[U-Boot] [PATCH v2 00/28] Add and update drivers for MediaTek MT76x8 SoCs

[Weijie Gao]

This patch series have the following changes:

- Add pinctrl(both pinmux and pinconf) driver, reset controller driver and
   clock driver for mt7628.
- Add mt7628 platform to mtk-sd driver.
- Modify mt7628's ethernet & usb phy driver to take advantages from the new
   drivers.
- Update mt7621-spi driver with a new transfer method.
- Enable fifo, disable flow control, and enable non-DM implementation for mtk
   hsuart driver.
- Enanble the new drivers for currently existed mt7628 boards.

Changes of v2:
- Change clock gateing driver to a more 'generic' driver which supports output
  clock rates of CPU/SYS_BUS/peripherals.
- mt7621-spi now uses accurate sys_freq from clock driver.
- Make PHY link detection optional via DT.
- Select essential drivers in Kconfig instead of setting in defconfig files.

Weijie Gao (28):
  serial: serial_mtk: enable FIFO and disable flow control
  serial: serial_mtk: add non-DM version for SPL
  dts: mtmips: move uart property clock-frequency into mt7628an.dtsi
  dts: mtmips: enable high-speed UART support for mt7628
  clk: add clock driver for MediaTek MT76x8 platform
  dts: mtmips: add clock node for mt7628
  spi: mt7621-spi: use clock frequency from clk driver
  spi: mt7621-spi: remove data cache and rewrite its xfer function
  spi: mt7621-spi: restore default register value after each xfer
  pinctrl: add support for MediaTek MT7628
  dts: mtmips: add pinctrl node for mt7628
  dts: mtmips: add default pinctrl for uart nodes
  reset: add reset controller driver for MediaTek MIPS platform
  dts: mtmips: update reset controller node for mt7628
  phy: mt76x8-usb-phy: add slew rate calibration and remove non-mt7628
    part
  net: mt7628-eth: remove hardcoded gpio settings and regmap-based phy
    reset
  net: mt7628-eth: make phy link up detection optional via DT
  net: mt7628-eth: free rx descriptor on receiving failure
  net: mt7628-eth: add support to isolate LAN/WAN ports
  dts: mtmips: enable eth port0 led and link poll functions for all
    boards
  mmc: mtk-sd: add support for MediaTek MT7620/MT7628 SoCs
  mmc: mtk-sd: add a dts property cd-active-high for builtin-cd mode
  dts: mtmips: add mmc related nodes for mt7628an.dtsi
  dts: mtmips: add default pinctrl for gardena-smart-gateway-mt7688
  dts: mtmips: add default pinctrl to eth nodes for all boards
  mips: mtmips: change baudrate table for all boards
  mips: mtmips: select essential drivers in Kconfig
  configs: mtmips: remove configs which are selected in Kconfig or
    useless

 arch/mips/Kconfig                             |   6 +
 .../mips/dts/gardena-smart-gateway-mt7688.dts |  19 +-
 arch/mips/dts/linkit-smart-7688.dts           |  16 +-
 arch/mips/dts/mt7628a.dtsi                    | 246 +++++++-
 arch/mips/mach-mtmips/Kconfig                 |   2 +
 ...gardena-smart-gateway-mt7688-ram_defconfig |   7 -
 .../gardena-smart-gateway-mt7688_defconfig    |   7 -
 configs/linkit-smart-7688-ram_defconfig       |   7 -
 configs/linkit-smart-7688_defconfig           |   7 -
 drivers/clk/Makefile                          |   1 +
 drivers/clk/mtmips/Makefile                   |   3 +
 drivers/clk/mtmips/clk-mt7628.c               | 158 +++++
 drivers/mmc/Kconfig                           |   2 +-
 drivers/mmc/mtk-sd.c                          |  32 +-
 drivers/net/Kconfig                           |   1 +
 drivers/net/mt7628-eth.c                      | 135 ++--
 drivers/phy/Kconfig                           |   2 +
 drivers/phy/mt76x8-usb-phy.c                  | 225 +++++--
 drivers/pinctrl/Kconfig                       |   1 +
 drivers/pinctrl/Makefile                      |   1 +
 drivers/pinctrl/mtmips/Kconfig                |  13 +
 drivers/pinctrl/mtmips/Makefile               |   7 +
 drivers/pinctrl/mtmips/pinctrl-mt7628.c       | 585 ++++++++++++++++++
 .../pinctrl/mtmips/pinctrl-mtmips-common.c    |  87 +++
 .../pinctrl/mtmips/pinctrl-mtmips-common.h    |  53 ++
 drivers/reset/Kconfig                         |   7 +
 drivers/reset/Makefile                        |   1 +
 drivers/reset/reset-mtmips.c                  |  82 +++
 drivers/serial/serial.c                       |   2 +
 drivers/serial/serial_mtk.c                   | 223 ++++++-
 drivers/spi/mt7621_spi.c                      | 247 ++++----
 .../configs/gardena-smart-gateway-mt7688.h    |   2 +-
 include/configs/linkit-smart-7688.h           |   2 +-
 include/dt-bindings/clock/mt7628-clk.h        |  37 ++
 include/dt-bindings/reset/mt7628-reset.h      |  36 ++
 35 files changed, 1933 insertions(+), 329 deletions(-)
 create mode 100644 drivers/clk/mtmips/Makefile
 create mode 100644 drivers/clk/mtmips/clk-mt7628.c
 create mode 100644 drivers/pinctrl/mtmips/Kconfig
 create mode 100644 drivers/pinctrl/mtmips/Makefile
 create mode 100644 drivers/pinctrl/mtmips/pinctrl-mt7628.c
 create mode 100644 drivers/pinctrl/mtmips/pinctrl-mtmips-common.c
 create mode 100644 drivers/pinctrl/mtmips/pinctrl-mtmips-common.h
 create mode 100644 drivers/reset/reset-mtmips.c
 create mode 100644 include/dt-bindings/clock/mt7628-clk.h
 create mode 100644 include/dt-bindings/reset/mt7628-reset.h

-- 
2.17.1