[PATCH v5 7/7] doc: board: Add Microchip MPFS Icicle Kit doc
Bin Meng
bmeng.cn at gmail.com
Thu Dec 10 07:37:41 CET 2020
Hi Padmarao,
On Thu, Dec 3, 2020 at 4:44 AM Padmarao Begari
<padmarao.begari at microchip.com> wrote:
>
> This doc describes the procedure to build, flash and
> boot Linux using U-boot on Microchip MPFS Icicle Kit.
>
> Signed-off-by: Padmarao Begari <padmarao.begari at microchip.com>
> Reviewed-by: Anup Patel <anup.patel at wdc.com>
> ---
> doc/board/index.rst | 1 +
> doc/board/microchip/index.rst | 9 +
> doc/board/microchip/mpfs_icicle.rst | 830 ++++++++++++++++++++++++++++
> 3 files changed, 840 insertions(+)
> create mode 100644 doc/board/microchip/index.rst
> create mode 100644 doc/board/microchip/mpfs_icicle.rst
>
> diff --git a/doc/board/index.rst b/doc/board/index.rst
> index 4b6a996eb1..e329e2744c 100644
> --- a/doc/board/index.rst
> +++ b/doc/board/index.rst
> @@ -15,6 +15,7 @@ Board-specific doc
> freescale/index
> google/index
> intel/index
> + microchip/index
nits: this should be inserted after kontron/index
> kontron/index
> renesas/index
> rockchip/index
> diff --git a/doc/board/microchip/index.rst b/doc/board/microchip/index.rst
> new file mode 100644
> index 0000000000..b09e6788af
> --- /dev/null
> +++ b/doc/board/microchip/index.rst
> @@ -0,0 +1,9 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +Microchip
> +======
nits: please make sure the delimiter has the same width as the sub-titles
please fix similar issue globally in this file
> +
> +.. toctree::
> + :maxdepth: 2
> +
> + mpfs_icicle
> diff --git a/doc/board/microchip/mpfs_icicle.rst b/doc/board/microchip/mpfs_icicle.rst
> new file mode 100644
> index 0000000000..d37b9bcb92
> --- /dev/null
> +++ b/doc/board/microchip/mpfs_icicle.rst
> @@ -0,0 +1,830 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +Microchip PolarFire SoC Icicle Kit
> +==================================
> +
> +RISC-V PolarFire SoC
> +---------------------
> +The PolarFire SoC is the 4+1 64-bit RISC-V SoC from Microchip.
> +
> +The Icicle Kit development platform is based on PolarFire SoC and capable
> +of running Linux.
> +
> +Mainline support
> +----------------
> +The support for following drivers are already enabled:
> +
> +1. NS16550 UART Driver.
> +2. Microchip Clock Driver.
> +3. Cadence MACB ethernet driver for networking support.
> +4. Cadence MMC Driver for eMMC/SD support.
> +
> +Booting from eMMC using HSS
> +---------------------------
> +
> +Building U-Boot
> +---------------
> +
> +1. Add the RISC-V toolchain to your PATH.
> +2. Setup ARCH & cross compilation environment variable:
> +
> +.. code-block:: none
> +
> + export CROSS_COMPILE=<riscv64 toolchain prefix>
> +
> +3. make microchip_mpfs_icicle_defconfig
> +4. make
> +
> +Flashing
> +--------
> +
> +The current U-Boot port is supported in S-mode only and loaded from DRAM.
> +
> +A prior stage M-mode firmware/bootloader (e.g HSS with OpenSBI) is required to
> +boot the u-boot.bin in S-mode.
> +
> +Currently, the u-boot.bin is used as a payload of the HSS firmware(Microchip
nits: needs a space before ( and after )
Please fix this globally in this file.
> +boot-flow) and OpenSBI generic platform fw_payload.bin (with u-boot.bin embedded)
> +as HSS payload(Custom boot-flow)
> +
> +Microchip boot-flow
> +-------------------
> +HSS with OpenSBI(M-Mode) -> U-Boot(S-Mode) -> Linux(S-Mode)
> +
> +Build the HSS((Hart Software Services) - Microchip boot-flow
redundant (
> +------------------------------------------------------------
> +(Note: HSS git repo is at
> +https://github.com/polarfire-soc/hart-software-services)
> +
> +1. Configure
> +
> +.. code-block:: none
> +
> + make BOARD=icicle-kit-es config
> +
> +Alternatively, copy the default config for Microchip boot-flow.
> +
> +.. code-block:: none
> +
> + cp boards/icicle-kit-es/def_config .config
> +
> +2. make BOARD=icicle-kit-es
> +3. In the Default subdirectory, the standard build will create hss.elf and
> + various binary formats (hss.hex and hss.bin).
> +
> +The FPGA design will use the hss.hex or hss.bin.
> +
> +FPGA design with HSS programming file
> +-------------------------------------
> +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards
> +/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md
Having the URL in 2 lines breaks the link, I think.
> +
> +The HSS firmware runs from the PolarFire SoC eNVM on reset.
> +
> +Creating the HSS payload - Microchip boot-flow
> +----------------------------------------------
> +1. You will be creating a payload from `u-boot-dtb.bin`.
> + Copy this file to the HSS/tools/hss-payload-generator/test directory.
> +2. Go to hss-payload-generator source directory.
> +
> +.. code-block:: none
> +
> + cd hart-software-services/tools/hss-payload-generator
> +
> +3. Edit test/uboot.yaml file for hart entry points and correct name of the binary file.
> +
> + hart-entry-points: {u54_1: '0x80200000', u54_2: '0x80200000',
> + u54_3: '0x80200000', u54_4: '0x80200000'}
> +
> + payloads:
> + test/u-boot-dtb.bin: {exec-addr: '0x80200000', owner-hart: u54_1,
> + secondary-hart: u54_2, secondary-hart: u54_3, secondary-hart: u54_4,
> + priv-mode: prv_s}
> +
> +4. Generate payload
> +
> +.. code-block:: none
> +
> + ./hss-payload-generator -c test/uboot.yaml payload.bin
> +
> +Once the payload binary is generated, it should be copied to the eMMC.
> +
> +Please refer to HSS documenation to build the HSS firmware for payload.
> +(Note: HSS git repo is at
> +https://github.com/polarfire-soc/hart-software-services/blob/master
> +/tools/hss-payload-generator/README.md)
> +
> +Custom boot-flow
> +----------------
> +HSS without OpenSBI(M-Mode) -> OpenSBI(M-Mode) -> U-Boot(S-Mode) -> Linux(S-Mode)
> +
> +Build OpenSBI
> +-------------
> +
> +1. Get the OpenSBI source
> +
> +.. code-block:: none
> +
> + git clone https://github.com/riscv/opensbi.git
> + cd opensbi
> +
> +2. Build
> +
> +.. code-block:: none
> +
> + make PLATFORM=generic FW_PAYLOAD_PATH=<u-boot-directory>/u-boot.bin
> + FW_FDT_PATH=<u-boot-directory>/arch/riscv/dts/microchip-mpfs-icicle-kit-.dtb
> +
> +3. Output "fw_payload.bin" file available at
> + "<opensbi-directory>/build/platform/generic/firmware/fw_payload.bin"
> +
> +Build the HSS((Hart Software Services)- Custom boot-flow
> +--------------------------------------------------------
> +(Note: HSS git repo is at
> +https://github.com/polarfire-soc/hart-software-services)
> +
> +1. Configure
> +
> +.. code-block:: none
> +
> + make BOARD=icicle-kit-es config
> +
> +Alternatively, copy the default custom config for Custom boot-flow.
> +
> +.. code-block:: none
> +
> + cp boards/icicle-kit-es/def_config_custom .config
> +
> +2. make BOARD=icicle-kit-es
> +3. In the Default subdirectory, the standard build will create hss.elf and
> + various binary formats (hss.hex and hss.bin).
> +
> +The FPGA design will use the hss.hex or hss.bin.
> +
> +Creating the HSS payload - Custom boot-flow
> +-------------------------------------------
> +1. You will be creating a payload from `fw_payload.bin`.
> + Copy this file to the HSS/tools/hss-payload-generator/test directory.
> +2. Go to hss-payload-generator source directory.
> +
> +.. code-block:: none
> +
> + cd hart-software-services/tools/hss-payload-generator
> +
> +3. Edit test/uboot.yaml file for hart entry points and correct name of the binary file.
> +
> + hart-entry-points: {u54_1: '0x80000000', u54_2: '0x80000000',
> + u54_3: '0x80000000', u54_4: '0x80000000'}
> +
> + payloads:
> + test/fw_payload.bin: {exec-addr: '0x80000000', owner-hart: u54_1,
> + secondary-hart: u54_2, secondary-hart: u54_3, secondary-hart: u54_4,
> + priv-mode: prv_m}
> +
> +4. Generate payload
> +
> +.. code-block:: none
> +
> + ./hss-payload-generator -c test/uboot.yaml payload.bin
> +
> +Once the payload binary is generated, it should be copied to the eMMC.
> +
> +Please refer to HSS documenation to build the HSS firmware for payload.
> +(Note: HSS git repo is at
> +https://github.com/polarfire-soc/hart-software-services/blob/master/tools
> +/hss-payload-generator/README.md
> +and also refer the HSS payload generator at
> +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master
> +/software-development/hss-payloads.md)
> +
> +eMMC
> +----
> +Program eMMC with payload binary is explained in the PolarFire SoC documentation.
> +(Note: PolarFire SoC Documentation git repo is at
> +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards
> +/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md#eMMC
> +
> +Once the payload image is copied to the eMMC, press CTRL+C in the HSS command
> +line interface, then type 'boot' and enter to boot the newly copied image.
> +
> +.. code-block:: none
> +
> + sudo dd if=<payload_binary> of=/dev/sdX bs=512
> +
> +GUID type
> +---------
> +The HSS always picks up HSS payload from a GPT partition with
> +GIUD type "21686148-6449-6E6F-744E-656564454649" or sector '0' of the eMMC if no
> +GPT partition.
> +
> +Booting
> +-------
> +you should see the U-Boot prompt on UART0.
nits: You
> +
> +Sample boot log from MPFS Icicle Kit
> +-------------------------------------------
> +
> +.. code-block:: none
> +
> + U-Boot 2021.01-rc2-00163-ge8143d680f-dirty (Dec 2 2020 - 14:21:12 +0530)
> +
> + CPU: rv64imafdc
> + Model: Microchip MPFS Icicle Kit
> + DRAM: 1 GiB
> + MMC: sdhc at 20008000: 0
> + In: serial at 20100000
> + Out: serial at 20100000
> + Err: serial at 20100000
> + Net: eth0: ethernet at 20112000
> + Hit any key to stop autoboot: 0
> +
> +Now you can configure your networking, tftp server and use tftp boot method to
> +load uImage(with initramfs).
> +
> +.. code-block:: none
> +
> + RISC-V # setenv kernel_addr_r 0x80200000
> + RISC-V # setenv fdt_addr_r 0x82200000
> +
> + RISC-V # setenv ipaddr 192.168.1.5
> + RISC-V # setenv netmask 255.255.255.0
> + RISC-V # setenv serverip 192.168.1.3
> + RISC-V # setenv gateway 192.168.1.1
> +
> + RISC-V # tftpboot ${kernel_addr_r} uImage
> + ethernet at 20112000: PHY present at 9
> + ethernet at 20112000: Starting autonegotiation...
> + ethernet at 20112000: Autonegotiation complete
> + ethernet at 20112000: link up, 1000Mbps full-duplex (lpa: 0x7800)
> + Using ethernet at 20112000 device
> + TFTP from server 192.168.1.3; our IP address is 192.168.1.5
> + Filename 'uImage'.
> + Load address: 0x80200000
> + Loading: #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + ############
> + 6.4 MiB/s
> + done
> + Bytes transferred = 14482480 (dcfc30 hex)
> +
> + RISC-V # tftpboot ${fdt_addr_r} microchip-mpfs-icicle-kit.dtb
> + ethernet at 20112000: PHY present at 9
> + ethernet at 20112000: Starting autonegotiation...
> + ethernet at 20112000: Autonegotiation complete
> + ethernet at 20112000: link up, 1000Mbps full-duplex (lpa: 0x7800)
> + Using ethernet at 20112000 device
> + TFTP from server 192.168.1.3; our IP address is 192.168.1.5
> + Filename 'microchip-mpfs-icicle-kit.dtb'.
> + Load address: 0x82200000
> + Loading: #
> + 2.5 MiB/s
> + done
> + Bytes transferred = 10282 (282a hex)
> +
> + RISC-V # bootm ${kernel_addr_r} - ${fdt_addr_r}
> + ## Booting kernel from Legacy Image at 80200000 ...
> + Image Name: Linux
> + Image Type: RISC-V Linux Kernel Image (uncompressed)
> + Data Size: 14482416 Bytes = 13.8 MiB
> + Load Address: 80200000
> + Entry Point: 80200000
> + Verifying Checksum ... OK
> + ## Flattened Device Tree blob at 82200000
> + Booting using the fdt blob at 0x82200000
> + Loading Kernel Image
> + Using Device Tree in place at 0000000082200000, end 0000000082205829
> +
> + Starting kernel ...
> +
> + [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
> + [ 0.000000] Linux version 5.6.17 (padmarao at padmarao-VirtualBox) (gcc version 7.2.0 (GCC)) #2 SMP Tue Jun 16 21:27:50 IST 2020
> + [ 0.000000] initrd not found or empty - disabling initrd
> + [ 0.000000] Zone ranges:
> + [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
> + [ 0.000000] Normal empty
> + [ 0.000000] Movable zone start for each node
> + [ 0.000000] Early memory node ranges
> + [ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
> + [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
> + [ 0.000000] software IO TLB: mapped [mem 0xbb1f5000-0xbf1f5000] (64MB)
> + [ 0.000000] elf_hwcap is 0x112d
> + [ 0.000000] percpu: Embedded 14 pages/cpu s24856 r0 d32488 u57344
> + [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
> + [ 0.000000] Kernel command line: console=ttyS0,115200n8
> + [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
> + [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
> + [ 0.000000] Sorting __ex_table...
> + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> + [ 0.000000] Memory: 950308K/1046528K available (3289K kernel code, 212K rwdata, 900K rodata, 9476K init, 250K bss, 96220K reserved, 0K cma-reserved)
> + [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
> + [ 0.000000] rcu: Hierarchical RCU implementation.
> + [ 0.000000] rcu: RCU event tracing is enabled.
> + [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
> + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
> + [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
> + [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
> + [ 0.000000] plic: mapped 186 interrupts with 4 handlers for 9 contexts.
> + [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
> + [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
> + [ 0.000015] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
> + [ 0.000311] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
> + [ 0.000349] pid_max: default: 32768 minimum: 301
> + [ 0.000846] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
> + [ 0.000964] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
> + [ 0.005630] rcu: Hierarchical SRCU implementation.
> + [ 0.006901] smp: Bringing up secondary CPUs ...
> + [ 0.012545] smp: Brought up 1 node, 4 CPUs
> + [ 0.014431] devtmpfs: initialized
> + [ 0.020526] random: get_random_bytes called from setup_net+0x36/0x192 with crng_init=0
> + [ 0.020928] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
> + [ 0.020999] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
> + [ 0.022768] NET: Registered protocol family 16
> + [ 0.035478] microchip-pfsoc-clkcfg 20002000.clkcfg: Registered PFSOC core clocks
> + [ 0.048429] SCSI subsystem initialized
> + [ 0.049694] pps_core: LinuxPPS API ver. 1 registered
> + [ 0.049719] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti at linux.it>
> + [ 0.049780] PTP clock support registered
> + [ 0.051781] clocksource: Switched to clocksource riscv_clocksource
> + [ 0.055326] NET: Registered protocol family 2
> + [ 0.056922] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
> + [ 0.057053] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
> + [ 0.057648] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
> + [ 0.058579] TCP: Hash tables configured (established 8192 bind 8192)
> + [ 0.059648] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
> + [ 0.059837] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
> + [ 0.060707] NET: Registered protocol family 1
> + [ 0.266229] workingset: timestamp_bits=62 max_order=18 bucket_order=0
> + [ 0.287107] io scheduler mq-deadline registered
> + [ 0.287140] io scheduler kyber registered
> + [ 0.429601] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> + [ 0.433979] printk: console [ttyS0] disabled
> + [ 0.434154] 20000000.serial: ttyS0 at MMIO 0x20000000 (irq = 18, base_baud = 9375000) is a 16550A
> + [ 0.928039] printk: console [ttyS0] enabled
> + [ 0.939804] libphy: Fixed MDIO Bus: probed
> + [ 0.948702] libphy: MACB_mii_bus: probed
> + [ 0.993698] macb 20112000.ethernet eth0: Cadence GEM rev 0x0107010c at 0x20112000 irq 21 (56:34:12:00:fc:00)
> + [ 1.006751] mousedev: PS/2 mouse device common for all mice
> + [ 1.013803] i2c /dev entries driver
> + [ 1.019451] sdhci: Secure Digital Host Controller Interface driver
> + [ 1.027242] sdhci: Copyright(c) Pierre Ossman
> + [ 1.032731] sdhci-pltfm: SDHCI platform and OF driver helper
> + [ 1.091826] mmc0: SDHCI controller on 20008000.sdhc [20008000.sdhc] using ADMA 64-bit
> + [ 1.102738] NET: Registered protocol family 17
> + [ 1.170326] Freeing unused kernel memory: 9476K
> + [ 1.176067] This architecture does not have kernel memory protection.
> + [ 1.184157] Run /init as init process
> + Starting logging: OK
> + Starting mdev...
> + /etc/init.d/S10mdev: line 21: can't create /proc/sys/kernel/hotplug: nonexiste[ 1.331981] mmc0: mmc_select_hs200 failed, error -74
> + nt directory
> + [ 1.355011] mmc0: new MMC card at address 0001
> + [ 1.363981] mmcblk0: mmc0:0001 DG4008 7.28 GiB
> + [ 1.372248] mmcblk0boot0: mmc0:0001 DG4008 partition 1 4.00 MiB
> + [ 1.382292] mmcblk0boot1: mmc0:0001 DG4008 partition 2 4.00 MiB
> + [ 1.390265] mmcblk0rpmb: mmc0:0001 DG4008 partition 3 4.00 MiB, chardev (251:0)
> + [ 1.425234] GPT:Primary header thinks Alt. header is not at the end of the disk.
> + [ 1.434656] GPT:2255809 != 15273599
> + [ 1.439038] GPT:Alternate GPT header not at the end of the disk.
> + [ 1.446671] GPT:2255809 != 15273599
> + [ 1.451048] GPT: Use GNU Parted to correct GPT errors.
> + [ 1.457755] mmcblk0: p1 p2 p3
> + sort: /sys/devices/platform/Fixed: No such file or directory
> + modprobe: can't change directory to '/lib/modules': No such file or directory
> + Initializing random number generator... [ 2.830198] random: dd: uninitialized urandom read (512 bytes read)
> + done.
> + Starting network...
> + [ 3.061867] macb 20112000.ethernet eth0: PHY [20112000.ethernet-ffffffff:09] driver [Vitesse VSC8662] (irq=POLL)
> + [ 3.074674] macb 20112000.ethernet eth0: configuring for phy/sgmii link mode
> + [ 3.084263] pps pps0: new PPS source ptp0
> + [ 3.089710] macb 20112000.ethernet: gem-ptp-timer ptp clock registered.
> + udhcpc (v1.24.2) started
> + Sending discover...
> + Sending discover...
> + [ 6.380169] macb 20112000.ethernet eth0: Link is Up - 1Gbps/Full - flow control tx
> + Sending discover...
> + Sending select for 192.168.1.2...
> + Lease of 192.168.1.2 obtained, lease time 86400
> + deleting routers
> + adding dns 192.168.1.1
> + Starting dropbear sshd: [ 11.385619] random: dropbear: uninitialized urandom read (32 bytes read)
> + OK
> +
> + Welcome to Buildroot
> + buildroot login: root
> + Password:
> + #
> +
> +Booting U-Boot and Linux from eMMC
> +----------------------------------
> +
> +FPGA design with HSS programming file and Linux Image
> +-----------------------------------------------------
> +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards
> +/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md
> +
> +The HSS firmware runs from the PolarFire SoC eNVM on reset.
> +
> +eMMC
> +----
> +Program eMMC with payload binary and Linux image is explained in the
> +PolarFire SoC documentation.
> +The payload binary should be copied to partition 2 of the eMMC.
> +
> +(Note: PolarFire SoC Documentation git repo is at
> +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards
> +/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md#eMMC)
> +
> +Once the Linux image and payload binary is copied to the eMMC, press CTRL+C
> +in the HSS command line interface, then type 'boot' and enter to boot the newly
> +copied payload and Linux image.
> +
> +.. code-block:: none
> +
> + zcat <linux-image>.wic.gz | sudo dd of=/dev/sdX bs=4096 iflag=fullblock oflag=direct conv=fsync status=progress
> +
> + sudo dd if=<payload_binary> of=/dev/sdX2 bs=512
> +
> +You should see the U-Boot prompt on UART0.
> +
> +GUID type
> +---------
> +The HSS always picks up the HSS payload from a GPT partition with
> +GIUD type "21686148-6449-6E6F-744E-656564454649" or sector '0' of the eMMC if no
> +GPT partition.
> +
> +Sample boot log from MPFS Icicle Kit
> +-------------------------------------------
> +
> +.. code-block:: none
> +
> + U-Boot 2021.01-rc2-00163-ge8143d680f-dirty (Dec 2 2020 - 14:21:12 +0530)
> +
> + CPU: rv64imafdc
> + Model: Microchip MPFS Icicle Kit
> + DRAM: 1 GiB
> + MMC: sdhc at 20008000: 0
> + In: serial at 20100000
> + Out: serial at 20100000
> + Err: serial at 20100000
> + Net: eth0: ethernet at 20112000
> + Hit any key to stop autoboot: 0
> +
> + RISC-V # mmc info
> + Device: sdhc at 20008000
> + Manufacturer ID: 45
> + OEM: 100
> + Name: DG400
> + Bus Speed: 52000000
> + Mode: MMC High Speed (52MHz)
> + Rd Block Len: 512
> + MMC version 5.1
> + High Capacity: Yes
> + Capacity: 7.3 GiB
> + Bus Width: 4-bit
> + Erase Group Size: 512 KiB
> + HC WP Group Size: 8 MiB
> + User Capacity: 7.3 GiB WRREL
> + Boot Capacity: 4 MiB ENH
> + RPMB Capacity: 4 MiB ENH
> +
> + RISC-V # mmc part
> + Partition Map for MMC device 0 -- Partition Type: EFI
> +
> + Part Start LBA End LBA Name
> + Attributes
> + Type GUID
> + Partition GUID
> + 1 0x00002000 0x0000b031 "boot"
> + attrs: 0x0000000000000004
> + type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
> + guid: 99ff6a94-f2e7-44dd-a7df-f3a2da106ef9
> + 2 0x0000b032 0x0000f031 "primary"
> + attrs: 0x0000000000000000
> + type: 21686148-6449-6e6f-744e-656564454649
> + guid: 12006052-e64b-4423-beb0-b956ea00f1ba
> + 3 0x00010000 0x00226b9f "root"
> + attrs: 0x0000000000000000
> + type: 0fc63daf-8483-4772-8e79-3d69d8477de4
> + guid: dd2c5619-2272-4c3c-8dc2-e21942e17ce6
> +
> + RISC-V # fatload mmc 0 ${ramdisk_addr_r} fitimage
> + RISC-V # bootm ${ramdisk_addr_r}
> + ## Loading kernel from FIT Image at 88300000 ...
> + Using 'conf at microchip_icicle-kit-es-a000-microchip.dtb' configuration
> + Trying 'kernel at 1' kernel subimage
> + Description: Linux kernel
> + Type: Kernel Image
> + Compression: gzip compressed
> + Data Start: 0x883000fc
> + Data Size: 3574555 Bytes = 3.4 MiB
> + Architecture: RISC-V
> + OS: Linux
> + Load Address: 0x80200000
> + Entry Point: 0x80200000
> + Hash algo: sha256
> + Hash value: 21f18d72cf2f0a7192220abb577ad25c77c26960052d779aa02bf55dbf0a6403
> + Verifying Hash Integrity ... sha256+ OK
> + ## Loading fdt from FIT Image at 88300000 ...
> + Using 'conf at microchip_icicle-kit-es-a000-microchip.dtb' configuration
> + Trying 'fdt at microchip_icicle-kit-es-a000-microchip.dtb' fdt subimage
> + Description: Flattened Device Tree blob
> + Type: Flat Device Tree
> + Compression: uncompressed
> + Data Start: 0x88668d44
> + Data Size: 9760 Bytes = 9.5 KiB
> + Architecture: RISC-V
> + Load Address: 0x82200000
> + Hash algo: sha256
> + Hash value: 5c3a9f30d41b6b8e53b47916e1f339b3a4d454006554d1f7e1f552ed62409f4b
> + Verifying Hash Integrity ... sha256+ OK
> + Loading fdt from 0x88668d44 to 0x82200000
> + Booting using the fdt blob at 0x82200000
> + Uncompressing Kernel Image
> + Using Device Tree in place at 0000000082200000, end 000000008220561f
> +
> + Starting kernel ...
> +
> + [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
> + [ 0.000000] Linux version 5.6.16 (oe-user at oe-host) (gcc version 9.3.0 (GCC)) #1 SMP Fri Oct 9 11:49:47 UTC 2020
> + [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '')
> + [ 0.000000] printk: bootconsole [sbi0] enabled
> + [ 0.000000] Zone ranges:
> + [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff]
> + [ 0.000000] Normal empty
> + [ 0.000000] Movable zone start for each node
> + [ 0.000000] Early memory node ranges
> + [ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff]
> + [ 0.000000] Zeroed struct page in unavailable ranges: 512 pages
> + [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff]
> + [ 0.000000] software IO TLB: mapped [mem 0xb9e00000-0xbde00000] (64MB)
> + [ 0.000000] CPU with hartid=0 is not available
> + [ 0.000000] CPU with hartid=0 is not available
> + [ 0.000000] elf_hwcap is 0x112d
> + [ 0.000000] percpu: Embedded 17 pages/cpu s29784 r8192 d31656 u69632
> + [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055
> + [ 0.000000] Kernel command line: earlycon=sbi root=/dev/mmcblk0p3 rootwait console=ttyS0,115200n8 uio_pdrv_genirq.of_id=generic-uio
> + [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
> + [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
> + [ 0.000000] Sorting __ex_table...
> + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> + [ 0.000000] Memory: 941440K/1046528K available (4118K kernel code, 280K rwdata, 1687K rodata, 169K init, 273K bss, 105088K reserved, 0K cma-reserved)
> + [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
> + [ 0.000000] rcu: Hierarchical RCU implementation.
> + [ 0.000000] rcu: RCU event tracing is enabled.
> + [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=5 to nr_cpu_ids=4.
> + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
> + [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
> + [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
> + [ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
> + [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
> + [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
> + [ 0.000015] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
> + [ 0.008679] Console: colour dummy device 80x25
> + [ 0.013112] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
> + [ 0.023368] pid_max: default: 32768 minimum: 301
> + [ 0.028314] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
> + [ 0.035766] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
> + [ 0.047099] rcu: Hierarchical SRCU implementation.
> + [ 0.052813] smp: Bringing up secondary CPUs ...
> + [ 0.061581] smp: Brought up 1 node, 4 CPUs
> + [ 0.067069] devtmpfs: initialized
> + [ 0.073621] random: get_random_u32 called from bucket_table_alloc.isra.0+0x4e/0x150 with crng_init=0
> + [ 0.074409] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
> + [ 0.093399] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
> + [ 0.101879] NET: Registered protocol family 16
> + [ 0.110336] microchip-pfsoc-clkcfg 20002000.clkcfg: Registered PFSOC core clocks
> + [ 0.132717] usbcore: registered new interface driver usbfs
> + [ 0.138225] usbcore: registered new interface driver hub
> + [ 0.143813] usbcore: registered new device driver usb
> + [ 0.148939] pps_core: LinuxPPS API ver. 1 registered
> + [ 0.153929] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti at linux.it>
> + [ 0.163071] PTP clock support registered
> + [ 0.168521] clocksource: Switched to clocksource riscv_clocksource
> + [ 0.174927] VFS: Disk quotas dquot_6.6.0
> + [ 0.179016] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> + [ 0.205536] NET: Registered protocol family 2
> + [ 0.210944] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
> + [ 0.219393] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
> + [ 0.227497] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
> + [ 0.235440] TCP: Hash tables configured (established 8192 bind 8192)
> + [ 0.242537] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
> + [ 0.249285] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
> + [ 0.256690] NET: Registered protocol family 1
> + [ 0.262585] workingset: timestamp_bits=62 max_order=18 bucket_order=0
> + [ 0.281036] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
> + [ 0.288481] io scheduler mq-deadline registered
> + [ 0.292983] io scheduler kyber registered
> + [ 0.298895] microsemi,mss-gpio 20122000.gpio: Microsemi MSS GPIO registered 32 GPIOs
> + [ 0.453723] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> + [ 0.462911] printk: console [ttyS0] disabled
> + [ 0.467216] 20100000.serial: ttyS0 at MMIO 0x20100000 (irq = 12, base_baud = 9375000) is a 16550A
> + [ 0.476201] printk: console [ttyS0] enabled
> + [ 0.476201] printk: console [ttyS0] enabled
> + [ 0.484576] printk: bootconsole [sbi0] disabled
> + [ 0.484576] printk: bootconsole [sbi0] disabled
> + [ 0.494920] 20102000.serial: ttyS1 at MMIO 0x20102000 (irq = 13, base_baud = 9375000) is a 16550A
> + [ 0.505068] 20104000.serial: ttyS2 at MMIO 0x20104000 (irq = 14, base_baud = 9375000) is a 16550A
> + [ 0.533336] loop: module loaded
> + [ 0.572284] Rounding down aligned max_sectors from 4294967295 to 4294967288
> + [ 0.580000] db_root: cannot open: /etc/target
> + [ 0.585413] libphy: Fixed MDIO Bus: probed
> + [ 0.591526] libphy: MACB_mii_bus: probed
> + [ 0.598060] macb 20112000.ethernet eth0: Cadence GEM rev 0x0107010c at 0x20112000 irq 17 (56:34:12:00:fc:00)
> + [ 0.608352] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> + [ 0.615001] ehci-platform: EHCI generic platform driver
> + [ 0.620446] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> + [ 0.626632] ohci-platform: OHCI generic platform driver
> + [ 0.632326] usbcore: registered new interface driver cdc_acm
> + [ 0.637996] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
> + [ 0.646459] i2c /dev entries driver
> + [ 0.650852] microsemi-mss-i2c 2010b000.i2c: Microsemi I2C Probe Complete
> + [ 0.658010] sdhci: Secure Digital Host Controller Interface driver
> + [ 0.664326] sdhci: Copyright(c) Pierre Ossman
> + [ 0.668754] sdhci-pltfm: SDHCI platform and OF driver helper
> + [ 0.706845] mmc0: SDHCI controller on 20008000.sdhc [20008000.sdhc] using ADMA 64-bit
> + [ 0.715052] usbcore: registered new interface driver usbhid
> + [ 0.720722] usbhid: USB HID core driver
> + [ 0.725174] pac193x 0-0010: Chip revision: 0x03
> + [ 0.733339] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 0 active
> + [ 0.740127] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 1 active
> + [ 0.746881] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 2 active
> + [ 0.753686] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 3 active
> + [ 0.760495] pac193x 0-0010: :pac193x_prep_iio_channels: Active chip channels: 25
> + [ 0.778006] NET: Registered protocol family 10
> + [ 0.784929] Segment Routing with IPv6
> + [ 0.788875] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
> + [ 0.795743] NET: Registered protocol family 17
> + [ 0.801191] hctosys: unable to open rtc device (rtc0)
> + [ 0.807774] Waiting for root device /dev/mmcblk0p3...
> + [ 0.858506] mmc0: mmc_select_hs200 failed, error -74
> + [ 0.865764] mmc0: new MMC card at address 0001
> + [ 0.872564] mmcblk0: mmc0:0001 DG4008 7.28 GiB
> + [ 0.878777] mmcblk0boot0: mmc0:0001 DG4008 partition 1 4.00 MiB
> + [ 0.886182] mmcblk0boot1: mmc0:0001 DG4008 partition 2 4.00 MiB
> + [ 0.892633] mmcblk0rpmb: mmc0:0001 DG4008 partition 3 4.00 MiB, chardev (247:0)
> + [ 0.919029] GPT:Primary header thinks Alt. header is not at the end of the disk.
> + [ 0.926448] GPT:2255841 != 15273599
> + [ 0.930019] GPT:Alternate GPT header not at the end of the disk.
> + [ 0.936029] GPT:2255841 != 15273599
> + [ 0.939583] GPT: Use GNU Parted to correct GPT errors.
> + [ 0.944800] mmcblk0: p1 p2 p3
> + [ 0.966696] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem
> + [ 0.974105] EXT4-fs (mmcblk0p3): write access will be enabled during recovery
> + [ 1.052362] random: fast init done
> + [ 1.057961] EXT4-fs (mmcblk0p3): recovery complete
> + [ 1.065734] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
> + [ 1.074002] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
> + [ 1.081654] Freeing unused kernel memory: 168K
> + [ 1.086108] This architecture does not have kernel memory protection.
> + [ 1.092629] Run /sbin/init as init process
> + [ 1.702217] systemd[1]: System time before build time, advancing clock.
> + [ 1.754192] systemd[1]: systemd 244.3+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
> + [ 1.776361] systemd[1]: Detected architecture riscv64.
> +
> + Welcome to OpenEmbedded nodistro.0!
> +
> + [ 1.829651] systemd[1]: Set hostname to <icicle-kit-es>.
> + [ 2.648597] random: systemd: uninitialized urandom read (16 bytes read)
> + [ 2.657485] systemd[1]: Created slice system-getty.slice.
> + [ OK ] Created slice system-getty.slice.
> + [ 2.698779] random: systemd: uninitialized urandom read (16 bytes read)
> + [ 2.706317] systemd[1]: Created slice system-serial\x2dgetty.slice.
> + [ OK ] Created slice system-serial\x2dgetty.slice.
> + [ 2.748716] random: systemd: uninitialized urandom read (16 bytes read)
> + [ 2.756098] systemd[1]: Created slice User and Session Slice.
> + [ OK ] Created slice User and Session Slice.
> + [ 2.789065] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
> + [ OK ] Started Dispatch Password …ts to Console Directory Watch.
> + [ 2.828974] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
> + [ OK ] Started Forward Password R…uests to Wall Directory Watch.
> + [ 2.869009] systemd[1]: Reached target Paths.
> + [ OK ] Reached target Paths.
> + [ 2.898808] systemd[1]: Reached target Remote File Systems.
> + [ OK ] Reached target Remote File Systems.
> + [ 2.938771] systemd[1]: Reached target Slices.
> + [ OK ] Reached target Slices.
> + [ 2.968754] systemd[1]: Reached target Swap.
> + [ OK ] Reached target Swap.
> + [ 2.999283] systemd[1]: Listening on initctl Compatibility Named Pipe.
> + [ OK ] Listening on initctl Compatibility Named Pipe.
> + [ 3.060458] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
> + [ 3.069826] systemd[1]: Listening on Journal Socket (/dev/log).
> + [ OK ] Listening on Journal Socket (/dev/log).
> + [ 3.109601] systemd[1]: Listening on Journal Socket.
> + [ OK ] Listening on Journal Socket.
> + [ 3.149868] systemd[1]: Listening on Network Service Netlink Socket.
> + [ OK ] Listening on Network Service Netlink Socket.
> + [ 3.189419] systemd[1]: Listening on udev Control Socket.
> + [ OK ] Listening on udev Control Socket.
> + [ 3.229179] systemd[1]: Listening on udev Kernel Socket.
> + [ OK ] Listening on udev Kernel Socket.
> + [ 3.269520] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
> + [ 3.278477] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped.
> + [ 3.288200] systemd[1]: Condition check resulted in Kernel Debug File System being skipped.
> + [ 3.302570] systemd[1]: Mounting Temporary Directory (/tmp)...
> + Mounting Temporary Directory (/tmp)...
> + [ 3.339226] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped.
> + [ 3.355883] systemd[1]: Starting File System Check on Root Device...
> + Starting File System Check on Root Device...
> + [ 3.407220] systemd[1]: Starting Journal Service...
> + Starting Journal Service...
> + [ 3.422441] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
> + [ 3.431770] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
> + [ 3.446415] systemd[1]: Mounting Kernel Configuration File System...
> + Mounting Kernel Configuration File System...
> + [ 3.458983] systemd[1]: Starting Apply Kernel Variables...
> + Starting Apply Kernel Variables...
> + [ 3.471368] systemd[1]: Starting udev Coldplug all Devices...
> + Starting udev Coldplug all Devices...
> + [ 3.491071] systemd[1]: Mounted Temporary Directory (/tmp).
> + [ OK 3.498114] systemd[1]: Mounted Kernel Configuration File System.
> + 0m] Mounted Temporary Directory (/tmp).
> + [ OK ] Mounted Kernel Configuration File System.
> + [ 3.550853] systemd[1]: Started Apply Kernel Variables.
> + [ OK 3.557535] systemd[1]: Started Journal Service.
> + 0m] Started Apply Kernel Variables.
> + [ OK ] Started Journal Service.
> + [ OK ] Started udev Coldplug all Devices.
> + [ OK ] Started File System Check on Root Device.
> + Starting Remount Root and Kernel File Systems...
> + [ 8.133469] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
> + [ OK ] Started Remount Root and Kernel File Systems.
> + Starting Flush Journal to Persistent Storage...
> + [ 8.215327] systemd-journald[77]: Received client request to flush runtime journal.
> + Starting Create Static Device Nodes in /dev...
> + [ OK ] Started Flush Journal to Persistent Storage.
> + [ OK ] Started Create Static Device Nodes in /dev.
> + [ OK ] Reached target Local File Systems (Pre).
> + Mounting /var/volatile...
> + Starting udev Kernel Device Manager...
> + [ OK ] Mounted /var/volatile.
> + Starting Load/Save Random Seed...
> + [ OK ] Reached target Local File Systems.
> + Starting Create Volatile Files and Directories...
> + [ OK ] Started udev Kernel Device Manager.
> + [ OK ] Started Create Volatile Files and Directories.
> + Starting Network Time Synchronization...
> + Starting Update UTMP about System Boot/Shutdown...
> + [ OK ] Started Update UTMP about System Boot/Shutdown.
> + [ OK ] Started Network Time Synchronization.
> + [ 11.618575] random: crng init done
> + [ 11.622007] random: 7 urandom warning(s) missed due to ratelimiting
> + [ OK ] Started Load/Save Random Seed.
> + [ OK ] Reached target System Initialization.
> + [ OK ] Started Daily Cleanup of Temporary Directories.
> + [ OK ] Reached target System Time Set.
> + [ OK ] Reached target System Time Synchronized.
> + [ OK ] Reached target Timers.
> + [ OK ] Listening on D-Bus System Message Bus Socket.
> + [ OK ] Listening on dropbear.socket.
> + [ OK ] Reached target Sockets.
> + [ OK ] Reached target Basic System.
> + [ OK ] Started D-Bus System Message Bus.
> + Starting IPv6 Packet Filtering Framework...
> + Starting IPv4 Packet Filtering Framework...
> + Starting Login Service...
> + [ OK ] Started IPv6 Packet Filtering Framework.
> + [ OK ] Started IPv4 Packet Filtering Framework.
> + [ OK ] Reached target Network (Pre).
> + Starting Network Service...
> + [ OK ] Started Login Service.
> + [ 12.602455] macb 20112000.ethernet eth0: PHY [20112000.ethernet-ffffffff:09] driver [Vitesse VSC8662] (irq=POLL)
> + [ 12.612795] macb 20112000.ethernet eth0: configuring for phy/sgmii link mode
> + [ 12.622153] pps pps0: new PPS source ptp0
> + [ OK 12.626725] macb 20112000.ethernet: gem-ptp-timer ptp clock registered.
> + 0m] Started Network Service.
> + Starting Network Name Resolution...
> + [ OK ] Started Network Name Resolution.
> + [ OK ] Reached target Network.
> + [ OK ] Reached target Host and Network Name Lookups.
> + [ OK ] Started Collectd.
> + [ OK ] Started Collectd.
> + Starting Permit User Sessions...
> + [ OK ] Started Permit User Sessions.
> + [ OK ] Started Getty on tty1.
> + [ OK ] Started Serial Getty on ttyS0.
> + [ OK ] Reached target Login Prompts.
> + [ OK ] Reached target Multi-User System.
> + Starting Update UTMP about System Runlevel Changes...
> + [ OK ] Started Update UTMP about System Runlevel Changes.
> +
> + OpenEmbedded nodistro.0 icicle-kit-es ttyS0
> +
> + icicle-kit-es login: [ 15.795564] macb 20112000.ethernet eth0: Link is Up - 1Gbps/Full - flow control tx
> + [ 15.803306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> +
> + icicle-kit-es login: root
> + root at icicle-kit-es:~#
Regards,
Bin
More information about the U-Boot
mailing list