U-Boot: wandboard ethernet problem with newest mainline

[Heiko Schocher]

Hi Fabio!

happy new year! Hope you are fine?

I just builded the newest mainline U-Boot code for the wandboard, and
I get:

U-Boot SPL 2020.01-tbot-00271-gd8a3f52 (Jan 08 2020 - 06:33:42 +0100)
Trying to boot from MMC1


U-Boot 2020.01-tbot-00271-gd8a3f52 (Jan 08 2020 - 06:33:42 +0100)

CPU:   Freescale i.MX6DL rev1.3 at 792 MHz
Reset cause: WDOG
DRAM:  1 GiB
PMIC:  pmic_get() ret -19
MMC:   FSL_SDHC: 2, FSL_SDHC: 1, FSL_SDHC: 0
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Model: Wandboard i.MX6 Dual Lite Board rev B1
Board: Wandboard rev B1
Net:   Could not get PHY for FEC0: addr 1
Could not get PHY for FEC0: addr 1
No ethernet found.

Hit any key to stop autoboot:  0
=>

Ethernet does not work, also pmic setup seems buggy... Hmm pmic is not
detected, and later board revision is B1 instead D1... I think thats
the root cause of the problem...

Attached a bootlog from an older, working version [1].

Ok, I tried to bisect it, but bisecting does not work, as there are
commits, which does not build for wandboard :-(

Looking into git history, there is a commit from you:

commit 5b858582512883b8a85d74e108873f9beed1e954
Author: Fabio Estevam <festevam at gmail.com>
Date:   Wed Jun 12 12:34:40 2019 -0300

     wandboard: Add FIT image support

     After the transition to DM, only the mx6dl/solo wandboard
     is supported.

     Add FIT image support so that all the wandboard variants
     can be supported, like it was prior to the DM conversion.

     Successfully booted Linux on mx6q/solo/qp wandboards.

So it worked for you? I flashed the u-boot-fit-dtb.bin instead of
u-boot-dtb.bin, but this leads to:

resetting ...

U-Boot SPL 2020.01-tbot-00271-gd8a3f52 (Jan 08 2020 - 06:25:09 +0100)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
spl: ext4fs_open failed
spl_load_image_ext: error reading image u-boot-dtb.img, err - -1
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Same with u-boot-with-spl.imx flashed.

I am sure I make here something wrong... any ideas?

Attached also a working bootlog with an older version [1].

Thanks!

bye,
Heiko

[1] working U-Boot bootlog:
U-Boot SPL 2019.04-rc4-tbot-00111-gab8fc41 (Jan 08 2020 - 06:18:50 +0100)
Trying to boot from MMC1


U-Boot 2019.04-rc4-tbot-00111-gab8fc41 (Jan 08 2020 - 06:18:50 +0100)

CPU:   Freescale i.MX6DL rev1.3 at 792 MHz
Reset cause: WDOG
I2C:   ready
DRAM:  1 GiB
PMIC:  PFUZE100 ID=0x10
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Board: Wandboard rev D1
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
=>

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: hs at denx.de