[PATCH] mx6sxsabresd: Convert to DM_ETH

[Pedro Jardim]

This fixes the following warning

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Pedro Jardim <jardim.c.pedro at gmail.com>
---
 board/freescale/mx6sxsabresd/mx6sxsabresd.c | 27 +-------------------
 configs/mx6sxsabresd_defconfig              |  5 ++++
 include/configs/mx6sxsabresd.h              | 11 ---------
 3 files changed, 6 insertions(+), 36 deletions(-)

diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 9fff8ffc4c..e2a88cc8e0 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -23,7 +23,6 @@
 #include <mmc.h>
 #include <i2c.h>
 #include <miiphy.h>
-#include <netdev.h>
 #include <power/pmic.h>
 #include <power/pfuze100_pmic.h>
 #include "../common/pfuze.h"
@@ -69,22 +68,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 static iomux_v3_cfg_t const wdog_b_pad = {
 	MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL),
 };
-static iomux_v3_cfg_t const fec1_pads[] = {
-	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RD2__ENET1_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RD3__ENET1_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RXC__ENET1_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_TD2__ENET1_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_TD3__ENET1_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
 
 static iomux_v3_cfg_t const peri_3v3_pads[] = {
 	MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL),
@@ -139,14 +122,6 @@ static int setup_fec(void)
 	return 0;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-	setup_fec();
-
-	return cpu_eth_init(bis);
-}
-
 int power_init_board(void)
 {
 	struct udevice *dev;
 
@@ -297,6 +271,7 @@ int board_init(void)
 #ifdef CONFIG_VIDEO_MXS
 	setup_lcd();
 #endif
+	setup_fec();
 
 	return 0;
 }
diff --git a/configs/mx6sxsabresd_defconfig b/configs/mx6sxsabresd_defconfig
index 8ffc6d1035..801c9b8003 100644
--- a/configs/mx6sxsabresd_defconfig
+++ b/configs/mx6sxsabresd_defconfig
@@ -68,3 +68,8 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
 CONFIG_VIDEO=y
+CONFIG_FEC_MXC=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_RGMII=y
diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h
index 55aace1c6e..498795d3c4 100644
--- a/include/configs/mx6sxsabresd.h
+++ b/include/configs/mx6sxsabresd.h
@@ -148,17 +148,6 @@
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_SPEED		  100000
 
-/* Network */
-#define CONFIG_FEC_MXC
-
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR          0x1
-
-#define CONFIG_FEC_XCV_TYPE             RGMII
-#define CONFIG_ETHPRIME                 "FEC"
-
-#define CONFIG_PHY_ATHEROS
-
 #ifdef CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
-- 
2.17.1