[PATCH v2] configs: ls1028aqds: add lpuart config

[Yuantian Tang]

Add lpuart config to enable lpuart feature.

Signed-off-by: Vabhav Sharma <vabhav.sharma at nxp.com>
Signed-off-by: Yuantian Tang <andy.tang at nxp.com>.
---
v2:
	- fix buildman compiling warnings
 board/freescale/ls1028a/MAINTAINERS     |  1 +
 configs/ls1028aqds_tfa_lpuart_defconfig | 88 +++++++++++++++++++++++++++++++++
 2 files changed, 89 insertions(+)
 create mode 100644 configs/ls1028aqds_tfa_lpuart_defconfig

diff --git a/board/freescale/ls1028a/MAINTAINERS b/board/freescale/ls1028a/MAINTAINERS
index 2c28825..5b7a8db 100644
--- a/board/freescale/ls1028a/MAINTAINERS
+++ b/board/freescale/ls1028a/MAINTAINERS
@@ -8,6 +8,7 @@ F:	board/freescale/ls1028a/
 F:	include/configs/ls1028a_common.h
 F:	include/configs/ls1028aqds.h
 F:	configs/ls1028aqds_tfa_defconfig
+F:	configs/ls1028aqds_tfa_lpuart_defconfig
 
 LS1028ARDB BOARD
 M:	Sudhanshu Gupta <sudhanshu.gupta at nxp.com>
diff --git a/configs/ls1028aqds_tfa_lpuart_defconfig b/configs/ls1028aqds_tfa_lpuart_defconfig
new file mode 100644
index 0000000..417f292
--- /dev/null
+++ b/configs/ls1028aqds_tfa_lpuart_defconfig
@@ -0,0 +1,88 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1028AQDS=y
+CONFIG_TFABOOT=y
+CONFIG_SYS_MALLOC_F_LEN=0x6000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_SECT_SIZE=0x40000
+CONFIG_ENV_OFFSET=0x500000
+CONFIG_DM_GPIO=y
+CONFIG_FSPI_AHB_EN_4BYTE=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256 video=1920x1080-32 at 60 cma=256M"
+CONFIG_SYS_EXTRA_OPTIONS="LPUART"
+CONFIG_MISC_INIT_R=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_CACHE=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-qds-lpuart"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_ADDR=0x20500000
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_FSL_CAAM=y
+CONFIG_DM_I2C=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_I2C_DEFAULT_BUS_NUMBER=0
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_PHY_AQUANTIA=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_PHY_VITESSE=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_MDIO_MUX=y
+CONFIG_E1000=y
+CONFIG_FSL_ENETC=y
+CONFIG_MDIO_MUX_I2CREG=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_ECAM_GENERIC=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_PCF2127=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_NXP_FSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_WDT=y
+CONFIG_WDT_SP805=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
-- 
2.9.5