[PATCH] ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Peter Robinson
pbrobinson at gmail.com
Thu Apr 2 00:31:02 CEST 2020
On Wed, Mar 25, 2020 at 6:22 PM <tomcwarren3959 at gmail.com> wrote:
>
> From: Tom Warren <twarren at nvidia.com>
>
> The Jetson Nano Developer Kit is a Tegra X1-based development board. It
> is similar to Jetson TX1 but it is not pin compatible. It features 4GB
> of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
> used for storage.
>
> HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
> and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
> Ethernet controller provides onboard network connectivity. NVMe support
> has also been added. Env save is at the end of QSPI (4MB-8K).
>
> A 40-pin header on the board can be used to extend the capabilities and
> exposed interfaces of the Jetson Nano.
>
> Signed-off-by: Thierry Reding <treding at nvidia.com>
> Signed-off-by: Tom Warren <twarren at nvidia.com>
Tested-by: Peter Robinson <pbrobinson at gmail.com>
Tested with L4T R32.3.1 and Fedora 32. A query below.
> ---
> retry send-email to see if it shows up in Patchwork
>
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/tegra210-p3450-0000.dts | 147 +++++++++++++++++++++++++++++
> arch/arm/mach-tegra/board2.c | 25 +++++
> arch/arm/mach-tegra/tegra210/Kconfig | 7 ++
> board/nvidia/p3450-0000/Kconfig | 12 +++
> board/nvidia/p3450-0000/MAINTAINERS | 6 ++
> board/nvidia/p3450-0000/Makefile | 8 ++
> board/nvidia/p3450-0000/p3450-0000.c | 178 +++++++++++++++++++++++++++++++++++
> configs/p3450-0000_defconfig | 64 +++++++++++++
> include/configs/p3450-0000.h | 46 +++++++++
> 10 files changed, 495 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/tegra210-p3450-0000.dts
> create mode 100644 board/nvidia/p3450-0000/Kconfig
> create mode 100644 board/nvidia/p3450-0000/MAINTAINERS
> create mode 100644 board/nvidia/p3450-0000/Makefile
> create mode 100644 board/nvidia/p3450-0000/p3450-0000.c
> create mode 100644 configs/p3450-0000_defconfig
> create mode 100644 include/configs/p3450-0000.h
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 9c593b2..820ee97 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -180,7 +180,8 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
> tegra210-e2220-1170.dtb \
> tegra210-p2371-0000.dtb \
> tegra210-p2371-2180.dtb \
> - tegra210-p2571.dtb
> + tegra210-p2571.dtb \
> + tegra210-p3450-0000.dtb
>
> dtb-$(CONFIG_ARCH_MVEBU) += \
> armada-3720-db.dtb \
> diff --git a/arch/arm/dts/tegra210-p3450-0000.dts b/arch/arm/dts/tegra210-p3450-0000.dts
> new file mode 100644
> index 0000000..9ef744a
> --- /dev/null
> +++ b/arch/arm/dts/tegra210-p3450-0000.dts
> @@ -0,0 +1,147 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2019-2020 NVIDIA Corporation <www.nvidia.com>
> + */
> +/dts-v1/;
> +
> +#include "tegra210.dtsi"
> +
> +/ {
> + model = "NVIDIA Jetson Nano Developer Kit";
> + compatible = "nvidia,p3450-0000", "nvidia,tegra210";
> +
> + chosen {
> + stdout-path = &uarta;
> + };
> +
> + aliases {
> + ethernet = "/pcie at 1003000/pci at 2,0/ethernet at 0,0";
> + i2c0 = "/i2c at 7000d000";
> + i2c2 = "/i2c at 7000c400";
> + i2c3 = "/i2c at 7000c500";
> + i2c4 = "/i2c at 7000c700";
> + mmc0 = "/sdhci at 700b0600";
> + mmc1 = "/sdhci at 700b0000";
> + spi0 = "/spi at 70410000";
> + usb0 = "/usb at 7d000000";
> + };
> +
> + memory {
> + reg = <0x0 0x80000000 0x0 0xc0000000>;
> + };
> +
> + pcie at 1003000 {
> + status = "okay";
> +
> + pci at 1,0 {
> + status = "okay";
> + };
> +
> + pci at 2,0 {
> + status = "okay";
> +
> + ethernet at 0,0 {
> + reg = <0x000000 0 0 0 0>;
> + local-mac-address = [ 00 00 00 00 00 00 ];
> + };
> + };
> + };
> +
> + serial at 70006000 {
> + status = "okay";
> + };
> +
> + padctl at 7009f000 {
> + pinctrl-0 = <&padctl_default>;
> + pinctrl-names = "default";
> +
> + padctl_default: pinmux {
> + xusb {
> + nvidia,lanes = "otg-1", "otg-2";
> + nvidia,function = "xusb";
> + nvidia,iddq = <0>;
> + };
> +
> + usb3 {
> + nvidia,lanes = "pcie-5", "pcie-6";
> + nvidia,function = "usb3";
> + nvidia,iddq = <0>;
> + };
> +
> + pcie-x1 {
> + nvidia,lanes = "pcie-0";
> + nvidia,function = "pcie-x1";
> + nvidia,iddq = <0>;
> + };
> +
> + pcie-x4 {
> + nvidia,lanes = "pcie-1", "pcie-2",
> + "pcie-3", "pcie-4";
> + nvidia,function = "pcie-x4";
> + nvidia,iddq = <0>;
> + };
> +
> + sata {
> + nvidia,lanes = "sata-0";
> + nvidia,function = "sata";
> + nvidia,iddq = <0>;
> + };
> + };
> + };
> +
> + sdhci at 700b0000 {
> + status = "okay";
> + cd-gpios = <&gpio TEGRA_GPIO(Z, 1) GPIO_ACTIVE_LOW>;
> + power-gpios = <&gpio TEGRA_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + bus-width = <4>;
> + };
> +
> + sdhci at 700b0600 {
> + status = "okay";
> + bus-width = <8>;
> + non-removable;
> + };
> +
> + i2c at 7000c400 {
> + status = "okay";
> + clock-frequency = <400000>;
> + };
> +
> + i2c at 7000c500 {
> + status = "okay";
> + clock-frequency = <400000>;
> + };
> +
> + i2c at 7000c700 {
> + status = "okay";
> + clock-frequency = <400000>;
> + };
> +
> + i2c at 7000d000 {
> + status = "okay";
> + clock-frequency = <400000>;
> + };
> +
> + spi at 70410000 {
> + status = "okay";
> + spi-max-frequency = <80000000>;
> + };
> +
> + usb at 7d000000 {
> + status = "okay";
> + dr_mode = "peripheral";
> + };
> +
> + clocks {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + clk32k_in: clock at 0 {
> + compatible = "fixed-clock";
> + reg = <0>;
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + };
> + };
> +};
> diff --git a/arch/arm/mach-tegra/board2.c b/arch/arm/mach-tegra/board2.c
> index 787ff97..224efc9 100644
> --- a/arch/arm/mach-tegra/board2.c
> +++ b/arch/arm/mach-tegra/board2.c
> @@ -217,6 +217,31 @@ int board_early_init_f(void)
> arch_timer_init();
> #endif
>
> +#if defined(CONFIG_DISABLE_SDMMC1_EARLY)
> + /*
> + * Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT.
> + * We do this because earlier bootloaders have enabled power to
> + * SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init()
> + * results in power being back-driven into the SD-card and SDMMC1
> + * HW, which is 'bad' as per the HW team.
> + *
> + * From the HW team: "LDO2 from the PMIC has already been set to 3.3v in
> + * nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT
> + * table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off
> + * the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard
> + * voltage turns off. Since the SDCard voltage is no longer there, the
> + * SDMMC CLK/DAT lines are backdriving into what essentially is a
> + * powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V"
> + *
> + * Note that this can probably be removed when we change over to storing
> + * all BL components on QSPI on Nano, and U-Boot then becomes the first
> + * one to turn on SDMMC1 power. Another fix would be to have CBoot
> + * disable power/gate SDMMC1 off before handing off to U-Boot/kernel.
> + */
> + reset_set_enable(PERIPH_ID_SDMMC1, 1);
> + clock_set_enable(PERIPH_ID_SDMMC1, 0);
> +#endif /* CONFIG_DISABLE_SDMMC1_EARLY */
> +
> pinmux_init();
> board_init_uart_f();
>
> diff --git a/arch/arm/mach-tegra/tegra210/Kconfig b/arch/arm/mach-tegra/tegra210/Kconfig
> index 3637473..97ed8e0 100644
> --- a/arch/arm/mach-tegra/tegra210/Kconfig
> +++ b/arch/arm/mach-tegra/tegra210/Kconfig
> @@ -35,6 +35,12 @@ config TARGET_P2571
> help
> P2571 is a P2530 married to a P1963 I/O board
>
> +config TARGET_P3450_0000
> + bool "NVIDIA Jetson Nano Developer Kit"
> + select BOARD_LATE_INIT
> + help
> + P3450-0000 is a P3448 CPU board married to a P3449 I/O board.
> +
> endchoice
>
> config SYS_SOC
> @@ -44,5 +50,6 @@ source "board/nvidia/e2220-1170/Kconfig"
> source "board/nvidia/p2371-0000/Kconfig"
> source "board/nvidia/p2371-2180/Kconfig"
> source "board/nvidia/p2571/Kconfig"
> +source "board/nvidia/p3450-0000/Kconfig"
>
> endif
> diff --git a/board/nvidia/p3450-0000/Kconfig b/board/nvidia/p3450-0000/Kconfig
> new file mode 100644
> index 0000000..7a08cd8
> --- /dev/null
> +++ b/board/nvidia/p3450-0000/Kconfig
> @@ -0,0 +1,12 @@
> +if TARGET_P3450_0000
> +
> +config SYS_BOARD
> + default "p3450-0000"
> +
> +config SYS_VENDOR
> + default "nvidia"
> +
> +config SYS_CONFIG_NAME
> + default "p3450-0000"
> +
> +endif
> diff --git a/board/nvidia/p3450-0000/MAINTAINERS b/board/nvidia/p3450-0000/MAINTAINERS
> new file mode 100644
> index 0000000..4070006
> --- /dev/null
> +++ b/board/nvidia/p3450-0000/MAINTAINERS
> @@ -0,0 +1,6 @@
> +P3450-0000 BOARD
> +M: Tom Warren <twarren at nvidia.com>
> +S: Maintained
> +F: board/nvidia/p3450-0000/
> +F: include/configs/p3450-0000.h
> +F: configs/p3450-0000_defconfig
> diff --git a/board/nvidia/p3450-0000/Makefile b/board/nvidia/p3450-0000/Makefile
> new file mode 100644
> index 0000000..993c506
> --- /dev/null
> +++ b/board/nvidia/p3450-0000/Makefile
> @@ -0,0 +1,8 @@
> +#
> +# (C) Copyright 2018
> +# NVIDIA Corporation <www.nvidia.com>
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y += p3450-0000.o
> diff --git a/board/nvidia/p3450-0000/p3450-0000.c b/board/nvidia/p3450-0000/p3450-0000.c
> new file mode 100644
> index 0000000..f4212ab
> --- /dev/null
> +++ b/board/nvidia/p3450-0000/p3450-0000.c
> @@ -0,0 +1,178 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2018-2019
> + * NVIDIA Corporation <www.nvidia.com>
> + *
> + */
> +
> +#include <common.h>
> +#include <fdtdec.h>
> +#include <i2c.h>
> +#include <linux/libfdt.h>
> +#include <pca953x.h>
> +#include <asm/arch-tegra/cboot.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/pinmux.h>
> +#include "../p2571/max77620_init.h"
> +
> +void pin_mux_mmc(void)
> +{
> + struct udevice *dev;
> + uchar val;
> + int ret;
> +
> + /* Turn on MAX77620 LDO2 to 3.3V for SD card power */
> + debug("%s: Set LDO2 for VDDIO_SDMMC_AP power to 3.3V\n", __func__);
> + ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
> + if (ret) {
> + printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
> + return;
> + }
> + /* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
> + val = 0xF2;
> + ret = dm_i2c_write(dev, MAX77620_CNFG1_L2_REG, &val, 1);
> + if (ret)
> + printf("i2c_write 0 0x3c 0x27 failed: %d\n", ret);
> +
> + /* Disable LDO4 discharge */
> + ret = dm_i2c_read(dev, MAX77620_CNFG2_L4_REG, &val, 1);
> + if (ret) {
> + printf("i2c_read 0 0x3c 0x2c failed: %d\n", ret);
> + } else {
> + val &= ~BIT(1); /* ADE */
> + ret = dm_i2c_write(dev, MAX77620_CNFG2_L4_REG, &val, 1);
> + if (ret)
> + printf("i2c_write 0 0x3c 0x2c failed: %d\n", ret);
> + }
> +
> + /* Set MBLPD */
> + ret = dm_i2c_read(dev, MAX77620_CNFGGLBL1_REG, &val, 1);
> + if (ret) {
> + printf("i2c_write 0 0x3c 0x00 failed: %d\n", ret);
> + } else {
> + val |= BIT(6); /* MBLPD */
> + ret = dm_i2c_write(dev, MAX77620_CNFGGLBL1_REG, &val, 1);
> + if (ret)
> + printf("i2c_write 0 0x3c 0x00 failed: %d\n", ret);
> + }
> +}
> +
> +#ifdef CONFIG_PCI_TEGRA
> +int tegra_pcie_board_init(void)
> +{
> + struct udevice *dev;
> + uchar val;
> + int ret;
> +
> + /* Turn on MAX77620 LDO1 to 1.05V for PEX power */
> + debug("%s: Set LDO1 for PEX power to 1.05V\n", __func__);
> + ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
> + if (ret) {
> + printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
> + return -1;
> + }
> + /* 0xCA for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
> + val = 0xCA;
> + ret = dm_i2c_write(dev, MAX77620_CNFG1_L1_REG, &val, 1);
> + if (ret)
> + printf("i2c_write 0 0x3c 0x25 failed: %d\n", ret);
> +
> + return 0;
> +}
> +#endif /* PCI */
> +
> +static void ft_mac_address_setup(void *fdt)
> +{
> + const void *cboot_fdt = (const void *)cboot_boot_x0;
> + uint8_t mac[ETH_ALEN], local_mac[ETH_ALEN];
> + const char *path;
> + int offset, err;
> +
> + err = cboot_get_ethaddr(cboot_fdt, local_mac);
> + if (err < 0)
> + memset(local_mac, 0, ETH_ALEN);
> +
> + path = fdt_get_alias(fdt, "ethernet");
> + if (!path)
> + return;
> +
> + debug("ethernet alias found: %s\n", path);
> +
> + offset = fdt_path_offset(fdt, path);
> + if (offset < 0) {
> + printf("ethernet alias points to absent node %s\n", path);
> + return;
> + }
> +
> + if (is_valid_ethaddr(local_mac)) {
> + err = fdt_setprop(fdt, offset, "local-mac-address", local_mac,
> + ETH_ALEN);
> + if (!err)
> + debug("Local MAC address set: %pM\n", local_mac);
> + }
> +
> + if (eth_env_get_enetaddr("ethaddr", mac)) {
> + if (memcmp(local_mac, mac, ETH_ALEN) != 0) {
> + err = fdt_setprop(fdt, offset, "mac-address", mac,
> + ETH_ALEN);
> + if (!err)
> + debug("MAC address set: %pM\n", mac);
> + }
> + }
> +}
> +
> +static int ft_copy_carveout(void *dst, const void *src, const char *node)
> +{
> + struct fdt_memory fb;
> + int err;
> +
> + err = fdtdec_get_carveout(src, node, "memory-region", 0, &fb);
> + if (err < 0) {
> + if (err != -FDT_ERR_NOTFOUND)
> + printf("failed to get carveout for %s: %d\n", node,
> + err);
> +
> + return err;
> + }
> +
> + err = fdtdec_set_carveout(dst, node, "memory-region", 0, "framebuffer",
> + &fb);
> + if (err < 0) {
> + printf("failed to set carveout for %s: %d\n", node, err);
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +static void ft_carveout_setup(void *fdt)
> +{
> + const void *cboot_fdt = (const void *)cboot_boot_x0;
> + static const char * const nodes[] = {
> + "/host1x at 50000000/dc at 54200000",
> + "/host1x at 50000000/dc at 54240000",
> + };
> + unsigned int i;
> + int err;
> +
> + for (i = 0; i < ARRAY_SIZE(nodes); i++) {
> + printf("copying carveout for %s...\n", nodes[i]);
> +
> + err = ft_copy_carveout(fdt, cboot_fdt, nodes[i]);
> + if (err < 0) {
> + if (err != -FDT_ERR_NOTFOUND)
> + printf("failed to copy carveout for %s: %d\n",
> + nodes[i], err);
> +
> + continue;
> + }
> + }
> +}
> +
> +int ft_board_setup(void *fdt, bd_t *bd)
> +{
> + ft_mac_address_setup(fdt);
> + ft_carveout_setup(fdt);
> +
> + return 0;
> +}
> diff --git a/configs/p3450-0000_defconfig b/configs/p3450-0000_defconfig
> new file mode 100644
> index 0000000..c861d13
> --- /dev/null
> +++ b/configs/p3450-0000_defconfig
> @@ -0,0 +1,64 @@
> +CONFIG_ARM=y
> +CONFIG_TEGRA=y
> +CONFIG_SYS_TEXT_BASE=0x80080000
> +CONFIG_TEGRA210=y
> +CONFIG_TARGET_P3450_0000=y
> +CONFIG_NR_DRAM_BANKS=2
> +CONFIG_OF_SYSTEM_SETUP=y
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_CONSOLE_MUX=y
> +CONFIG_SYS_STDIO_DEREGISTER=y
> +CONFIG_SYS_PROMPT="Tegra210 (P3450-0000) # "
> +# CONFIG_CMD_IMI is not set
> +CONFIG_CMD_DFU=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_PCI=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +# CONFIG_CMD_SETEXPR is not set
> +# CONFIG_CMD_NFS is not set
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_OF_LIVE=y
> +CONFIG_DEFAULT_DEVICE_TREE="tegra210-p3450-0000"
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_DFU_SF=y
> +CONFIG_SYS_I2C_TEGRA=y
> +CONFIG_SPI_FLASH=y
> +CONFIG_SPI_FLASH_MACRONIX=y
> +CONFIG_SPI_FLASH_USE_4K_SECTORS=y
> +CONFIG_SF_DEFAULT_MODE=0
> +CONFIG_SF_DEFAULT_SPEED=24000000
> +CONFIG_RTL8169=y
> +CONFIG_PCI=y
> +CONFIG_DM_PCI=y
> +CONFIG_DM_PCI_COMPAT=y
> +CONFIG_PCI_TEGRA=y
> +CONFIG_SYS_NS16550=y
> +CONFIG_TEGRA114_SPI=y
> +CONFIG_TEGRA210_QSPI=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_TEGRA=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="NVIDIA"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x0955
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x701a
> +CONFIG_CI_UDC=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +# CONFIG_ENV_IS_IN_MMC is not set
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_ENV_SIZE=0x2000
> +CONFIG_ENV_SECT_SIZE=0x1000
> +CONFIG_ENV_OFFSET=0xFFFFE000
> +CONFIG_BOOTP_PREFER_SERVERIP=y
> +CONFIG_DISABLE_SDMMC1_EARLY=y
> +CONFIG_NVME=y
Should it also have the following that was added for the other
tegra210 Jetson that you sent through with one of hte other t210 patch
series?
CONFIG_POSITION_INDEPENDENT=y
> diff --git a/include/configs/p3450-0000.h b/include/configs/p3450-0000.h
> new file mode 100644
> index 0000000..7f05beb
> --- /dev/null
> +++ b/include/configs/p3450-0000.h
> @@ -0,0 +1,46 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * (C) Copyright 2018-2019 NVIDIA Corporation.
> + */
> +
> +#ifndef _P3450_0000_H
> +#define _P3450_0000_H
> +
> +#include <linux/sizes.h>
> +
> +#include "tegra210-common.h"
> +
> +/* High-level configuration options */
> +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA P3450-0000"
> +
> +/* Board-specific serial config */
> +#define CONFIG_TEGRA_ENABLE_UARTA
> +
> +/* Only MMC/PXE/DHCP for now, add USB back in later when supported */
> +#define BOOT_TARGET_DEVICES(func) \
> + func(MMC, mmc, 1) \
> + func(MMC, mmc, 0) \
> + func(PXE, pxe, na) \
> + func(DHCP, dhcp, na)
> +
> +/* Environment at end of QSPI, in the VER partition */
> +#define CONFIG_ENV_SPI_MAX_HZ 48000000
> +#define CONFIG_ENV_SPI_MODE SPI_MODE_0
> +#define CONFIG_SPI_FLASH_SIZE (4 << 20)
> +
> +#define CONFIG_PREBOOT
> +
> +#define BOARD_EXTRA_ENV_SETTINGS \
> + "preboot=if test -e mmc 1:1 /u-boot-preboot.scr; then " \
> + "load mmc 1:1 ${scriptaddr} /u-boot-preboot.scr; " \
> + "source ${scriptaddr}; " \
> + "fi\0"
> +
> +/* General networking support */
> +#include "tegra-common-usb-gadget.h"
> +#include "tegra-common-post.h"
> +
> +/* Crystal is 38.4MHz. clk_m runs at half that rate */
> +#define COUNTER_FREQUENCY 19200000
> +
> +#endif /* _P3450_0000_H */
> --
> 1.8.2.1.610.g562af5b
>
>
> -----------------------------------------------------------------------------------
> This email message is for the sole use of the intended recipient(s) and may contain
> confidential information. Any unauthorized review, use, disclosure or distribution
> is prohibited. If you are not the intended recipient, please contact the sender by
> reply email and destroy all copies of the original message.
> -----------------------------------------------------------------------------------
More information about the U-Boot
mailing list