[PATCH v2 03/12] ARM: mach-k3: sysfw-loader: Use SPI memmapped addr when loading SYSFW

[Vignesh Raghavendra]

From: Lokesh Vutla <lokeshvutla at ti.com>

Since ROM configures OSPI controller to be in memory mapped mode in OSPI
boot, R5 SPL can directly pass the memory mapped pointer to ROM. With
this ROM can directly pull the SYSFW image from OSPI.

Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr at ti.com>
---
 arch/arm/mach-k3/Kconfig        |  8 ++++++++
 arch/arm/mach-k3/sysfw-loader.c | 31 ++++++++++++++++++++++++++++++-
 2 files changed, 38 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-k3/Kconfig b/arch/arm/mach-k3/Kconfig
index 2e111bbf27ee..c98a5c66749f 100644
--- a/arch/arm/mach-k3/Kconfig
+++ b/arch/arm/mach-k3/Kconfig
@@ -126,6 +126,14 @@ config K3_SYSFW_IMAGE_SIZE_MAX
 	  tree blob. Keep it as tight as possible, as this directly affects the
 	  overall SPL memory footprint.
 
+config K3_SYSFW_IMAGE_SPI_OFFS
+	hex "SPI offset of SYSFW firmware and configuration blob"
+	depends on K3_LOAD_SYSFW
+	default	0x6C0000
+	help
+	  Offset of the combined System Firmware and configuration image tree
+	  blob to be loaded when booting from a SPI flash memory.
+
 config SYS_K3_SPL_ATF
 	bool "Start Cortex-A from SPL"
 	depends on SPL && CPU_V7R
diff --git a/arch/arm/mach-k3/sysfw-loader.c b/arch/arm/mach-k3/sysfw-loader.c
index 94dbeb9437d9..3677a37f55a2 100644
--- a/arch/arm/mach-k3/sysfw-loader.c
+++ b/arch/arm/mach-k3/sysfw-loader.c
@@ -14,6 +14,8 @@
 #include <g_dnl.h>
 #include <usb.h>
 #include <dfu.h>
+#include <dm/uclass-internal.h>
+#include <spi_flash.h>
 
 #include <asm/arch/sys_proto.h>
 #include "common.h"
@@ -197,12 +199,32 @@ exit:
 }
 #endif
 
+#if CONFIG_IS_ENABLED(SPI_LOAD)
+static void *k3_sysfw_get_spi_addr(void)
+{
+	struct udevice *dev;
+	fdt_addr_t addr;
+	int ret;
+
+	ret = uclass_find_device_by_seq(UCLASS_SPI, CONFIG_SF_DEFAULT_BUS,
+					true, &dev);
+	if (ret)
+		return NULL;
+
+	addr = dev_read_addr_index(dev, 1);
+	if (addr == FDT_ADDR_T_NONE)
+		return NULL;
+
+	return (void *)(addr + CONFIG_K3_SYSFW_IMAGE_SPI_OFFS);
+}
+#endif
+
 void k3_sysfw_loader(void (*config_pm_done_callback)(void))
 {
 	struct spl_image_info spl_image = { 0 };
 	struct spl_boot_device bootdev = { 0 };
 	struct ti_sci_handle *ti_sci;
-	int ret;
+	int ret = 0;
 
 	/* Reserve a block of aligned memory for loading the SYSFW image */
 	sysfw_load_address = memalign(ARCH_DMA_MINALIGN,
@@ -243,6 +265,13 @@ void k3_sysfw_loader(void (*config_pm_done_callback)(void))
 #endif
 		break;
 #endif
+#if CONFIG_IS_ENABLED(SPI_LOAD)
+	case BOOT_DEVICE_SPI:
+		sysfw_load_address = k3_sysfw_get_spi_addr();
+		if (!sysfw_load_address)
+			ret = -ENODEV;
+		break;
+#endif
 #if CONFIG_IS_ENABLED(YMODEM_SUPPORT)
 	case BOOT_DEVICE_UART:
 #ifdef CONFIG_K3_EARLY_CONS
-- 
2.25.0