[PATCH v2 14/14] qemu: arm64: Add documentation for capsule update

[Sughosh Ganu]

On Mon, 21 Dec 2020 at 18:28, Heinrich Schuchardt <xypron.glpk at gmx.de>
wrote:

> On 12/21/20 12:43 PM, Sughosh Ganu wrote:
> > Add documentation highlighting the steps for using the uefi capsule
> > update feature for updating the u-boot firmware image.
> >
> > Signed-off-by: Sughosh Ganu <sughosh.ganu at linaro.org>
> > ---
> >
> > Changes since V1:
> > * Change the documentation to reflect the usage of overlays for
> >    embedding the public key certs at runtime
> > * Fix the build for 'make htmldocs'
> >
> >   doc/board/emulation/qemu-arm.rst | 188 +++++++++++++++++++++++++++++++
>
> Why do you put the information into doc/board/emulation/qemu-arm.rst?
>
> Isn't the same applicable to RISC-V QEMU?
>

Where do you want me to put it. Currently, I do not see any common document
for qemu which can be shared between qemu-arm and qemu risc-v. Or do you
think a new document should be created under doc/board/emulation/
directory. Moreover, my series is adding support for capsule update feature
on the qemu arm64 platform, and i have only tested this feature on the qemu
arm64 platform. If someone wants to extend this on the qemu
risc-v platform, that work i think needs to be done separately, with
whatever changes that may be needed to get capsule updates working on qemu
risc-v. If you so prefer, I can move the changes made for mtdparts and
dfu(patches 4/14 and 5/14) under a common directory under board/emulation.

-sughosh


>
> Best regards
>
> Heinrich
>
> >   1 file changed, 188 insertions(+)
> >
> > diff --git a/doc/board/emulation/qemu-arm.rst
> b/doc/board/emulation/qemu-arm.rst
> > index 8d7fda10f1..11d91811b3 100644
> > --- a/doc/board/emulation/qemu-arm.rst
> > +++ b/doc/board/emulation/qemu-arm.rst
> > @@ -90,3 +90,191 @@ The debug UART on the ARM virt board uses these
> settings::
> >       CONFIG_DEBUG_UART_PL010=y
> >       CONFIG_DEBUG_UART_BASE=0x9000000
> >       CONFIG_DEBUG_UART_CLOCK=0
> > +
> > +Enabling Uefi Capsule Update feature
> > +------------------------------------
> > +
> > +Support has been added for the uefi capsule update feature which
> > +enables updating the u-boot image using the uefi firmware management
> > +protocol (fmp). The capsules are not passed to the firmware through
> > +the UpdateCapsule runtime service. Instead, capsule-on-disk
> > +functionality is used for fetching the capsule from the EFI System
> > +Partition (ESP).
> > +
> > +Currently, support has been added for updating the u-boot binary as a
> > +raw image when the platform is booted in non-secure mode, i.e with
> > +CONFIG_TFABOOT disabled. For this configuration, the qemu platform
> > +needs to be booted with 'secure=off'. The u-boot binary placed on the
> > +first bank of the Nor Flash at offset 0x0. The u-boot environment is
> > +placed on the second Nor Flash bank at offset 0x4000000.
> > +
> > +The capsule update feature is enabled with the following configs::
> > +
> > +    CONFIG_MTD=y
> > +    CONFIG_FLASH_CFI_MTD=y
> > +    CONFIG_CMD_MTDPARTS=y
> > +    CONFIG_CMD_DFU=y
> > +    CONFIG_DFU_MTD=y
> > +    CONFIG_PCI_INIT_R=y
> > +    CONFIG_EFI_CAPSULE_ON_DISK=y
> > +    CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y
> > +    CONFIG_EFI_CAPSULE_FIRMWARE=y
> > +    CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y
> > +    CONFIG_EFI_CAPSULE_FMP_HEADER=y
> > +
> > +In addition, the following config needs to be disabled::
> > +
> > +    CONFIG_TFABOOT
> > +
> > +The capsule file can be generated by using the GenerateCapsule.py
> > +script in edk2::
> > +
> > +    $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \
> > +    <capsule_file_name> --fw-version <val> --lsv <val> --guid \
> > +    e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose --update-image-index
> \
> > +    <val> --verbose <u-boot.bin>
> > +
> > +As per the uefi specification, the capsule file needs to be placed on
> > +the EFI System Partition, under the EFI/UpdateCapsule/ directory. The
> > +EFI System Partition can be a virtio-blk-device.
> > +
> > +Before initiating the firmware update, the efi variables BootNext,
> > +BootXXXX and OsIndications need to be set. The BootXXXX variable needs
> > +to be pointing to the EFI System Partition which contains the capsule
> > +file. The BootNext, BootXXXX and OsIndications variables can be set
> > +using the following commands::
> > +
> > +    => efidebug boot add 0 Boot0000 virtio 0:1 <capsule_file_name>
> > +    => efidebug boot next 0
> > +    => setenv -e -nv -bs -rt -v OsIndications =0x04
> > +    => saveenv
> > +
> > +Finally, the capsule update can be initiated with the following
> > +command::
> > +
> > +    => efidebug capsule disk-update
> > +
> > +The updated u-boot image will be booted on subsequent boot.
> > +
> > +Enabling Capsule Authentication
> > +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > +
> > +The uefi specification defines a way of authenticating the capsule to
> > +be updated by verifying the capsule signature. The capsule signature
> > +is computed and prepended to the capsule payload at the time of
> > +capsule generation. This signature is then verified by using the
> > +public key stored as part of the X509 certificate. This certificate is
> > +in the form of an efi signature list (esl) file, which is embedded as
> > +part of the platform's device tree blob using the mkeficapsule
> > +utility.
> > +
> > +On the qemu virt platforms, the device-tree is generated on the fly
> > +based on the devices configured. This device tree is then passed on to
> > +the various software components booting on the platform, including
> > +u-boot. Therefore, on the qemu virt platform, the signatute is
> > +embedded on an overlay. This overlay is then applied at runtime to the
> > +base platform device-tree. Steps needed for embedding the esl file in
> > +the overlay are highlighted below.
> > +
> > +The capsule authentication feature can be enabled through the
> > +following config, in addition to the configs listed above for capsule
> > +update::
> > +
> > +    CONFIG_EFI_CAPSULE_AUTHENTICATE=y
> > +
> > +The public and private keys used for the signing process are generated
> > +and used by the steps highlighted below::
> > +
> > +    1. Install utility commands on your host
> > +       * openssl
> > +       * efitools
> > +
> > +    2. Create signing keys and certificate files on your host
> > +
> > +        $ openssl req -x509 -sha256 -newkey rsa:2048 -subj /CN=CRT/ \
> > +            -keyout CRT.key -out CRT.crt -nodes -days 365
> > +        $ cert-to-efi-sig-list CRT.crt CRT.esl
> > +
> > +        $ openssl x509 -in CRT.crt -out CRT.cer -outform DER
> > +        $ openssl x509 -inform DER -in CRT.cer -outform PEM -out
> CRT.pub.pem
> > +
> > +        $ openssl pkcs12 -export -out CRT.pfx -inkey CRT.key -in CRT.crt
> > +        $ openssl pkcs12 -in CRT.pfx -nodes -out CRT.pem
> > +
> > +The capsule file can be generated by using the GenerateCapsule.py
> > +script in edk2::
> > +
> > +    $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \
> > +      <capsule_file_name> --monotonic-count <val> --fw-version \
> > +      <val> --lsv <val> --guid \
> > +      e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose \
> > +      --update-image-index <val> --signer-private-cert \
> > +      /path/to/CRT.pem --trusted-public-cert \
> > +      /path/to/CRT.pub.pem --other-public-cert /path/to/CRT.pub.pem \
> > +      <u-boot.bin>
> > +
> > +Place the capsule generated in the above step on the EFI System
> > +Partition under the EFI/UpdateCapsule directory
> > +
> > +For embedding the public key certificate, the following steps need to
> > +be followed::
> > +
> > +    1. Generate a skeleton overlay dts file, with a single fragment
> > +       node and an empty __overlay__ node
> > +
> > +    2. Convert the dts to a corresponding dtb with the following
> > +       command
> > +        ./scripts/dtc/dtc -@ -I dts -O dtb -o <ov_dtb_file_name> \
> > +        <dts_file>
> > +
> > +    3. Run the dtb file generated above through the mkeficapsule tool
> > +       in u-boot
> > +        ./tools/mkeficapsule -O <pub_key.esl> -D <ov_dtb>
> > +
> > +Running the above command results in the creation of a 'signature'
> > +node in the dtb, under which the public key is stored as a
> > +'capsule-key' property. The '-O' option is to be used since the
> > +public key certificate(esl) file is being embedded in an overlay.
> > +
> > +The dtb file embedded with the certificate is now to be placed on an
> > +EFI System Partition. This would then be loaded and "merged" with the
> > +base platform fdt at runtime.
> > +
> > +Build u-boot with the following steps::
> > +
> > +    $ make qemu_arm64_defconfig
> > +    $ make menuconfig
> > +        Disable CONFIG_TFABOOT
> > +        Enable CONFIG_EFI_CAPSULE_AUTHENTICATE
> > +        Enable all configs needed for capsule update(listed above)
> > +    $ make all
> > +
> > +Boot the platform and perform the following steps on the u-boot
> > +command line::
> > +
> > +    1. Enable capsule authentication by setting the following env
> > +       variable
> > +
> > +        => setenv capsule_authentication_enabled 1
> > +        => saveenv
> > +
> > +    2. Load the overlay dtb to memory and merge it with the base fdt
> > +
> > +        => fatload virtio 0:1 <$fdtovaddr> EFI/<ov_dtb_file>
> > +        => fdt addr $fdtcontroladdr
> > +        => fdt resize <size_of_ov_dtb_file>
> > +        => fdt apply <$fdtovaddr>
> > +
> > +    3. Set the following env and efi Boot variables
> > +
> > +        => setenv -e -nv -bs -rt -v OsIndications =0x04
> > +        => efidebug boot add 0 Boot0000 virtio 0:1 <capsule_file_name>
> > +        => efidebug boot next 0
> > +        => saveenv
> > +
> > +    4. Finally, the capsule update can be initiated with the following
> > +       command
> > +
> > +        => efidebug capsule disk-update
> > +
> > +On subsequent reboot, the platform should boot the updated u-boot
> binary.
> >
>
>