[PATCH v3 0/7] Arm Juno board OF_CONTROL upgrade

[Andre Przywara]

Hi,

another small update, fixing the Raspberry Pi breakage from the previous
version. Only patch 2/7 has changed.
I added Linus' Reviewed-by: to patch 7/7 and dropped Simon's R-b: to
patch 2/7, because of the changes.

Cheers,
Andre

------------
The Juno port in U-Boot didn't see much love lately, so it has fallen
a bit behind. We already get a build warning for using an old network
driver, but there is more:
- The port is using hardcoded information, even though we have quite
  decent DTs available to find things at runtime.
- There is no support for USB or PCI, which pretty much limits the board
  to load a kernel from flash (yuck!) or TFTP (at least!).
- Probably because of this, newer features like UEFI support don't work
  properly.
- There are minor things like less-than-ideal default load addresses and
  missing reset support.

This series is the first part of fixing this. The main part is to switch
the board port to use OF_CONTROL, so U-Boot will use a DT to configure
itself at runtime. This requires some update to the PL011 driver first
(patch 2/7), and allows us to simply enable USB in the defconfig (patch
6/7). USB requires two "usb reset" calls after the initial "usb start" to
recognise any devices, not sure why this is.
But eventually I am able to load grub from a USB hard drive and do a full
featured Ubuntu UEFI boot from there (with a distro kernel).

Patches 1, 3, and 7 are mere fixes, patch 4/7 does the actual OF_CONTROL
conversion.

I also have some proper DM_PCI compliant driver in an advanced state,
which allows to load from a SATA hard disk. Unfortunately there is no
sky2 network driver in U-Boot, so the Gigabit Ethernet chip connected
to PCI will not work easily.
I will post this once this is cleaned up and tested.

Converting the smc network driver to DM_ETH is on my list as well, but
the code is shared with some U-Boot *application* code, also used by
some PowerPC boards, so that's not really a low hanging fruit.
But it would remove the deprecation warning.

Cheers,
Andre

Changelog v2 ... v3:
- cope with platforms not defining CONFIG_PL011_CLOCK

Changelog v1 ... v2:
- drop fdt_high and initrd_high variables
- rename initrd_addr to ramdisk_addr_r

P.S. In case you want to test this without flashing it, you can
chainload U-Boot from an existing U-Boot installation:
$ mkimage -A arm64 -O u-boot -T standalone -C none -a 0xe0000000 -e 0xe0000000
  -d u-boot.bin -n U-Boot /srv/tftp/u-boot-juno.img
VExpress64# tftpboot 0xe0000000 u-boot-juno.img
VExpress64# bootm

Andre Przywara (7):
  arm: juno: Fix Juno address variables
  uart: pl011: Add proper DM clock support
  arm: juno: Fix UART clock rate
  arm: juno: Enable OF_CONTROL
  arm: juno: Use PSCI based reset
  arm: juno: enable USB
  arm: vexpress64: Remove unneeded CONFIG_ check

 arch/arm/Kconfig                       | 11 +++++
 board/armltd/vexpress64/Kconfig        |  7 +++
 board/armltd/vexpress64/vexpress64.c   | 61 ++++++++++++++++++++++++--
 configs/vexpress_aemv8a_juno_defconfig |  9 ++--
 drivers/serial/serial_pl01x.c          | 47 +++++++++++++-------
 include/configs/vexpress_aemv8a.h      | 41 ++++++++---------
 6 files changed, 132 insertions(+), 44 deletions(-)

-- 
2.17.5