[U-Boot] [PATCH v4] imx: support i.MX8QM ROM 7720 a1 board
Oliver Graute
oliver.graute at kococonnector.com
Fri Sep 6 09:16:05 UTC 2019
Add i.MX8QM ROM 7720a1 board support
Boot log as below:
U-Boot 2019.10-rc3-00217-g1b7f3d7865 (Sep 06 2019 - 08:03:23 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Advantech iMX8QM Qseven series
Board: ROM-7720-A1 4GB
Build: SCFW 65afe5f6
Boot: SD2
DRAM: 3.9 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial at 5a060000
Out: serial at 5a060000
Err: serial at 5a060000
Net: eth0: ethernet at 5b040000Could not get PHY for FEC1: addr 1
, eth-1: ethernet at 5b050000
Hit any key to stop autoboot: 0
Signed-off-by: Oliver Graute <oliver.graute at kococonnector.com>
Cc: Stefano Babic <sbabic at denx.de>
Cc: Fabio Estevam <festevam at gmail.com>
Cc: Peng Fan <peng.fan at nxp.com>
Cc: Simon Glass <sjg at chromium.org>
Cc: Ye Li <ye.li at nxp.com>
Cc: uboot-imx <uboot-imx at nxp.com>
---
These changes are based on this vendor tree:
https://github.com/ADVANTECH-Corp/uboot-imx6.git
I adapted the files and compared them with code from similar imx8qm-mek board
Changes for v4:
- changed SYS_VENDOR to advantech
- use sc_pm_setup_uart
- removed CONFIG_OF_BOARD_SETUP
- dropped board_gpio_init
- enabled CONFIG_SPL_DM_MMC
- dropped USDHC defines
- dropped CONFIG_AHAB_BOOT
Changes for v3:
- removed duplicate build_info
- removed CONFIG_FSL_ESDHC
Changes for v2:
- cleanup of u-boot environment
- set power mode SC_R_DC_0 for full boot of linux kernel
- enabled usdhc2
- enabled FEC defines
- updated README.md
- enabled readwrite for nfs rootfs
- removed include of environment header
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx8qm-rom7720-a1.dts | 373 ++++++++++++++++++
arch/arm/mach-imx/imx8/Kconfig | 7 +
board/advantech/imx8qm_rom7720_a1/Kconfig | 14 +
board/advantech/imx8qm_rom7720_a1/MAINTAINERS | 6 +
board/advantech/imx8qm_rom7720_a1/Makefile | 11 +
board/advantech/imx8qm_rom7720_a1/README | 70 ++++
.../imx8qm_rom7720_a1/imx8qm_rom7720_a1.c | 141 +++++++
.../advantech/imx8qm_rom7720_a1/imximage.cfg | 21 +
board/advantech/imx8qm_rom7720_a1/spl.c | 223 +++++++++++
configs/imx8qm_rom7720_a1_4G_defconfig | 83 ++++
include/configs/imx8qm_rom7720.h | 176 +++++++++
12 files changed, 1126 insertions(+)
create mode 100644 arch/arm/dts/imx8qm-rom7720-a1.dts
create mode 100644 board/advantech/imx8qm_rom7720_a1/Kconfig
create mode 100644 board/advantech/imx8qm_rom7720_a1/MAINTAINERS
create mode 100644 board/advantech/imx8qm_rom7720_a1/Makefile
create mode 100644 board/advantech/imx8qm_rom7720_a1/README
create mode 100644 board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c
create mode 100644 board/advantech/imx8qm_rom7720_a1/imximage.cfg
create mode 100644 board/advantech/imx8qm_rom7720_a1/spl.c
create mode 100644 configs/imx8qm_rom7720_a1_4G_defconfig
create mode 100644 include/configs/imx8qm_rom7720.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index aac1b83d49..aa139afd57 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -625,6 +625,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
dtb-$(CONFIG_ARCH_IMX8) += \
fsl-imx8qm-apalis.dtb \
fsl-imx8qm-mek.dtb \
+ imx8qm-rom7720-a1.dtb \
fsl-imx8qxp-colibri.dtb \
fsl-imx8qxp-mek.dtb
diff --git a/arch/arm/dts/imx8qm-rom7720-a1.dts b/arch/arm/dts/imx8qm-rom7720-a1.dts
new file mode 100644
index 0000000000..5f9ac955ed
--- /dev/null
+++ b/arch/arm/dts/imx8qm-rom7720-a1.dts
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x80000000 0x00020000;
+
+#include "fsl-imx8qm.dtsi"
+
+/ {
+ model = "Advantech iMX8QM Qseven series";
+ compatible = "fsl,imx8qm-mek", "fsl,imx8qm";
+
+ chosen {
+ bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200";
+ stdout-path = &lpuart0;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+ user {
+ label = "heartbeat";
+ gpios = <&gpio2 15 0>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vmmc: usdhc2_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "sw-3p3-sd1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog_1>;
+
+ imx8qm-mek {
+ pinctrl_hog_1: hoggrp-1 {
+ fsl,pins = <
+ SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03 0x06000048
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0
+ SC_P_ENET0_MDC_CONN_ENET0_MDC 0x06000048
+ SC_P_ENET0_MDIO_CONN_ENET0_MDIO 0x06000048
+ SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x00000060
+ SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x00000060
+ SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x00000060
+ SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x00000060
+ SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x00000060
+ SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x00000060
+ SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x00000060
+ SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x00000060
+ SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x00000060
+ SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x00000060
+ SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x00000060
+ SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x00000060
+ >;
+ };
+
+ pinctrl_fec2: fec2grp {
+ fsl,pins = <
+ SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0
+ SC_P_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000060
+ SC_P_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000060
+ SC_P_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000060
+ SC_P_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000060
+ SC_P_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000060
+ SC_P_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000060
+ SC_P_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000060
+ SC_P_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000060
+ SC_P_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000060
+ SC_P_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000060
+ SC_P_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000060
+ SC_P_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000060
+ >;
+ };
+
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ SC_P_UART0_RX_DMA_UART0_RX 0x06000020
+ SC_P_UART0_TX_DMA_UART0_TX 0x06000020
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000041
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000040
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000040
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21 0x00000021
+ SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22 0x00000021
+ SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041
+ SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021
+ SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021
+ SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021
+ SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021
+ SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021
+ /* WP */
+ SC_P_USDHC2_WP_LSIO_GPIO4_IO11 0x00000021
+ /* CD */
+ SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12 0x00000021
+ >;
+ };
+
+ pinctrl_lpi2c1: lpi2c1grp {
+ fsl,pins = <
+ SC_P_GPT0_CLK_DMA_I2C1_SCL 0x06000020
+ SC_P_GPT0_CAPTURE_DMA_I2C1_SDA 0x06000020
+ /*
+ * Change the default alt function from SCL/SDA to others,
+ * to avoid select input conflict with GPT0
+ */
+ SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03 0x0700004c
+ SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04 0x0700004c
+ SC_P_USB_SS3_TC2_LSIO_GPIO4_IO05 0x0700004c
+ SC_P_USB_SS3_TC3_LSIO_GPIO4_IO06 0x0700004c
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ SC_P_SPDIF0_TX_LSIO_GPIO2_IO15 0x00000021
+ >;
+ };
+ };
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&gpio4 {
+ status = "okay";
+};
+
+&gpio5 {
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <4>;
+ cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy0>;
+ fsl,ar8031-phy-fixup;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec2>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy1>;
+ fsl,ar8031-phy-fixup;
+ fsl,magic-packet;
+ status = "okay";
+};
+
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c1>;
+ status = "okay";
+
+ pca9557_a: gpio at 18 {
+ compatible = "nxp,pca9557";
+ reg = <0x18>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9557_b: gpio at 19 {
+ compatible = "nxp,pca9557";
+ reg = <0x19>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9557_c: gpio at 1b {
+ compatible = "nxp,pca9557";
+ reg = <0x1b>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9557_d: gpio at 1f {
+ compatible = "nxp,pca9557";
+ reg = <0x1f>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&lpuart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart0>;
+ status = "okay";
+};
+
+&lpuart1 {
+ status = "okay";
+};
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig
index bbe323d5ca..eb2eacdfbd 100644
--- a/arch/arm/mach-imx/imx8/Kconfig
+++ b/arch/arm/mach-imx/imx8/Kconfig
@@ -42,6 +42,12 @@ config TARGET_IMX8QM_MEK
select BOARD_LATE_INIT
select IMX8QM
+config TARGET_IMX8QM_ROM7720_A1
+ bool "Support i.MX8QM ROM-7720-A1"
+ select BOARD_LATE_INIT
+ select SUPPORT_SPL
+ select IMX8QM
+
config TARGET_IMX8QXP_MEK
bool "Support i.MX8QXP MEK board"
select BOARD_LATE_INIT
@@ -51,6 +57,7 @@ endchoice
source "board/freescale/imx8qm_mek/Kconfig"
source "board/freescale/imx8qxp_mek/Kconfig"
+source "board/advantech/imx8qm_rom7720_a1/Kconfig"
source "board/toradex/apalis-imx8/Kconfig"
source "board/toradex/colibri-imx8x/Kconfig"
diff --git a/board/advantech/imx8qm_rom7720_a1/Kconfig b/board/advantech/imx8qm_rom7720_a1/Kconfig
new file mode 100644
index 0000000000..cf3869ed92
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_IMX8QM_ROM7720_A1
+
+config SYS_BOARD
+ default "imx8qm_rom7720_a1"
+
+config SYS_VENDOR
+ default "advantech"
+
+config SYS_CONFIG_NAME
+ default "imx8qm_rom7720"
+
+source "board/freescale/common/Kconfig"
+
+endif
diff --git a/board/advantech/imx8qm_rom7720_a1/MAINTAINERS b/board/advantech/imx8qm_rom7720_a1/MAINTAINERS
new file mode 100644
index 0000000000..b142ee02e6
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/MAINTAINERS
@@ -0,0 +1,6 @@
+i.MX8QM ROM 7720 a1 BOARD
+M: Oliver Graute <oliver.graute at kococonnector.com>
+S: Maintained
+F: board/advantech/imx8qm_rom7720_a1/
+F: include/configs/imx8qm_rom7720.h
+F: configs/imx8qm_rom7720_a1_4G_defconfig
diff --git a/board/advantech/imx8qm_rom7720_a1/Makefile b/board/advantech/imx8qm_rom7720_a1/Makefile
new file mode 100644
index 0000000000..51c5de251c
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/Makefile
@@ -0,0 +1,11 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += imx8qm_rom7720_a1.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
diff --git a/board/advantech/imx8qm_rom7720_a1/README b/board/advantech/imx8qm_rom7720_a1/README
new file mode 100644
index 0000000000..eabca8b07a
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/README
@@ -0,0 +1,70 @@
+U-Boot for the NXP i.MX8QM ROM 7720a1 board
+
+Quick Start
+===========
+
+- Build the ARM Trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Get imx-mkimage
+- Build U-Boot
+- Build imx-mkimage
+- Flash the binary into the SD card
+- Boot
+
+Get and Build the ARM Trusted firmware
+======================================
+
+$ git clone https://source.codeaurora.org/external/imx/imx-atf
+$ cd imx-atf/
+$ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga
+$ make PLAT=imx8qm bl31
+
+Get scfw_tcm.bin and ahab-container.img
+==============================
+
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
+$ chmod +x imx-sc-firmware-1.1.bin
+$ ./imx-sc-firmware-1.1.bin
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
+$ chmod +x firmware-imx-8.0.bin
+$ ./firmware-imx-8.0.bin
+
+Build U-Boot
+============
+
+$ export ATF_LOAD_ADDR=0x80000000
+$ export BL33_LOAD_ADDR=0x80020000
+$ make imx8qm_rom7720_a1_4G_defconfig
+$ make flash.bin
+$ dd if=u-boot.itb of=flash.bin bs=512 seek=854
+
+Get imx-mkimage
+==============================
+
+$ git clone https://source.codeaurora.org/external/imx/imx-mkimage/
+$ cd imx-mkimage
+$ git checkout rel_imx_4.14.78_1.0.0_ga -b rel_imx_4.14.78_1.0.0_ga
+$ cd iMX8QM/
+
+Copy the following binaries to iMX8QM folder:
+
+$ cp imx-atf/build/imx8qm/release/bl31.bin .
+$ cp u-boot/u-boot.bin .
+
+Copy the following firmwares U-Boot folder :
+
+$ cp firmware-imx-8.0/firmware/seco/mx8qm-ahab-container.img .
+$ cp imx-sc-firmware-1.1/mx8qm-val-scfw-tcm.bin scfw_tcm.bin
+
+$ make SOC=iMX8QM flash_linux_m4
+
+Flash the binary into the SD card
+=================================
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync
+
+Boot
+====
+Set Boot switch SW2: 1100.
diff --git a/board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c b/board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c
new file mode 100644
index 0000000000..2f97d5ce96
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ * Copyright (C) 2019 Oliver Graute <oliver.graute at kococonnector.com>
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart0_pads[] = {
+ SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
+}
+
+int board_early_init_f(void)
+{
+ sc_pm_clock_rate_t rate = SC_80MHZ;
+ int ret;
+
+ /* Set UART0 clock root to 80 MHz */
+ ret = sc_pm_setup_uart(SC_R_UART_0, rate);
+ if (ret)
+ return ret;
+
+ setup_iomux_uart();
+
+ /* This is needed to because Kernel do not Power Up DC_0 */
+ sc_pm_set_resource_power_mode(-1, SC_R_DC_0, SC_PM_PW_MODE_ON);
+ sc_pm_set_resource_power_mode(-1, SC_R_GPIO_5, SC_PM_PW_MODE_ON);
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_FEC_MXC)
+#include <miiphy.h>
+
+int board_phy_config(struct phy_device *phydev)
+{
+#ifdef CONFIG_FEC_ENABLE_MAX7322
+ u8 value;
+
+ /* This is needed to drive the pads to 1.8V instead of 1.5V */
+ i2c_set_bus_num(CONFIG_MAX7322_I2C_BUS);
+
+ if (!i2c_probe(CONFIG_MAX7322_I2C_ADDR)) {
+ /* Write 0x1 to enable O0 output, this device has no addr */
+ /* hence addr length is 0 */
+ value = 0x1;
+ if (dm_i2c_write(CONFIG_MAX7322_I2C_ADDR, 0, 0, &value, 1))
+ printf("MAX7322 write failed\n");
+ } else {
+ printf("MAX7322 Not found\n");
+ }
+ mdelay(1);
+#endif
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif
+
+int checkboard(void)
+{
+ puts("Board: ROM-7720-A1 4GB\n");
+
+ build_info();
+ print_bootinfo();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Power up base board */
+ sc_pm_set_resource_power_mode(-1, SC_R_BOARD_R1, SC_PM_PW_MODE_ON);
+
+ return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+ puts("\nDDR ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+ /* TODO */
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+ return devno;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ env_set("board_name", "ROM-7720-A1");
+ env_set("board_rev", "iMX8QM");
+#endif
+
+ env_set("sec_boot", "no");
+#ifdef CONFIG_AHAB_BOOT
+ env_set("sec_boot", "yes");
+#endif
+
+ return 0;
+}
diff --git a/board/advantech/imx8qm_rom7720_a1/imximage.cfg b/board/advantech/imx8qm_rom7720_a1/imximage.cfg
new file mode 100644
index 0000000000..e324c7ca37
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/imximage.cfg
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-val-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000
diff --git a/board/advantech/imx8qm_rom7720_a1/spl.c b/board/advantech/imx8qm_rom7720_a1/spl.c
new file mode 100644
index 0000000000..4166524656
--- /dev/null
+++ b/board/advantech/imx8qm_rom7720_a1/spl.c
@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ */
+#include <common.h>
+#include <dm.h>
+#include <spl.h>
+#include <fsl_esdhc.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ESDHC_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ESDHC_CLK_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_INPUT_PAD_CTRL ((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_NORMAL_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define FSPI_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define I2C_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC1_CD_GPIO IMX_GPIO_NR(5, 22)
+#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 12)
+
+static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
+ {USDHC1_BASE_ADDR, 0, 8},
+ {USDHC2_BASE_ADDR, 0, 4},
+ {USDHC3_BASE_ADDR, 0, 4},
+};
+
+static iomux_cfg_t emmc0[] = {
+ SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+ SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc2_sd[] = {
+ SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+ SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_WP | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+int board_mmc_init(bd_t *bis)
+{
+ int i, ret;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-Boot device node) (Physical Port)
+ * mmc0 USDHC1
+ * mmc1 USDHC2
+ * mmc2 USDHC3
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_SDHC_0, SC_PM_PW_MODE_ON);
+ if (ret != SC_ERR_NONE)
+ return ret;
+
+ imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0));
+ init_clk_usdhc(0);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ case 1:
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_SDHC_2, SC_PM_PW_MODE_ON);
+ if (ret != SC_ERR_NONE)
+ return ret;
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_GPIO_4, SC_PM_PW_MODE_ON);
+ if (ret != SC_ERR_NONE)
+ return ret;
+
+ imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd));
+ init_clk_usdhc(2);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ gpio_request(USDHC2_CD_GPIO, "sd2_cd");
+ gpio_direction_input(USDHC2_CD_GPIO);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) than supported by the board\n", i + 1);
+ return 0;
+ }
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = 1;
+ break;
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+#endif /* CONFIG_FSL_ESDHC */
+
+void spl_board_init(void)
+{
+#if defined(CONFIG_SPL_SPI_SUPPORT)
+ if (sc_rm_is_resource_owned(-1, SC_R_FSPI_0)) {
+ if (sc_pm_set_resource_power_mode(-1, SC_R_FSPI_0, SC_PM_PW_MODE_ON)) {
+ puts("Warning: failed to initialize FSPI0\n");
+ }
+ }
+#endif
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ puts("Normal Boot\n");
+}
+
+void spl_board_prepare_for_boot(void)
+{
+#if defined(CONFIG_SPL_SPI_SUPPORT)
+ if (sc_rm_is_resource_owned(-1, SC_R_FSPI_0)) {
+ if (sc_pm_set_resource_power_mode(-1, SC_R_FSPI_0, SC_PM_PW_MODE_OFF)) {
+ puts("Warning: failed to turn off FSPI0\n");
+ }
+ }
+#endif
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+ /* Just empty function now - can't decide what to choose */
+ debug("%s: %s\n", __func__, name);
+
+ return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+ /* Clear global data */
+ memset((void *)gd, 0, sizeof(gd_t));
+
+ arch_cpu_init();
+
+ board_early_init_f();
+
+ timer_init();
+
+ preloader_console_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ board_init_r(NULL, 0);
+}
diff --git a/configs/imx8qm_rom7720_a1_4G_defconfig b/configs/imx8qm_rom7720_a1_4G_defconfig
new file mode 100644
index 0000000000..bbecea8e61
--- /dev/null
+++ b/configs/imx8qm_rom7720_a1_4G_defconfig
@@ -0,0 +1,83 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_ICACHE_OFF=y
+CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_ARCH_IMX8=y
+CONFIG_SYS_TEXT_BASE=0x80020000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_IMX8QM_ROM7720_A1=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=4
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/advantech/imx8qm_rom7720_a1/imximage.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_LOG=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_CPU=y
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_FAT=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx8qm-rom7720-a1"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_MMC=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_IMX8=y
+CONFIG_CPU=y
+CONFIG_DM_GPIO=y
+CONFIG_MXC_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_IMX_LPI2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_ESDHC_IMX=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_FEC_MXC_SHARE_MDIO=y
+CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX8=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_SPL_TINY_MEMSET=y
+# CONFIG_EFI_LOADER is not set
+CONFIG_ARCH_MISC_INIT
+CONFIG_NET_RANDOM_ETHADDR=y
diff --git a/include/configs/imx8qm_rom7720.h b/include/configs/imx8qm_rom7720.h
new file mode 100644
index 0000000000..a9a0eb102b
--- /dev/null
+++ b/include/configs/imx8qm_rom7720.h
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ */
+
+#ifndef __IMX8QM_ROM7720_H
+#define __IMX8QM_ROM7720_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+#define CONFIG_REMAKE_ELF
+
+#undef CONFIG_BOOTM_NETBSD
+
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+/* FUSE command */
+#define CONFIG_CMD_FUSE
+
+/* Boot M4 */
+#define M4_BOOT_ENV \
+ "m4_0_image=m4_0.bin\0" \
+ "m4_1_image=m4_1.bin\0" \
+ "loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_0_image}\0" \
+ "loadm4image_1=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_1_image}\0" \
+ "m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \
+ "m4boot_1=run loadm4image_1; dcache flush; bootaux ${loadaddr} 1\0" \
+
+#ifdef CONFIG_NAND_BOOT
+#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:128m(boot),32m(kernel),16m(dtb),8m(misc),-(rootfs) "
+#else
+#define MFG_NAND_PARTITION ""
+#endif
+
+#define CONFIG_MFG_ENV_SETTINGS \
+ "mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+ "rdinit=/linuxrc " \
+ "g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+ "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+ "g_mass_storage.iSerialNumber=\"\" "\
+ MFG_NAND_PARTITION \
+ "clk_ignore_unused "\
+ "\0" \
+ "initrd_addr=0x83800000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_MFG_ENV_SETTINGS \
+ M4_BOOT_ENV \
+ "script=boot.scr\0" \
+ "image=Image\0" \
+ "panel=NULL\0" \
+ "console=ttyLP0\0" \
+ "fdt_addr=0x83000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "boot_fdt=try\0" \
+ "fdt_file=imx8qm-rom7720-a1.dtb\0" \
+ "initrd_addr=0x83800000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} earlycon\0 " \
+ "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "echo wait for boot; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp rw earlycon\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${loadaddr} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "booti; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR 0x80280000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
+
+/* Default environment is in SD */
+#define CONFIG_ENV_SIZE 0x2000
+
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_ENV_OFFSET (4 * 1024 * 1024)
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#else
+#define CONFIG_ENV_OFFSET (64 * SZ_64K)
+#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
+#endif
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+
+/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board,
+ * USDHC3 is for SD on base board On DDR4 board, USDHC1 is mux for NAND,
+ * USDHC2 is for SD, USDHC3 is for SD on base board
+ */
+#define CONFIG_SYS_MMC_ENV_DEV 2 /* USDHC3 */
+#define CONFIG_MMCROOT "/dev/mmcblk2p2" /* USDHC3 */
+#define CONFIG_SYS_FSL_USDHC_NUM 3
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define PHYS_SDRAM_1 0x80000000
+#define PHYS_SDRAM_2 0x880000000
+#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
+/* LPDDR4 board total DDR is 6GB, DDR4 board total DDR is 4 GB */
+#define PHYS_SDRAM_2_SIZE 0x80000000 /* 2 GB */
+
+#define CONFIG_SYS_MEMTEST_START 0xA0000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (PHYS_SDRAM_1_SIZE >> 2))
+
+/* Serial */
+#define CONFIG_BAUDRATE 115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 8000000 /* 8MHz */
+
+/* Networking */
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define FEC_QUIRK_ENET_MAC
+
+#endif /* __IMX8QM_ROM7720_H */
--
2.17.1
More information about the U-Boot
mailing list