[PATCH v2] arm: mvebu: a38x: Configurable USB2 high-speed impedance threshold

[Stefan Roese]

On 08.11.20 22:14, Joshua Scott wrote:
> Hardware testing of a board using the Armada 385 has shown that an
> impedance threshold setting of 0x7 performs better in an eye-diagram
> test than with Marvell's recommended value 0x6.
> 
> As other boards may still perform better with Marvell's reccomended value,
> a configuration option is added with a default value of 0x6.
> 
> Signed-off-by: Joshua Scott <joshua.scott at alliedtelesis.co.nz>
> Reviewed-by: Stefan Roese <sr at denx.de>

Applied to u-boot-marvell/master

Thanks,
Stefan

> ---
> Changes for v2:
>      - Added "range" to Kconfig to prevent invalid values from being
>        selected.
> 
>   arch/arm/mach-mvebu/Kconfig                           | 6 ++++++
>   arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c | 6 +++---
>   2 files changed, 9 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index 0d8e0922a2..72aee8b3e5 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -30,6 +30,12 @@ config ARMADA_38X
>   	select ARMADA_32BIT
>   	select HAVE_MVEBU_EFUSE
>   
> +config ARMADA_38X_HS_IMPEDANCE_THRESH
> +	hex  "Armada 38x USB 2.0 High-Speed Impedance Threshold (0x0 - 0x7)"
> +	depends on ARMADA_38X
> +	default 0x6
> +	range 0x0 0x7
> +
>   config ARMADA_XP
>   	bool
>   	select ARMADA_32BIT
> diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
> index 2454730e6d..ae2a361104 100644
> --- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
> +++ b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
> @@ -677,9 +677,9 @@ struct op_params usb2_power_up_params[] = {
>   	{0xc200c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0},
>   	{0xc400c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0},
>   	/* Change the High speed impedance threshold */
> -	{0xc0008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0},
> -	{0xc2008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0},
> -	{0xc4008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0},
> +	{0xc0008, 0x0 /*NA*/, 0x700, {CONFIG_ARMADA_38X_HS_IMPEDANCE_THRESH << 8}, 0, 0},
> +	{0xc2008, 0x0 /*NA*/, 0x700, {CONFIG_ARMADA_38X_HS_IMPEDANCE_THRESH << 8}, 0, 0},
> +	{0xc4008, 0x0 /*NA*/, 0x700, {CONFIG_ARMADA_38X_HS_IMPEDANCE_THRESH << 8}, 0, 0},
>   	/* Change the squelch level of the receiver to meet the receiver electrical measurements (squelch and receiver sensitivity tests) */
>   	{0xc0014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0},
>   	{0xc2014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0},
> 


Viele Grüße,
Stefan

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de