[PATCH 3/3] arm64: dts: imx8mm-beacon: Re-sync dts file with Linux 5.10-rc6

Adam Ford aford173 at gmail.com
Sat Dec 5 00:27:47 CET 2020


There have been some updates to the device trees, so re-sync.

Signed-off-by: Adam Ford <aford173 at gmail.com>

diff --git a/arch/arm/dts/imx8mm-beacon-baseboard.dtsi b/arch/arm/dts/imx8mm-beacon-baseboard.dtsi
index baa5f997d0..d6b9dedd16 100644
--- a/arch/arm/dts/imx8mm-beacon-baseboard.dtsi
+++ b/arch/arm/dts/imx8mm-beacon-baseboard.dtsi
@@ -10,19 +10,19 @@
 		led0 {
 			label = "gen_led0";
 			gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>;
-			default-state = "none";
+			default-state = "off";
 		};
 
 		led1 {
 			label = "gen_led1";
 			gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
-			default-state = "none";
+			default-state = "off";
 		};
 
 		led2 {
 			label = "gen_led2";
 			gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
-			default-state = "none";
+			default-state = "off";
 		};
 
 		led3 {
@@ -70,7 +70,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 0>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom at 0 {
@@ -210,7 +210,7 @@
 		>;
 	};
 
-	pinctrl_pcal6414: pcal6414-gpio {
+	pinctrl_pcal6414: pcal6414-gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19
 		>;
@@ -240,7 +240,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B	0x41
 			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -259,7 +259,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x194
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d4
@@ -271,7 +271,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x196
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d6
diff --git a/arch/arm/dts/imx8mm-beacon-som.dtsi b/arch/arm/dts/imx8mm-beacon-som.dtsi
index 801bd02eae..b88c3c99b0 100644
--- a/arch/arm/dts/imx8mm-beacon-som.dtsi
+++ b/arch/arm/dts/imx8mm-beacon-som.dtsi
@@ -24,6 +24,26 @@
 	cpu-supply = <&buck2_reg>;
 };
 
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
@@ -52,9 +72,10 @@
 	pmic at 4b {
 		compatible = "rohm,bd71847";
 		reg = <0x4b>;
+		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
@@ -116,7 +137,7 @@
 
 			ldo1_reg: LDO1 {
 				regulator-name = "ldo1";
-				regulator-min-microvolt = <3000000>;
+				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
 				regulator-always-on;
@@ -124,7 +145,7 @@
 
 			ldo2_reg: LDO2 {
 				regulator-name = "ldo2";
-				regulator-min-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
 				regulator-always-on;
@@ -164,7 +185,7 @@
 	status = "okay";
 
 	eeprom at 50 {
-		compatible = "microchip, at24c64d", "atmel,24c64";
+		compatible = "microchip,24c64", "atmel,24c64";
 		pagesize = <32>;
 		read-only;	/* Manufacturing EEPROM programmed at factory */
 		reg = <0x50>;
@@ -190,6 +211,7 @@
 		host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 		device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
 		clocks = <&osc_32k>;
+		max-speed = <4000000>;
 		clock-names = "extclk";
 	};
 };
@@ -270,9 +292,9 @@
 			>;
 		};
 
-		pinctrl_pmic: pmicirq {
+		pinctrl_pmic: pmicirqgrp {
 			fsl,pins = <
-				MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41
+				MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x141
 			>;
 		};
 
@@ -289,7 +311,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_gpio: usdhc1grpgpio {
+		pinctrl_usdhc1_gpio: usdhc1gpiogrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10	0x41
 			>;
@@ -306,7 +328,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194
 				MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4
@@ -317,7 +339,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196
 				MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6
@@ -344,7 +366,7 @@
 			>;
 		};
 
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
 				MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
@@ -360,7 +382,7 @@
 			>;
 		};
 
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
 				MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
-- 
2.25.1



More information about the U-Boot mailing list