[PATCH] serial: ns16550: Fix ordering of getting base address

[Andy Shevchenko]

On Fri, Apr 03, 2020 at 02:58:08AM -0700, Bin Meng wrote:
> Currently the driver gets ns16550 base address in the driver
> probe() routine, which may potentially break any ns16550 wrapper
> driver that does additional initialization before calling
> ns16550_serial_probe().
> 
> Things are complicated that we need consider ns16550 devices on
> both simple-bus and PCI bus. To fix the issue we move the base
> address assignment for simple-bus ns16550 device back to the
> ofdata_to_platdata(), and assign base address for PCI ns16550
> device in ns16550_serial_probe().
> 
> This is still not perfect. Ideally if any PCI bus based ns16550
> wrapper driver tries to access plat->base before calling probe(),
> it is subject to break.

Thank you.
I have tested it and it fixes my case.

Tested-by: Andy Shevchenko <andriy.shevchenko at linux.intel.com>


> Fixes: 720f9e1fdb0c9 ("serial: ns16550: Move PCI access from
> ofdata_to_platdata() to probe()")

I believe this should be one line.

> Reported-by: Andy Shevchenko <andriy.shevchenko at linux.intel.com>
> Signed-off-by: Bin Meng <bmeng.cn at gmail.com>
> 
> ---
> 
>  drivers/serial/ns16550.c | 51 +++++++++++++++++++++++-------------------------
>  1 file changed, 24 insertions(+), 27 deletions(-)
> 
> diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
> index c1b303f..5e3cd1c 100644
> --- a/drivers/serial/ns16550.c
> +++ b/drivers/serial/ns16550.c
> @@ -479,39 +479,24 @@ static int ns16550_serial_getinfo(struct udevice *dev,
>  	return 0;
>  }
>  
> -#if CONFIG_IS_ENABLED(OF_CONTROL) && !CONFIG_IS_ENABLED(OF_PLATDATA)
> -static int ns1655_serial_set_base_addr(struct udevice *dev)
> -{
> -	fdt_addr_t addr;
> -	struct ns16550_platdata *plat;
> -
> -	plat = dev_get_platdata(dev);
> -
> -	addr = dev_read_addr_pci(dev);
> -	if (addr == FDT_ADDR_T_NONE)
> -		return -EINVAL;
> -
> -#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
> -	plat->base = addr;
> -#else
> -	plat->base = (unsigned long)map_physmem(addr, 0, MAP_NOCACHE);
> -#endif
> -
> -	return 0;
> -}
> -#endif
> -
>  int ns16550_serial_probe(struct udevice *dev)
>  {
> +	struct ns16550_platdata *plat = dev->platdata;
>  	struct NS16550 *const com_port = dev_get_priv(dev);
>  	struct reset_ctl_bulk reset_bulk;
> +	fdt_addr_t addr;
>  	int ret;
>  
> -#if CONFIG_IS_ENABLED(OF_CONTROL) && !CONFIG_IS_ENABLED(OF_PLATDATA)
> -	ret = ns1655_serial_set_base_addr(dev);
> -	if (ret)
> -		return ret;
> -#endif
> +	/*
> +	 * If we are on PCI bus, either directly attached to a PCI root port,
> +	 * or via a PCI bridge, assign platdata->base before probing hardware.
> +	 */
> +	if (device_is_on_pci_bus(dev)) {
> +		addr = devfdt_get_addr_pci(dev);
> +		if (addr == FDT_ADDR_T_NONE)
> +			return -EINVAL;
> +		plat->base = addr;
> +	}
>  
>  	ret = reset_get_bulk(dev, &reset_bulk);
>  	if (!ret)
> @@ -535,9 +520,21 @@ int ns16550_serial_ofdata_to_platdata(struct udevice *dev)
>  {
>  	struct ns16550_platdata *plat = dev->platdata;
>  	const u32 port_type = dev_get_driver_data(dev);
> +	fdt_addr_t addr;
>  	struct clk clk;
>  	int err;
>  
> +	addr = dev_read_addr(dev);
> +	if (addr != FDT_ADDR_T_NONE) {
> +#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
> +		plat->base = addr;
> +#else
> +		plat->base = (unsigned long)map_physmem(addr, 0, MAP_NOCACHE);
> +#endif
> +	} else if (!device_is_on_pci_bus(dev)) {
> +		return -EINVAL;
> +	}
> +
>  	plat->reg_offset = dev_read_u32_default(dev, "reg-offset", 0);
>  	plat->reg_shift = dev_read_u32_default(dev, "reg-shift", 0);
>  	plat->reg_width = dev_read_u32_default(dev, "reg-io-width", 1);
> -- 
> 2.7.4
> 

-- 
With Best Regards,
Andy Shevchenko