV_DRV_EXT4
+ default y
+ help
+ Similar to ENV_IS_IN_EXT4, used for SPL environment.
+
+config SPL_ENV_IS_IN_NAND
+ bool "SPL Environment in a NAND device"
+ depends on !SPL_ENV_IS_NOWHERE
+ select ENV_DRV_NAND
+ default y
+ help
+ Similar to ENV_IS_IN_NAND, used for SPL environment.
+
+config SPL_ENV_IS_IN_SPI_FLASH
+ bool "SPL Environment is in SPI flash"
+ depends on !SPL_ENV_IS_NOWHERE
+ select ENV_DRV_SPI_FLASH
+ default y
+ help
+ Similar to ENV_IS_IN_SPI_FLASH, used for SPL environment.
+
+config SPL_ENV_IS_IN_FLASH
+ bool "SPL Environment in flash memory"
+ depends on !SPL_ENV_IS_NOWHERE
+ select ENV_DRV_FLASH
+ default y
+ help
+ Similar to ENV_IS_IN_FLASH, used for SPL environment.
+
+endif
+
+if TPL_ENV_SUPPORT
+
+config TPL_ENV_IS_NOWHERE
+ bool "TPL Environment is not stored"
+ default y if ENV_IS_NOWHERE
+ help
+ Similar to ENV_IS_NOWHERE, used for TPL environment.
+
+config TPL_ENV_IS_IN_MMC
+ bool "TPL Environment in an MMC device"
+ depends on !TPL_ENV_IS_NOWHERE
+ select ENV_DRV_MMC
+ default y
+ help
+ Similar to ENV_IS_IN_MMC, used for TPL environment.
+
+config TPL_ENV_IS_IN_FAT
+ bool "TPL Environment is in a FAT filesystem"
+ depends on !TPL_ENV_IS_NOWHERE
+ select ENV_DRV_FAT
+ default y
+ help
+ Similar to ENV_IS_IN_FAT, used for TPL environment.
+
+config TPL_ENV_IS_IN_EXT4
+ bool "TPL Environment is in a EXT4 filesystem"
+ depends on !TPL_ENV_IS_NOWHERE
+ select ENV_DRV_EXT4
+ default y
+ help
+ Similar to ENV_IS_IN_EXT4, used for TPL environment.
+
+config TPL_ENV_IS_IN_NAND
+ bool "TPL Environment in a NAND device"
+ depends on !TPL_ENV_IS_NOWHERE
+ select ENV_DRV_NAND
+ default y
+ help
+ Similar to ENV_IS_IN_NAND, used for TPL environment.
+
+config TPL_ENV_IS_IN_SPI_FLASH
+ bool "TPL Environment is in SPI flash"
+ depends on !TPL_ENV_IS_NOWHERE
+ select ENV_DRV_SPI_FLASH
+ default y
+ help
+ Similar to ENV_IS_IN_SPI_FLASH, used for TPL environment.
+
+config TPL_ENV_IS_IN_FLASH
+ bool "TPL Environment in flash memory"
+ depends on !TPL_ENV_IS_NOWHERE
+ select ENV_DRV_FLASH
+ default y
+ help
+ Similar to ENV_IS_IN_FLASH, used for TPL environment.
+
+endif
diff --git a/env/Makefile b/env/Makefile
index ee37cc822024..0168eb47f00d 100644
--- a/env/Makefile
+++ b/env/Makefile
@@ -3,7 +3,7 @@
# (C) Copyright 2004-2006
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-obj-y += common.o env.o
+obj-y += common.o env.o env_ctx_uboot.o
ifndef CONFIG_SPL_BUILD
obj-y += attr.o
diff --git a/env/env_ctx_uboot.c b/env/env_ctx_uboot.c
new file mode 100644
index 000000000000..5ca645599347
--- /dev/null
+++ b/env/env_ctx_uboot.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Linaro Limited
+ * Author: AKASHI Takahiro
+ */
+
+#include <common.h>
+#include <env_default.h>
+#include <env_flags.h>
+#include <env_internal.h>
+#include <search.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if !defined(ENV_IS_IN_DEVICE) && !defined(CONFIG_ENV_IS_NOWHERE)
+# error Define one of CONFIG_ENV_IS_IN_{EEPROM|FLASH|MMC|FAT|EXT4|\
+NAND|NVRAM|ONENAND|SATA|SPI_FLASH|REMOTE|UBI} or CONFIG_ENV_IS_NOWHERE
+#endif
+
+struct hsearch_data env_htab = {
+#if CONFIG_IS_ENABLED(ENV_SUPPORT)
+ /* defined in flags.c, only compile with ENV_SUPPORT */
+ .change_ok = env_flags_validate,
+#endif
+};
+
+/*
+ * NOTE: extracted from env/env.c
+ */
+static bool env_has_inited_uboot(struct env_context *ctx,
+ enum env_location location)
+{
+ return gd->env_has_init & BIT(location);
+}
+
+static void env_set_inited_uboot(struct env_context *ctx,
+ enum env_location location)
+{
+ gd->env_has_init |= BIT(location);
+}
+
+static int env_get_load_prio_uboot(struct env_context *ctx)
+{
+ return gd->env_load_prio;
+}
+
+static enum env_location env_get_location_uboot(struct env_context *ctx,
+ enum env_operation op, int prio)
+{
+ gd->env_load_prio = prio;
+
+ return env_locations[prio];
+}
+
+int env_get_char_default_uboot(struct env_context *ctx, int index)
+{
+ return default_environment[index];
+}
+
+int env_get_char_spec_uboot(struct env_context *ctx, int index)
+{
+ return *(uchar *)(gd->env_addr + index);
+}
+
+static int env_init_uboot(struct env_context *ctx)
+{
+ struct env_driver *drv;
+ int ret = -ENOENT;
+ int prio;
+
+ for (prio = 0; (drv = env_driver_lookup(ctx, ENVOP_INIT, prio));
+ prio++) {
+ if (!drv->init || !(ret = drv->init(ctx)))
+ gd->env_has_init |= BIT(drv->location);
+
+ debug("%s: Environment %s init done (ret=%d)\n", __func__,
+ drv->name, ret);
+ }
+
+ if (!prio)
+ return -ENODEV;
+
+ if (ret == -ENOENT) {
+ gd->env_addr = (ulong)&default_environment[0];
+ gd->env_valid = ENV_VALID;
+
+ return 0;
+ }
+
+ return ret;
+}
+
+static int env_drv_init_uboot(struct env_context *ctx, enum env_location loc)
+{
+ __maybe_unused int ret;
+
+ switch (loc) {
+#ifdef CONFIG_ENV_IS_IN_FLASH
+ case ENVL_FLASH: {
+ env_hdr_t *env_ptr;
+ env_hdr_t *flash_addr;
+ ulong end_addr;
+ env_hdr_t *flash_addr_new;
+ ulong end_addr_new;
+
+#ifdef ENV_IS_EMBEDDED
+ env_ptr = &embedded_environment;
+#else /* ! ENV_IS_EMBEDDED */
+ env_ptr = (env_hdr_t *)CONFIG_ENV_ADDR;
+#endif /* ENV_IS_EMBEDDED */
+ flash_addr = (env_hdr_t *)CONFIG_ENV_ADDR;
+
+/* CONFIG_ENV_ADDR is supposed to be on sector boundary */
+ end_addr = CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1;
+
+#ifdef CONFIG_ENV_ADDR_REDUND
+ flash_addr_new = (env_hdr_t *)CONFIG_ENV_ADDR_REDUND;
+/* CONFIG_ENV_ADDR_REDUND is supposed to be on sector boundary */
+ end_addr_new = CONFIG_ENV_ADDR_REDUND
+ + CONFIG_ENV_SECT_SIZE - 1;
+#else
+ flash_addr_new = NULL;
+ end_addr_new = 0;
+#endif /* CONFIG_ENV_ADDR_REDUND */
+
+ ret = env_flash_init_params(ctx, env_ptr, flash_addr, end_addr,
+ flash_addr_new, end_addr_new,
+ (ulong)&default_environment[0]);
+ if (ret)
+ return -ENOENT;
+
+ return 0;
+ }
+#endif
+#ifdef CONFIG_ENV_IS_IN_FAT
+ case ENVL_FAT: {
+ ret = env_fat_init_params(ctx,
+ CONFIG_ENV_FAT_INTERFACE,
+ CONFIG_ENV_FAT_DEVICE_AND_PART,
+ CONFIG_ENV_FAT_FILE);
+
+ return -ENOENT;
+ }
+#endif
+#ifdef CONFIG_ENV_DRV_NONE
+ case ENVL_NOWHERE:
+#ifdef CONFIG_ENV_IS_NOWHERE
+ gd->env_addr = (ulong)&default_environment[0];
+ gd->env_valid = ENV_INVALID;
+
+ return 0;
+#else
+ return -ENOENT;
+#endif
+#endif
+ default:
+ return -ENOENT;
+ }
+}
+
+/*
+ * NOTE: extracted from env/common.c
+ */
+void env_set_ready_uboot(struct env_context *ctx)
+{
+ gd->flags |= GD_FLG_ENV_READY;
+}
+
+bool env_is_ready_uboot(struct env_context *ctx)
+{
+ return (gd->flags & GD_FLG_ENV_READY);
+}
+
+void env_set_valid_uboot(struct env_context *ctx, enum env_valid valid)
+{
+ gd->env_valid = valid;
+}
+
+enum env_valid env_get_valid_uboot(struct env_context *ctx)
+{
+ return gd->env_valid;
+}
+
+void env_set_addr_uboot(struct env_context *ctx, ulong env_addr)
+{
+ gd->env_addr = env_addr;
+}
+
+ulong env_get_addr_uboot(struct env_context *ctx)
+{
+ return gd->env_addr;
+}
+
+/*
+ * Look up the variable from the default environment
+ */
+char *env_get_default_uboot(struct env_context *ctx, const char *name)
+{
+ char *ret_val;
+ unsigned long really_valid = gd->env_valid;
+ unsigned long real_gd_flags = gd->flags;
+
+ /* Pretend that the image is bad. */
+ gd->flags &= ~GD_FLG_ENV_READY;
+ gd->env_valid = ENV_INVALID;
+ ret_val = env_get(ctx, name);
+ gd->env_valid = really_valid;
+ gd->flags = real_gd_flags;
+ return ret_val;
+}
+
+void env_set_default_env_uboot(struct env_context *ctx, const char *s,
+ int flags)
+{
+ if (sizeof(default_environment) > ctx->env_size) {
+ puts("*** Error - default environment is too large\n\n");
+ return;
+ }
+
+ if (s) {
+ if ((flags & H_INTERACTIVE) == 0)
+ printf("*** Warning - %s, using default environment\n\n", s);
+ else
+ puts(s);
+ } else {
+ debug("Using default environment\n");
+ }
+
+ env_htab.ctx = ctx;
+ if (himport_r(&env_htab, (char *)default_environment,
+ sizeof(default_environment), '\0', flags, 0,
+ 0, NULL) == 0)
+ pr_err("## Error: Environment import failed: errno = %d\n",
+ errno);
+
+ gd->flags |= GD_FLG_ENV_READY;
+ gd->flags |= GD_FLG_ENV_DEFAULT;
+}
+
+/* [re]set individual variables to their value in the default environment */
+int env_set_default_vars_uboot(struct env_context *ctx, int nvars,
+ char * const vars[], int flags)
+{
+ /*
+ * Special use-case: import from default environment
+ * (and use \0 as a separator)
+ */
+ flags |= H_NOCLEAR;
+ env_htab.ctx = ctx;
+ return himport_r(&env_htab, (const char *)default_environment,
+ sizeof(default_environment), '\0',
+ flags, 0, nvars, vars);
+}
+
+void env_post_relocate_uboot(struct env_context *ctx)
+{
+ if (gd->env_valid == ENV_INVALID) {
+#if defined(CONFIG_ENV_IS_NOWHERE) || defined(CONFIG_SPL_BUILD)
+ /* Environment not changeable */
+ env_set_default(ctx, NULL, 0);
+#else
+ bootstage_error(BOOTSTAGE_ID_NET_CHECKSUM);
+ env_set_default(ctx, "bad CRC", 0);
+#endif
+ } else {
+ env_load(ctx);
+ }
+}
+
+U_BOOT_ENV_CONTEXT(uboot) = {
+ .name = "uboot",
+ .htab = &env_htab,
+ .env_size = ENV_SIZE,
+ .has_inited = env_has_inited_uboot,
+ .set_inited = env_set_inited_uboot,
+ .get_load_prio = env_get_load_prio_uboot,
+ .get_location = env_get_location_uboot,
+ .get_char_default = env_get_char_default_uboot,
+ .get_char_spec = env_get_char_spec_uboot,
+ .init = env_init_uboot,
+ .drv_init = env_drv_init_uboot,
+ .get_default = env_get_default_uboot,
+ .set_default = env_set_default_env_uboot,
+ .set_default_vars = env_set_default_vars_uboot,
+ .set_ready = env_set_ready_uboot,
+ .is_ready = env_is_ready_uboot,
+ .set_valid = env_set_valid_uboot,
+ .get_valid = env_get_valid_uboot,
+ .set_addr = env_set_addr_uboot,
+ .get_addr = env_get_addr_uboot,
+ .post_relocate = env_post_relocate_uboot,
+};
diff --git a/include/env.h b/include/env.h
index 203605e5e778..26abae2a5c42 100644
--- a/include/env.h
+++ b/include/env.h
@@ -9,6 +9,7 @@
#ifndef __ENV_H
#define __ENV_H
+#include <linker_lists.h>
#include <stdbool.h>
#include <linux/types.h>
@@ -63,6 +64,8 @@ enum env_redund_flags {
ENV_REDUND_ACTIVE = 1,
};
+#define ctx_uboot ll_entry_get(struct env_context, uboot, env_contexts)
+
/* Accessor functions */
void env_set_ready(struct env_context *ctx);
bool env_is_ready(struct env_context *ctx);
--
2.21.0
More information about the U-Boot
mailing list