[PATCH v2 7/7] board: presidio-asic: Add basic G3 engr. development board support

Daniel Schwierzeck daniel.schwierzeck at gmail.com
Wed Jan 22 22:24:17 CET 2020



Am 21.01.20 um 11:19 schrieb Alex Nemirovsky:
> Add basic Presidio G3 engineering board support
> 
> Signed-off-by: Alex Nemirovsky <alex.nemirovsky at cortina-access.com>
> ---
> 
> Changes in v2: None
> 
>  arch/arm/Kconfig                             |   5 ++
>  arch/arm/dts/Makefile                        |   2 +
>  arch/arm/dts/ca-presidio-engboard.dts        |  69 +++++++++++++++
>  board/cortina/common/armv8/ca7774_regs.h     |  18 ++++
>  board/cortina/presidio-asic/Kconfig          |  20 +++++
>  board/cortina/presidio-asic/MAINTAINERS      |   6 ++
>  board/cortina/presidio-asic/Makefile         |   8 ++
>  board/cortina/presidio-asic/presidio.c       | 126 +++++++++++++++++++++++++++
>  configs/cortina_presidio-asic-base_defconfig |  45 ++++++++++
>  include/configs/presidio_asic.h              | 123 ++++++++++++++++++++++++++
>  10 files changed, 422 insertions(+)
>  create mode 100644 arch/arm/dts/ca-presidio-engboard.dts
>  create mode 100644 board/cortina/common/armv8/ca7774_regs.h
>  create mode 100644 board/cortina/presidio-asic/Kconfig
>  create mode 100644 board/cortina/presidio-asic/MAINTAINERS
>  create mode 100644 board/cortina/presidio-asic/Makefile
>  create mode 100644 board/cortina/presidio-asic/presidio.c
>  create mode 100644 configs/cortina_presidio-asic-base_defconfig
>  create mode 100644 include/configs/presidio_asic.h
> 
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 36c9c2f..6d95cde 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -1638,6 +1638,10 @@ config TARGET_DURIAN
>  	  Support for durian platform.
>  	  It has 2GB Sdram, uart and pcie.
>  
> +config TARGET_PRESIDIO_ASIC
> +	bool "Support Cortina Presidio ASIC Platform"
> +	select ARM64
> +
>  endchoice
>  
>  config ARCH_SUPPORT_TFABOOT
> @@ -1782,6 +1786,7 @@ source "board/Marvell/gplugd/Kconfig"
>  source "board/armadeus/apf27/Kconfig"
>  source "board/armltd/vexpress/Kconfig"
>  source "board/armltd/vexpress64/Kconfig"
> +source "board/cortina/presidio-asic/Kconfig"
>  source "board/broadcom/bcm23550_w1d/Kconfig"
>  source "board/broadcom/bcm28155_ap/Kconfig"
>  source "board/broadcom/bcm963158/Kconfig"
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 0127a91..81db1e6 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -849,6 +849,8 @@ dtb-$(CONFIG_TARGET_VEXPRESS_CA15_TC2) += vexpress-v2p-ca15_a7.dtb
>  
>  dtb-$(CONFIG_TARGET_DURIAN) += phytium-durian.dtb
>  
> +dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb
> +
>  targets += $(dtb-y)
>  
>  # Add any required device tree compiler flags here
> diff --git a/arch/arm/dts/ca-presidio-engboard.dts b/arch/arm/dts/ca-presidio-engboard.dts
> new file mode 100644
> index 0000000..ef371b0
> --- /dev/null
> +++ b/arch/arm/dts/ca-presidio-engboard.dts
> @@ -0,0 +1,69 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2020, Cortina Access Inc.
> + */
> +
> +/dts-v1/;
> +
> +/ {
> +   #address-cells = <2>;
> +   #size-cells = <1>;
> +
> +	mmc0: mmc at f4400000 {
> +		compatible = "snps,dw-cortina";
> +		reg = <0x0 0xf4400000 0x1000>;
> +		bus-width = <4>;
> +		io_ds = <0x77>;
> +		fifo-mode;
> +		sd_dll_ctrl = <0xf43200e8>;
> +		io_drv_ctrl = <0xf432004c>;
> +	};
> +
> +	gpio0: gpio-controller at 0xf4329280  {
> +		compatible = "cortina,ca-gpio";
> +		reg = <0x0 0xf4329280 0x24>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		status = "okay";
> +	};
> +	gpio1: gpio-controller at 0xf43292a4  {
> +		compatible = "cortina,ca-gpio";
> +		reg = <0x0 0xf43292a4 0x24>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		status = "disabled";
> +	};
> +
> +	watchdog: watchdog at 0xf432901c {
> +		compatible = "cortina,ca-wdt";
> +		reg = <0x0 0xf432901c 0x34>,
> +		      <0x0 0xf4320020 0x04>;
> +		status = "okay";
> +	};
> +
> +	uart0: serial at 0xf4329148  {
> +		u-boot,dm-pre-reloc;
> +		compatible = "cortina,ca-uart";
> +		reg = <0x0 0xf4329148 0x30>;
> +		status = "okay";
> +	};
> +
> +	i2c: i2c at f4329120 {
> +		compatible = "cortina,ca-i2c";
> +		reg = <0x0 0xf4329120 0x28>;
> +		clock-frequency = <400000>;
> +	};
> +
> +	sflash: sflash-controller at f4324000 {
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		compatible = "cortina,ca-sflash";
> +		reg = <0x0 0xf4324000 0x50>;
> +		reg-names = "sflash-regs";
> +		flash at 0 {
> +			compatible = "jedec,spi-nor";
> +			spi-rx-bus-width = <1>;
> +			spi-max-frequency = <108000000>;
> +			};

closing bracket is incorrectly indented

> +	};
> +};
> diff --git a/board/cortina/common/armv8/ca7774_regs.h b/board/cortina/common/armv8/ca7774_regs.h
> new file mode 100644
> index 0000000..d997155
> --- /dev/null
> +++ b/board/cortina/common/armv8/ca7774_regs.h
> @@ -0,0 +1,18 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2015-2020, Cortina-Access Incorporation.
> + */
> +
> +#ifndef _CA7774_H_
> +#define _CA7774_H_
> +
> +#define CA_PERIPH_BASE                  0xE0000000UL
> +#define CA_PERIPH_SIZE                  0x20000000UL
> +#define CA_GLOBAL_BASE                  0xf4320000
> +#define CA_GLOBAL_JTAG_ID               0xf4320000
> +#define CA_GLOBAL_BLOCK_RESET           0xf4320004
> +#define CA_GLOBAL_BLOCK_RESET_RESET_DMA BIT(16)
> +#define CA_DMA_SEC_SSP_BAUDRATE_CTRL    0xf7001b94
> +#define CA_DMA_SEC_SSP_ID               0xf7001b80
> +
> +#endif /* _CA7774_H_ */
> diff --git a/board/cortina/presidio-asic/Kconfig b/board/cortina/presidio-asic/Kconfig
> new file mode 100644
> index 0000000..8b3f3fd
> --- /dev/null
> +++ b/board/cortina/presidio-asic/Kconfig
> @@ -0,0 +1,20 @@
> +if TARGET_PRESIDIO_ASIC
> +config BIT64
> +	bool
> +	default y
> +
> +config CA77XX
> +	bool
> +	default y
> +
> +config SYS_BOARD
> +	default "presidio-asic"
> +
> +config SYS_VENDOR
> +	default "cortina"
> +
> +config SYS_CONFIG_NAME
> +	default "presidio_asic"
> +
> +source "board/cortina/common/Kconfig"
> +endif
> diff --git a/board/cortina/presidio-asic/MAINTAINERS b/board/cortina/presidio-asic/MAINTAINERS
> new file mode 100644
> index 0000000..9db17bd
> --- /dev/null
> +++ b/board/cortina/presidio-asic/MAINTAINERS
> @@ -0,0 +1,6 @@
> +Cortina Presidio ASIC G3 Engineering BOARD
> +M:	Alex Nemirovsky <alex.nemirovsky at cortina-access.com>
> +S:	Supported
> +F:	board/cortina/presidio-asic/
> +F:	include/configs/presidio_asic.h
> +F:	configs/cortina_presidio-asic*defconfig
> diff --git a/board/cortina/presidio-asic/Makefile b/board/cortina/presidio-asic/Makefile
> new file mode 100644
> index 0000000..33f8e7c
> --- /dev/null
> +++ b/board/cortina/presidio-asic/Makefile
> @@ -0,0 +1,8 @@
> +# SPDX-License-Identifier:	GPL-2.0+
> +#
> +# (C) Copyright 2020 Cortina-Access.Inc.
> +#
> +#
> +
> +obj-y	:= presidio.o
> +obj-y	+= ../common/armv8/lowlevel_init.o
> diff --git a/board/cortina/presidio-asic/presidio.c b/board/cortina/presidio-asic/presidio.c
> new file mode 100644
> index 0000000..1bebe28
> --- /dev/null
> +++ b/board/cortina/presidio-asic/presidio.c
> @@ -0,0 +1,126 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2020 - Cortina Access Inc.
> + *
> + */
> +#include <common.h>
> +#include <malloc.h>
> +#include <errno.h>
> +#include <netdev.h>
> +#include <asm/io.h>
> +#include <linux/compiler.h>
> +#include <configs/presidio_asic.h>
> +#include <linux/psci.h>
> +#include <asm/psci.h>
> +#include <cpu_func.h>
> +#include <asm/armv8/mmu.h>
> +#include "../common/armv8/ca7774_regs.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int print_cpuinfo(void)
> +{
> +	printf("CPU:   Cortina Presidio G3\n");
> +	return 0;
> +}
> +
> +static struct mm_region presidio_mem_map[] = {
> +	{
> +	.virt = DDR_BASE,
> +	.phys = DDR_BASE,
> +	.size = PHYS_SDRAM_1_SIZE,
> +	.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
> +		 PTE_BLOCK_OUTER_SHARE
> +	},
> +	{
> +	.virt = CA_PERIPH_BASE,
> +	.phys = CA_PERIPH_BASE,
> +	.size = CA_PERIPH_SIZE,
> +	.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
> +		 PTE_BLOCK_NON_SHARE
> +	},
> +	{
> +	/* List terminator */
> +	0,
> +	}
> +};
> +
> +struct mm_region *mem_map = presidio_mem_map;
> +
> +static noinline int invoke_psci_fn_smc(u64 function_id, u64 arg0, u64 arg1,
> +				       u64 arg2)
> +{
> +	asm volatile("mov x0, %0\n"
> +		    "mov x1, %1\n"
> +		    "mov x2, %2\n"
> +		    "mov x3, %3\n"
> +		    "smc	#0\n"
> +		    : "+r" (function_id)
> +		    : "r" (arg0), "r" (arg1), "r" (arg2)
> +		    );
> +
> +	return function_id;
> +}
> +
> +int board_early_init_r(void)
> +{
> +	dcache_disable();
> +	return 0;
> +}
> +
> +int board_init(void)
> +{
> +	unsigned int reg_data, jtag_id;
> +
> +	/* Enable timer */
> +	writel(1, CONFIG_SYS_TIMER_BASE);
> +
> +	/* Enable snoop in CCI400 slave port#4 */
> +	writel(3, 0xF5595000);
> +
> +	jtag_id = readl(CA_GLOBAL_JTAG_ID);
> +
> +	/* If this is HGU variant then do not use
> +	 * the Saturn daughter card ref. clk
> +	 */
> +	if (jtag_id == 0x1010D8F3) {
> +		reg_data = readl(0xF3100064);
> +		/* change multifunc. REF CLK pin to
> +		 * a simple GPIO pin
> +		 */
> +		reg_data |= (1 << 1);
> +		writel(reg_data, 0xf3100064);
> +	}
> +
> +	return 0;
> +}
> +
> +int dram_init(void)
> +{
> +	unsigned int ddr_size;
> +
> +	ddr_size = readl(0x111100c);
> +	gd->ram_size = ddr_size * 0x100000;
> +	return 0;
> +}
> +
> +void reset_cpu(ulong addr)
> +{
> +	invoke_psci_fn_smc(PSCI_0_2_FN_SYSTEM_RESET, 0, 0, 0);
> +}
> +
> +#ifdef CONFIG_LAST_STAGE_INIT
> +int last_stage_init(void)
> +{
> +	u32 val;
> +
> +	val = readl(CA_GLOBAL_BLOCK_RESET);
> +	val &= ~CA_GLOBAL_BLOCK_RESET_RESET_DMA;
> +	writel(val, CA_GLOBAL_BLOCK_RESET);
> +
> +	/* reduce output pclk ~3.7Hz to save power consumption */
> +	writel(0x000000FF, CA_DMA_SEC_SSP_BAUDRATE_CTRL);
> +
> +	return 0;
> +}
> +#endif
> diff --git a/configs/cortina_presidio-asic-base_defconfig b/configs/cortina_presidio-asic-base_defconfig
> new file mode 100644
> index 0000000..45b911c
> --- /dev/null
> +++ b/configs/cortina_presidio-asic-base_defconfig
> @@ -0,0 +1,45 @@
> +# Cortina-Access Ltd. Presidio ASIC Board

the defconfig file must not created manually, try this:

make savedefconfig
cp defconfig configs/cortina_presidio-asic-base_defconfig

> +CONFIG_CORTINA_PLATFORM=y
> +CONFIG_ARM=y
> +CONFIG_SYS_ARCH_TIMER=n
> +CONFIG_TARGET_PRESIDIO_ASIC=y
> +CONFIG_SHOW_BOOT_PROGRESS=y
> +CONFIG_BOARD_EARLY_INIT_R=y
> +CONFIG_ENV_OFFSET=0x400000
> +CONFIG_ENV_SIZE=0x20000
> +CONFIG_SYS_TEXT_BASE=0x04000000
> +CONFIG_BOOTDELAY=3
> +CONFIG_SYS_PROMPT="G3#"
> +CONFIG_NR_DRAM_BANKS=1
> +CONFIG_CONS_INDEX=0
> +CONFIG_IDENT_STRING="Presidio-SoC"
> +CONFIG_BOOTP_VCI_STRING="U-boot.armv8.presidio"
> +CONFIG_OF_LIBFDT=y
> +
> +CONFIG_MENU=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIMER=y
> +CONFIG_CMD_SMC=y
> +
> +CONFIG_DM=y
> +CONFIG_CORTINA_UART=y
> +CONFIG_REQUIRE_SERIAL_CONSOLE=y
> +CONFIG_DM_SERIAL=y
> +
> +CONFIG_DM_GPIO=y
> +CONFIG_CORTINA_GPIO=y
> +
> +CONFIG_WATCHDOG=y
> +CONFIG_WATCHDOG_TIMEOUT_MSECS=60000
> +CONFIG_WDT=y
> +CONFIG_WDT_CORTINA=y
> +CONFIG_CMD_WDT=y
> +
> +CONFIG_OF_CONTROL=y
> +CONFIG_OF_LIVE=y
> +CONFIG_OF_SEPARATE=y
> +CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard"
> +
> +CONFIG_MMC=n
> +CONFIG_NET=n
> +CONFIG_NETDEVICES=n
> diff --git a/include/configs/presidio_asic.h b/include/configs/presidio_asic.h
> new file mode 100644
> index 0000000..d4f7888
> --- /dev/null
> +++ b/include/configs/presidio_asic.h
> @@ -0,0 +1,123 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2020 Cortina Access Inc.
> + *
> + * Configuration for Cortina-Access Presidio board.
> + */
> +
> +#ifndef __PRESIDIO_ASIC_H
> +#define __PRESIDIO_ASIC_H
> +
> +#define CONFIG_BIT64	1
> +
> +//#include <generated/autoconf.h>

remove dead code

> +
> +#define CA_REG_READ(addr)              readl((u64)addr)
> +#define CA_REG_WRITE(value, addr)      writel(value, (u64)addr)

don't use custom I/O accessors

> +
> +#define CONFIG_CA77XX	1

new config options should be added in Kconfig

> +
> +#define CONFIG_REMAKE_ELF
> +
> +#define CONFIG_GICV2
> +
> +#define CONFIG_SUPPORT_RAW_INITRD
> +#define CONFIG_ARMV8_MULTIENTRY
> +
> +/* SMP jump address in DRAM */
> +#define CPU_RELEASE_ADDR		0x0740fff8
> +
> +#define CONFIG_SYS_INIT_SP_ADDR		0x00100000
> +#define CONFIG_SYS_BOOTM_LEN		0x00c00000
> +
> +/* Generic Timer Definitions */
> +#define COUNTER_FREQUENCY		25000000
> +#define CONFIG_SYS_TIMER_RATE COUNTER_FREQUENCY
> +#define CONFIG_SYS_TIMER_COUNTER 0xf4321008
> +
> +/* Generic Interrupt Controller Definitions */
> +#define GICD_BASE			0xf7011000
> +#define GICC_BASE			0xf7012000

don't put register addresses in the config file. Those should come from
device-tree anyway. The config file should only set the legacy config
options which aren't yet migrated to Kconfig. If you need that in
low-level code or so, put the defines there or create a small header file

> +
> +#define CONFIG_SYS_MEMTEST_SCRATCH	0x00100000
> +#define CONFIG_SYS_MEMTEST_START	0x05000000
> +#define CONFIG_SYS_MEMTEST_END		0x0D000000
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (8 << 20))
> +
> +#define CONFIG_SYS_TIMER_BASE		0xf4321000
> +
> +/* Use external clock source */
> +#define PRESIDIO_APB_CLK		125000000
> +#define CORTINA_PER_IO_FREQ		PRESIDIO_APB_CLK
> +
> +/* Cortina Serial Configuration */
> +#define CORTINA_UART_CLOCK		(PRESIDIO_APB_CLK)
> +#define CORTINA_SERIAL_PORTS		{(void *)CONFIG_SYS_SERIAL0, \
> +					 (void *)CONFIG_SYS_SERIAL1}
> +
> +#define CONFIG_BAUDRATE			115200
> +#define CONFIG_SYS_SERIAL0		PER_UART0_CFG
> +#define CONFIG_SYS_SERIAL1		PER_UART1_CFG
> +
> +/* BLOCK Reset Definitions */
> +#define RESET_OTPROM			BIT(29)
> +#define RESET_SD			BIT(28)
> +#define RESET_EAXI			BIT(27)
> +#define RESET_FBM			BIT(26)
> +#define RESET_LDMA			BIT(25)
> +#define RESET_RCRYPTO			BIT(24)
> +#define RESET_SADB			BIT(22)
> +#define RESET_RCPU1			BIT(21)
> +#define RESET_RCPU0			BIT(20)
> +#define RESET_PE1			BIT(19)
> +#define RESET_PE0			BIT(18)
> +#define RESET_RTC			BIT(17)
> +#define RESET_DMA			BIT(16)
> +#define RESET_PER			BIT(15)
> +#define RESET_FLASH			BIT(14)
> +#define RESET_GIC400			BIT(10)
> +#define RESET_SATA			BIT(9)
> +#define RESET_PCIE2			BIT(8)
> +#define RESET_PCIE1			BIT(7)
> +#define RESET_PCIE0			BIT(6)
> +#define RESET_TQM			BIT(5)
> +#define RESET_SDRAM			BIT(4)
> +#define RESET_L3FE			BIT(3)
> +#define RESET_L2TM			BIT(2)
> +#define RESET_L2FE			BIT(1)
> +#define RESET_NI			BIT(0)
> +
> +/* BOOTP options */
> +#define CONFIG_BOOTP_BOOTFILESIZE
> +
> +/* Miscellaneous configurable options */
> +#define DDR_BASE			0x00000000
> +#define CONFIG_SYS_LOAD_ADDR		(DDR_BASE + 0x10000000)
> +#define CONFIG_LAST_STAGE_INIT
> +
> +/* Physical Memory Map */
> +
> +/* SDRAM Bank #1 */
> +#define PHYS_SDRAM_1			DDR_BASE
> +#define PHYS_SDRAM_1_SIZE		0x80000000 /* 2GB */
> +#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
> +
> +/* Initial environment variables */
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS	"silent=y\0"
> +#define CONFIG_BOOTARGS			"earlycon=serial,0xf4329148 console=ttyS0,115200 root=/dev/ram0"
> +
> +/* Monitor Command Prompt */
> +
> +/* Console I/O Buffer Size */
> +#define CONFIG_SYS_CBSIZE		256
> +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> +					sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
> +
> +/* max command args */
> +#define CONFIG_SYS_MAXARGS		64
> +
> +#endif /* __PRESIDIO_ASIC_H */
> 

-- 
- Daniel


More information about the U-Boot mailing list