[PATCH] mmc: meson-gx: change clock phase value on AGX SoCs

[Jaehoon Chung]

Hi,

On 12/8/20 2:15 AM, Stefan Agner wrote:
> Amlogic AGX SoCs seem to have issue communicating with some eMMC
> devices (in particular with a Micron 128GB eMMC 5.1). The device
> is detected with 1-bit bus width, and at higher temperature loading
> pretty much anything from the storage fails: (e.g. fs_devread read error
> - block).
> 
> When phase is set to 270° it is detected with 8-bit bus width and is
> working fine accross all temperatures.
> 
> Signed-off-by: Stefan Agner <stefan at agner.ch>
> ---
> Hi Neil,
> 
> I debugged this issue today on an ODROID N2+ not booting reliably. I am
> not sure if we can safely switch to 270° for all SoCs with
> amlogic,meson-axg-mmc, but I guess we have to try and see what happens?
> I will do a bit broader testing in the comming days here.

Some SoCs don't work fine with 180'. So I have changed 270' phase and Neil had applied SoC compatible.
I guess that it's relevant to controlling clock. But In u-boot, meson_gx_mmc doesn't follow Linux kernel fully.
I will refactor meson_gxm_mmc file after finished my other work.

> 
> Btw, I do see that 180° is also set in Linux. Do you have a patch to
> address this in Linux?

I didn't check Linux kernel yet in more detail. Also, i will investigate to check a meson mmc driver after finished my other job.

Best Regards,
Jaehoon Chung

> 
> --
> Stefan
> 
> 
>  arch/arm/include/asm/arch-meson/sd_emmc.h | 1 +
>  drivers/mmc/meson_gx_mmc.c                | 9 +++++----
>  2 files changed, 6 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm/include/asm/arch-meson/sd_emmc.h b/arch/arm/include/asm/arch-meson/sd_emmc.h
> index cb16f75fc6..db5e058098 100644
> --- a/arch/arm/include/asm/arch-meson/sd_emmc.h
> +++ b/arch/arm/include/asm/arch-meson/sd_emmc.h
> @@ -14,6 +14,7 @@
>  
>  enum meson_gx_mmc_compatible {
>  	MMC_COMPATIBLE_GX,
> +	MMC_COMPATIBLE_AGX,
>  	MMC_COMPATIBLE_SM1,
>  };
>  
> diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
> index 5facbfdd9a..2c27113c10 100644
> --- a/drivers/mmc/meson_gx_mmc.c
> +++ b/drivers/mmc/meson_gx_mmc.c
> @@ -64,14 +64,15 @@ static void meson_mmc_config_clock(struct mmc *mmc)
>  
>  	/*
>  	 * SM1 SoCs doesn't work fine over 50MHz with CLK_CO_PHASE_180
> +	 * AGX SoCs don't work reliable with some eMMCs with CLK_CO_PHASE_180
>  	 * If CLK_CO_PHASE_270 is used, it's more stable than other.
>  	 * Other SoCs use CLK_CO_PHASE_180 by default.
>  	 * It needs to find what is a proper value about each SoCs.
>  	 */
> -	if (meson_gx_mmc_is_compatible(mmc->dev, MMC_COMPATIBLE_SM1))
> -		meson_mmc_clk |= CLK_CO_PHASE_270;
> -	else
> +	if (meson_gx_mmc_is_compatible(mmc->dev, MMC_COMPATIBLE_GX))
>  		meson_mmc_clk |= CLK_CO_PHASE_180;
> +	else
> +		meson_mmc_clk |= CLK_CO_PHASE_270;
>  
>  	/* 180 phase tx clock */
>  	meson_mmc_clk |= CLK_TX_PHASE_000;
> @@ -327,7 +328,7 @@ int meson_mmc_bind(struct udevice *dev)
>  
>  static const struct udevice_id meson_mmc_match[] = {
>  	{ .compatible = "amlogic,meson-gx-mmc", .data = MMC_COMPATIBLE_GX },
> -	{ .compatible = "amlogic,meson-axg-mmc", .data = MMC_COMPATIBLE_GX },
> +	{ .compatible = "amlogic,meson-axg-mmc", .data = MMC_COMPATIBLE_AGX },
>  	{ .compatible = "amlogic,meson-sm1-mmc", .data = MMC_COMPATIBLE_SM1 },
>  	{ /* sentinel */ }
>  };
>