[PATCH v2 11/21] dts: mtmips: remove all unusable nodes and properties from mt7628s.dtsi
Weijie Gao
weijie.gao at mediatek.com
Sun Jan 19 03:14:49 CET 2020
On Fri, 2020-01-17 at 15:42 +0100, Stefan Roese wrote:
> On 17.01.20 08:45, Weijie Gao wrote:
> > This patch removes all unused and unusable nodes and properties from
> > mt7628s.dtsi.
> >
> > Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
> > ---
> > Changes since v1: splitted from another patch
>
> Please don't remove the unused parts. As mentioned before, we try to
> stay as close to the official DT files from the Linux tree as possible.
> Goal is to sync with Linux at some time. This is already done on other
> architectures / boards.
OK. I'll drop this one.
>
> Thanks,
> Stefan
>
> > ---
> > arch/mips/dts/mt7628a.dtsi | 68 --------------------------------------
> > 1 file changed, 68 deletions(-)
> >
> > diff --git a/arch/mips/dts/mt7628a.dtsi b/arch/mips/dts/mt7628a.dtsi
> > index cdc643fe37..3d7b839e6d 100644
> > --- a/arch/mips/dts/mt7628a.dtsi
> > +++ b/arch/mips/dts/mt7628a.dtsi
> > @@ -7,24 +7,6 @@
> > #size-cells = <1>;
> > compatible = "ralink,mt7628a-soc";
> >
> > - cpus {
> > - #address-cells = <1>;
> > - #size-cells = <0>;
> > -
> > - cpu at 0 {
> > - compatible = "mti,mips24KEc";
> > - device_type = "cpu";
> > - reg = <0>;
> > - };
> > - };
> > -
> > - cpuintc: interrupt-controller {
> > - #address-cells = <0>;
> > - #interrupt-cells = <1>;
> > - interrupt-controller;
> > - compatible = "mti,cpu-interrupt-controller";
> > - };
> > -
> > clk48m: clk48m at 0 {
> > compatible = "fixed-clock";
> >
> > @@ -41,11 +23,6 @@
> > #address-cells = <1>;
> > #size-cells = <1>;
> >
> > - sysc: system-controller at 0 {
> > - compatible = "ralink,mt7620a-sysc", "syscon";
> > - reg = <0x0 0x100>;
> > - };
> > -
> > resetctl-reboot {
> > compatible = "resetctl-reboot";
> >
> > @@ -223,32 +200,6 @@
> >
> > resets = <&rstctrl MT7628_TIMER_RST>;
> > reset-names = "wdt";
> > -
> > - interrupt-parent = <&intc>;
> > - interrupts = <24>;
> > - };
> > -
> > - intc: interrupt-controller at 200 {
> > - compatible = "ralink,rt2880-intc";
> > - reg = <0x200 0x100>;
> > -
> > - interrupt-controller;
> > - #interrupt-cells = <1>;
> > -
> > - resets = <&rstctrl MT7628_INT_RST>;
> > - reset-names = "intc";
> > -
> > - interrupt-parent = <&cpuintc>;
> > - interrupts = <2>;
> > -
> > - ralink,intc-registers = <0x9c 0xa0
> > - 0x6c 0xa4
> > - 0x80 0x78>;
> > - };
> > -
> > - memory-controller at 300 {
> > - compatible = "ralink,mt7620a-memc";
> > - reg = <0x300 0x100>;
> > };
> >
> > gpio at 600 {
> > @@ -261,9 +212,6 @@
> > resets = <&rstctrl MT7628_PIO_RST>;
> > reset-names = "pio";
> >
> > - interrupt-parent = <&intc>;
> > - interrupts = <6>;
> > -
> > gpio0: bank at 0 {
> > reg = <0>;
> > compatible = "mtk,mt7621-gpio-bank";
> > @@ -311,9 +259,6 @@
> > resets = <&rstctrl MT7628_UART0_RST>;
> > reset-names = "uart0";
> >
> > - interrupt-parent = <&intc>;
> > - interrupts = <20>;
> > -
> > reg-shift = <2>;
> > };
> >
> > @@ -329,9 +274,6 @@
> > resets = <&rstctrl MT7628_UART1_RST>;
> > reset-names = "uart1";
> >
> > - interrupt-parent = <&intc>;
> > - interrupts = <21>;
> > -
> > reg-shift = <2>;
> > };
> >
> > @@ -347,9 +289,6 @@
> > resets = <&rstctrl MT7628_UART2_RST>;
> > reset-names = "uart2";
> >
> > - interrupt-parent = <&intc>;
> > - interrupts = <22>;
> > -
> > reg-shift = <2>;
> > };
> > };
> > @@ -361,8 +300,6 @@
> >
> > resets = <&rstctrl MT7628_EPHY_RST>;
> > reset-names = "ephy";
> > -
> > - syscon = <&sysc>;
> > };
> >
> > usb_phy: usb-phy at 10120000 {
> > @@ -371,8 +308,6 @@
> >
> > #phy-cells = <0>;
> >
> > - ralink,sysctl = <&sysc>;
> > -
> > resets = <&rstctrl MT7628_UPHY_RST>;
> > reset-names = "phy";
> >
> > @@ -386,9 +321,6 @@
> >
> > phys = <&usb_phy>;
> > phy-names = "usb";
> > -
> > - interrupt-parent = <&intc>;
> > - interrupts = <18>;
> > };
> >
> > mmc: mmc at 10130000 {
> >
>
> Viele Grüße,
> Stefan
>
More information about the U-Boot
mailing list