[PATCH 4/4] configs: ls1028aqds: add lpuart config

[Priyanka Jain (OSS)]

>-----Original Message-----
>From: U-Boot <u-boot-bounces at lists.denx.de> On Behalf Of
>andy.tang at nxp.com
>Sent: Thursday, March 19, 2020 2:18 PM
>To: Priyanka Jain <priyanka.jain at nxp.com>
>Cc: Sudhanshu Gupta <sudhanshu.gupta at nxp.com>; u-boot at lists.denx.de;
>Andy Tang <andy.tang at nxp.com>; Vabhav Sharma
><vabhav.sharma at nxp.com>
>Subject: [PATCH 4/4] configs: ls1028aqds: add lpuart config
>
>From: Yuantian Tang <andy.tang at nxp.com>
>
>Add lpuart config to enable lpuart feature.
>
>Signed-off-by: Vabhav Sharma <vabhav.sharma at nxp.com>
>Signed-off-by: Yuantian Tang <andy.tang at nxp.com>.
>---
> configs/ls1028aqds_tfa_lpuart_defconfig | 88 +++++++++++++++++++++++++
> 1 file changed, 88 insertions(+)
> create mode 100644 configs/ls1028aqds_tfa_lpuart_defconfig
>
>diff --git a/configs/ls1028aqds_tfa_lpuart_defconfig
>b/configs/ls1028aqds_tfa_lpuart_defconfig
>new file mode 100644
>index 0000000000..417f29217a
>--- /dev/null
>+++ b/configs/ls1028aqds_tfa_lpuart_defconfig
>@@ -0,0 +1,88 @@
>+CONFIG_ARM=y
>+CONFIG_TARGET_LS1028AQDS=y
>+CONFIG_TFABOOT=y
>+CONFIG_SYS_MALLOC_F_LEN=0x6000
>+CONFIG_ENV_SIZE=0x2000
>+CONFIG_ENV_SECT_SIZE=0x40000
>+CONFIG_ENV_OFFSET=0x500000
>+CONFIG_DM_GPIO=y
>+CONFIG_FSPI_AHB_EN_4BYTE=y
>+CONFIG_NR_DRAM_BANKS=2
>+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
>+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
>+CONFIG_AHCI=y
>+CONFIG_DISTRO_DEFAULTS=y
>+CONFIG_FIT_VERBOSE=y
>+CONFIG_OF_BOARD_SETUP=y
>+CONFIG_OF_STDOUT_VIA_ALIAS=y
>+CONFIG_BOOTDELAY=10
>+CONFIG_USE_BOOTARGS=y
>+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0
>earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000
>default_hugepagesz=2m hugepagesz=2m hugepages=256 video=1920x1080-
>32 at 60 cma=256M"
>+CONFIG_SYS_EXTRA_OPTIONS="LPUART"
>+CONFIG_MISC_INIT_R=y
>+CONFIG_CMD_GREPENV=y
>+CONFIG_CMD_DM=y
>+CONFIG_CMD_GPT=y
>+CONFIG_CMD_I2C=y
>+CONFIG_CMD_MMC=y
>+CONFIG_CMD_PCI=y
>+CONFIG_CMD_USB=y
>+CONFIG_CMD_WDT=y
>+# CONFIG_CMD_SETEXPR is not set
>+CONFIG_CMD_CACHE=y
>+CONFIG_OF_CONTROL=y
>+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-qds-lpuart"
>+CONFIG_ENV_IS_IN_MMC=y
>+CONFIG_ENV_IS_IN_SPI_FLASH=y
>+CONFIG_ENV_ADDR=0x20500000
>+CONFIG_NET_RANDOM_ETHADDR=y
>+CONFIG_NETCONSOLE=y
>+CONFIG_DM=y
>+CONFIG_SCSI_AHCI=y
>+CONFIG_SATA_CEVA=y
>+CONFIG_FSL_CAAM=y
>+CONFIG_DM_I2C=y
>+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
>+CONFIG_I2C_DEFAULT_BUS_NUMBER=0
>+CONFIG_I2C_MUX=y
>+CONFIG_I2C_MUX_PCA954x=y
>+CONFIG_DM_MMC=y
>+CONFIG_FSL_ESDHC=y
>+CONFIG_MTD=y
>+CONFIG_DM_SPI_FLASH=y
>+CONFIG_SPI_FLASH_SPANSION=y
>+CONFIG_SPI_FLASH_STMICRO=y
>+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set CONFIG_PHYLIB=y
>+CONFIG_PHY_AQUANTIA=y CONFIG_PHY_ATHEROS=y
>CONFIG_PHY_VITESSE=y
>+CONFIG_DM_ETH=y CONFIG_DM_MDIO=y CONFIG_DM_MDIO_MUX=y
>CONFIG_E1000=y
>+CONFIG_FSL_ENETC=y CONFIG_MDIO_MUX_I2CREG=y CONFIG_PCI=y
>+CONFIG_DM_PCI=y CONFIG_DM_PCI_COMPAT=y
>CONFIG_PCIE_ECAM_GENERIC=y
>+CONFIG_PCIE_LAYERSCAPE=y CONFIG_DM_RTC=y CONFIG_RTC_PCF2127=y
>+CONFIG_SCSI=y CONFIG_DM_SCSI=y CONFIG_DM_SERIAL=y
>CONFIG_FSL_LPUART=y
>+CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_FSL_DSPI=y CONFIG_NXP_FSPI=y
>+CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y
>+CONFIG_USB_XHCI_DWC3=y CONFIG_WDT=y CONFIG_WDT_SP805=y
>+CONFIG_OF_LIBFDT_OVERLAY=y CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
>--
>2.17.1

Please fix buildman warning
+(ls1028aqds_tfa_lpuart) *** Can't find default configuration "arch/../configs/ls1028aqds_tfa_lpuart_defconfig"!

Add Maintainer corresponding to this defconfig in board/freescale/ls1028a/MAINTAINERS

Thanks
Priyanka