[PATCH] net: pfe_eth: Use spi_flash_read API to access flash memory

[Schrempf Frieder]

On 11.12.19 12:53, Kuldeep Singh wrote:
> Current PFE firmware access spi-nor memory directly. New spi-mem
> framework does not support direct memory access. So, let's use
> spi_flash_read API to access memory instead of directly using it.
> 
> Signed-off-by: Kuldeep Singh <kuldeep.singh at nxp.com>
> ---
>   drivers/net/pfe_eth/pfe_firmware.c | 44 +++++++++++++++++++++++++++++-
>   include/configs/ls1012a_common.h   |  5 +++-
>   2 files changed, 47 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/net/pfe_eth/pfe_firmware.c b/drivers/net/pfe_eth/pfe_firmware.c
> index e4563f192b..61d1b96305 100644
> --- a/drivers/net/pfe_eth/pfe_firmware.c
> +++ b/drivers/net/pfe_eth/pfe_firmware.c
> @@ -12,13 +12,14 @@
>   
>   #include <net/pfe_eth/pfe_eth.h>
>   #include <net/pfe_eth/pfe_firmware.h>
> +#include <spi_flash.h>
>   #ifdef CONFIG_CHAIN_OF_TRUST
>   #include <fsl_validate.h>
>   #endif
>   
>   #define PFE_FIRMWARE_FIT_CNF_NAME	"config at 1"
>   
> -static const void *pfe_fit_addr = (void *)CONFIG_SYS_LS_PFE_FW_ADDR;
> +static const void *pfe_fit_addr;
>   
>   /*
>    * PFE elf firmware loader.
> @@ -159,6 +160,43 @@ static int pfe_fit_check(void)
>   	return ret;
>   }
>   
> +int pfe_spi_flash_init(void)
> +{
> +	struct spi_flash *pfe_flash;
> +	int ret = 0;
> +	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
> +
> +#ifdef CONFIG_DM_SPI_FLASH
> +	struct udevice *new;
> +
> +	/* speed and mode will be read from DT */
> +	ret = spi_flash_probe_bus_cs(CONFIG_ENV_SPI_BUS,
> +				     CONFIG_ENV_SPI_CS, 0, 0, &new);
> +
> +	pfe_flash = dev_get_uclass_priv(new);
> +#else
> +	pfe_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS,
> +				    CONFIG_ENV_SPI_CS,
> +				    CONFIG_ENV_SPI_MAX_HZ,
> +				    CONFIG_ENV_SPI_MODE);
> +#endif
> +	if (!pfe_flash) {
> +		printf("SF: probe for pfe ucode failed\n");

I think you should return some error code in this case. Currently ret 
could still be 0 at this point.

> +	} else {
> +		ret = spi_flash_read(pfe_flash,
> +				     CONFIG_SYS_LS_PFE_FW_ADDR,
> +				     CONFIG_SYS_QE_FMAN_FW_LENGTH,
> +				     addr);
> +		if (ret)
> +			printf("SF: read for ucode failed\n");
> +
> +		pfe_fit_addr = addr;
> +		spi_flash_free(pfe_flash);
> +	}
> +
> +	return ret;
> +}
> +
>   /*
>    * PFE firmware initialization.
>    * Loads different firmware files from FIT image.
> @@ -183,6 +221,10 @@ int pfe_firmware_init(void)
>   	int ret = 0;
>   	int fw_count;
>   
> +	ret = pfe_spi_flash_init();
> +	if (ret)
> +		goto err;
> +
>   	ret = pfe_fit_check();
>   	if (ret)
>   		goto err;
> diff --git a/include/configs/ls1012a_common.h b/include/configs/ls1012a_common.h
> index 2579e2fb37..cbc5bff21c 100644
> --- a/include/configs/ls1012a_common.h
> +++ b/include/configs/ls1012a_common.h
> @@ -36,9 +36,12 @@
>   /* Size of malloc() pool */
>   #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128 * 1024)
>   
> +/* PFE */
> +#define CONFIG_SYS_FMAN_FW_ADDR		0x400d0000
> +#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
> +
>   /*SPI device */
>   #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_TFABOOT)
> -#define CONFIG_SYS_FMAN_FW_ADDR		0x400d0000
>   #define CONFIG_SPI_FLASH_SPANSION
>   #define CONFIG_FSL_SPI_INTERFACE
>   #define CONFIG_SF_DATAFLASH
>