[PATCH v2 0/3] Ethernet support for Raspberry Pi 4

[Andre Przywara]

On Wed, 22 Jan 2020 18:18:39 +0100
Matthias Brugger <mbrugger at suse.com> wrote:

Hi Matthias,

> On 17/01/2020 02:20, Andre Przywara wrote:
> > This series adds Ethernet support for the Raspberry Pi 4. The SoC
> > includes a "Broadcom Genet v5 MAC" IP, connected as a proper platform
> > device (no USB anymore!). Patch 1 provides a driver for that. There does
> > not seem to be publicly available documentation, so this is based on the
> > Linux driver, but stripped down to just provide what U-Boot needs.
> > Patch 2 fixes up the RPi4 memory map to accommodate the MMIO area the
> > MAC lives in, while patch 3 enables it in the respective defconfigs.
> > 
> > This version addresses the comments by the diligent reviewers and testers,
> > for a changelog see below.
> > To see the individual changes as patches, refer to [1].
> > 
> > Please have a look and test it, I hope this helps to simplify
> > development, as you spare the SD card and its slot from heavy swapping.
> > 
> > I dropped the Tested-by's, as there were changes in the code. Happy
> > to reapply them when people confirm that it still works for them.
> >   
> 
> I having problems to actually boot a kernel when the genet driver is build into
> U-Boot.

Ah! Sorry, I misread the former reports, I thought this was about booting kernels in general, with mainline U-Boot, without this series.

> If I boot grub and linux-next from there, I get the following SError (when using
> earlycon):
> https://pastebin.com/c1sw2uZk
> 
> If I skip grub and boot the kernel directly from the SD:
> load mmc 0:1 $kernel_addr_r Image
> load mmc 0:1 $fdt_addr_r bcm2711-rpi-4-b.dtb
> setenv bootargs "earlycon=uart8250,mmio32,0xfe215040"
> booti $kernel_addr_r - $fdt_addr_r
> 
> Gives a similar result.
> 
> Do you see similar issues?

I didn't manage to start some kernel even without this series, I think, but didn't investigate further. I *loaded* several kernel images via TFTP and verified them with md5sum.

Some questions:
- Does this happen even without touching the Ethernet in U-Boot at all (no dhcp command, no tftpboot, etc.)?
  (I wonder if we have still DMA going on, even after the kernel already started. But if we just call probe(), there shouldn't be much going on).
- Does reverting patch 2/3 change anything?
- Does TFTP load work in grub? (net_bootp efinet0; set net_default_server=<IP address>; linux (tftp)/Image-5.5-rc7 ....)

I will try to debug this later tonight.

Thanks!
Andre.

> 
> Regards,
> Matthias
> 
> > Cheers,
> > Andre.
> > 
> > [1] https://github.com/apritzel/u-boot/commits/rpi4-eth-v2
> > 
> > Changelog v1 ... v2:
> > - use native endianess functions when accessing MMIO registers
> > - use dev_* DM wrappers for accessing devicetree data
> > - round base and length for flush_dcache_range, plus a comment
> > - check and round length for invalidate_cache_range
> > - support RGMII_RXID PHY mode, to support mainline .dtb
> > 
> > Amit Singh Tomar (3):
> >   net: Add support for Broadcom GENETv5 Ethernet controller
> >   rpi4: Update memory map to accommodate scb devices
> >   rpi4: Enable GENET Ethernet controller
> > 
> >  arch/arm/mach-bcm283x/init.c |   6 +-
> >  configs/rpi_4_32b_defconfig  |   2 +
> >  configs/rpi_4_defconfig      |   2 +
> >  configs/rpi_arm64_defconfig  |   1 +
> >  drivers/net/Kconfig          |   7 +
> >  drivers/net/Makefile         |   1 +
> >  drivers/net/bcmgenet.c       | 722 +++++++++++++++++++++++++++++++++++++++++++
> >  7 files changed, 738 insertions(+), 3 deletions(-)
> >  create mode 100644 drivers/net/bcmgenet.c
> >