[PATCH] ARM: dts: sunxi: Sync R40 dts(i) from v5.4

Jagan Teki jagan at amarulasolutions.com
Tue Jan 21 09:35:12 CET 2020 

Sync R40 dts(i) files from linux-next v5.4 tag.

This sync would update r40 dts(i) and v40-bananapi-m2-berry
dts files.

Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
 arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts |   7 +-
 arch/arm/dts/sun8i-r40.dtsi                  |  24 ++--
 arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts | 135 ++++++++++++++++---
 3 files changed, 136 insertions(+), 30 deletions(-)

diff --git a/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts
index c488aaacbd..42d62d1ba1 100644
--- a/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -201,10 +201,15 @@
 &pio {
 	pinctrl-names = "default";
 	pinctrl-0 = <&clk_out_a_pin>;
+	vcc-pa-supply = <&reg_aldo2>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pe-supply = <&reg_eldo1>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_dldo1>;
 };
 
 &reg_aldo2 {
-	regulator-always-on;
 	regulator-min-microvolt = <2500000>;
 	regulator-max-microvolt = <2500000>;
 	regulator-name = "vcc-pa";
diff --git a/arch/arm/dts/sun8i-r40.dtsi b/arch/arm/dts/sun8i-r40.dtsi
index 06b685869f..c9c2688db6 100644
--- a/arch/arm/dts/sun8i-r40.dtsi
+++ b/arch/arm/dts/sun8i-r40.dtsi
@@ -119,10 +119,10 @@
 			compatible = "allwinner,sun8i-r40-de2-clk",
 				     "allwinner,sun8i-h3-de2-clk";
 			reg = <0x01000000 0x100000>;
-			clocks = <&ccu CLK_DE>,
-				 <&ccu CLK_BUS_DE>;
-			clock-names = "mod",
-				      "bus";
+			clocks = <&ccu CLK_BUS_DE>,
+				 <&ccu CLK_DE>;
+			clock-names = "bus",
+				      "mod";
 			resets = <&ccu RST_BUS_DE>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -322,8 +322,7 @@
 		};
 
 		rtc: rtc at 1c20400 {
-			compatible = "allwinner,sun8i-r40-rtc",
-				     "allwinner,sun8i-h3-rtc";
+			compatible = "allwinner,sun8i-r40-rtc";
 			reg = <0x01c20400 0x400>;
 			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 			clock-output-names = "osc32k", "osc32k-out";
@@ -409,6 +408,8 @@
 		wdt: watchdog at 1c20c90 {
 			compatible = "allwinner,sun4i-a10-wdt";
 			reg = <0x01c20c90 0x10>;
+			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
 		};
 
 		uart0: serial at 1c28000 {
@@ -562,9 +563,7 @@
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SATA>, <&ccu CLK_SATA>;
 			resets = <&ccu RST_BUS_SATA>;
-			resets-name = "ahci";
-			#address-cells = <1>;
-			#size-cells = <0>;
+			reset-names = "ahci";
 			status = "disabled";
 
 		};
@@ -614,12 +613,9 @@
 				#size-cells = <0>;
 
 				tcon_top_mixer0_in: port at 0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					tcon_top_mixer0_in_mixer0: endpoint at 0 {
-						reg = <0>;
+					tcon_top_mixer0_in_mixer0: endpoint {
 						remote-endpoint = <&mixer0_out_tcon_top>;
 					};
 				};
@@ -818,7 +814,7 @@
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
-			phy-names = "hdmi-phy";
+			phy-names = "phy";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts
index 54ad4db468..15c22b06fc 100644
--- a/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -50,6 +50,7 @@
 	compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40";
 
 	aliases {
+		ethernet0 = &gmac;
 		serial0 = &uart0;
 	};
 
@@ -57,6 +58,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -84,12 +96,18 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "ext_clock";
 	};
 };
 
 &ahci {
-	phy-supply = <&reg_eldo3>;	/* VDD12-SATA */
-	ahci-supply = <&reg_dldo4>;	/* VDD25-SATA */
+	ahci-supply = <&reg_dldo4>;
+	phy-supply = <&reg_eldo3>;
+	status = "okay";
+};
+
+&de {
 	status = "okay";
 };
 
@@ -98,6 +116,32 @@
 	status = "okay";
 };
 
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii";
+	phy-supply = <&reg_dc1sw>;
+	status = "okay";
+};
+
+&gmac_mdio {
+	phy1: ethernet-phy at 1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -111,6 +155,41 @@
 
 #include "axp22x.dtsi"
 
+&mmc0 {
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pg_pins>;
+	vmmc-supply = <&reg_dldo2>;
+	vqmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clk_out_a_pin>;
+	vcc-pa-supply = <&reg_aldo2>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pe-supply = <&reg_eldo1>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_dldo1>;
+};
+
+&reg_aldo2 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pa";
+};
+
 &reg_aldo3 {
 	regulator-always-on;
 	regulator-min-microvolt = <2700000>;
@@ -118,6 +197,12 @@
 	regulator-name = "avcc";
 };
 
+&reg_dc1sw {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-gmac-phy";
+};
+
 &reg_dcdc1 {
 	regulator-always-on;
 	regulator-min-microvolt = <3000000>;
@@ -152,12 +237,27 @@
 	regulator-name = "vcc-wifi-io";
 };
 
+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
 &reg_dldo2 {
+	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-wifi";
 };
 
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-2";
+};
+
 &reg_dldo4 {
 	regulator-min-microvolt = <2500000>;
 	regulator-max-microvolt = <2500000>;
@@ -170,28 +270,33 @@
 	regulator-name = "vdd1v2-sata";
 };
 
-&mmc0 {
-	vmmc-supply = <&reg_dcdc1>;
-	bus-width = <4>;
-	cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */
+&tcon_tv0 {
 	status = "okay";
 };
 
-&mmc1 {
+&uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pg_pins>;
-	vmmc-supply = <&reg_dldo2>;
-	vqmmc-supply = <&reg_dldo1>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
-&uart0 {
+&uart3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;
+	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_dldo2>;
+		vddio-supply = <&reg_dldo1>;
+		device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		/* TODO host wake line connected to PMIC GPIO pins */
+		shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
+		max-speed = <1500000>;
+	};
 };
 
 &usbphy {
-- 
2.18.0.321.gffc6fa0e3

More information about the U-Boot mailing list