[PATCH 108/108] x86: coral: Update config and device tree for ACPI

Simon Glass sjg at chromium.org
Mon Jan 27 06:06:55 CET 2020


Enable new features and provide require device-tree config so that U-Boot
produces the correct ACPI tables on Coral.

Signed-off-by: Simon Glass <sjg at chromium.org>
---

 arch/x86/dts/chromebook_coral.dts  | 193 ++++++++++++++++++++++++++++-
 configs/chromebook_coral_defconfig |  14 ++-
 2 files changed, 199 insertions(+), 8 deletions(-)

diff --git a/arch/x86/dts/chromebook_coral.dts b/arch/x86/dts/chromebook_coral.dts
index 3c6f14310f..1d16975f5c 100644
--- a/arch/x86/dts/chromebook_coral.dts
+++ b/arch/x86/dts/chromebook_coral.dts
@@ -16,8 +16,12 @@
 #endif
 
 #include <dt-bindings/clock/intel-clock.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/x86-irq.h>
+#include <asm/e820.h>
 #include <asm/intel_pinctrl_defs.h>
 #include <asm/arch-apollolake/cpu.h>
+#include <asm/arch-apollolake/gpe.h>
 #include <asm/arch-apollolake/gpio.h>
 #include <asm/arch-apollolake/iomap.h>
 #include <asm/arch-apollolake/pm.h>
@@ -38,6 +42,14 @@
 		i2c5 = &i2c_5;
 		i2c6 = &i2c_6;
 		i2c7 = &i2c_7;
+		mmc1 = &sdmmc;
+	};
+
+	board: board {
+		compatible = "google,coral";
+		recovery-gpios = <&gpio_nw (-1) GPIO_ACTIVE_LOW>;
+		write-protect-gpios = <&gpio_nw GPIO_75 GPIO_ACTIVE_HIGH>;
+		phase-enforce-gpios = <&gpio_n GPIO_10 GPIO_ACTIVE_HIGH>;
 	};
 
 	config {
@@ -46,6 +58,15 @@
 
 	chosen {
 		stdout-path = &serial;
+		e820-entries = /bits/ 64 <
+			IOMAP_P2SB_BAR IOMAP_P2SB_SIZE E820_RESERVED
+			MCH_BASE_ADDRESS     MCH_SIZE  E820_RESERVED>;
+		u-boot,acpi-ssdt-order = <&cpu_0
+			&i2c_0 &i2c_1 &i2c_2 &i2c_3 &i2c_4 &i2c_5
+			&sdmmc &maxim_codec &wifi &da_codec &tpm
+			&elan_touchscreen &raydium_touchscreen
+			&elan_touchpad &synaptics_touchpad &wacom_digitizer>;
+		u-boot,acpi-dsdt-order = <&board &lpc>;
 	};
 
 	clk: clock {
@@ -58,7 +79,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu at 0 {
+		cpu_0: cpu at 0 {
 			u-boot,dm-pre-reloc;
 			device_type = "cpu";
 			compatible = "intel,apl-cpu";
@@ -133,21 +154,29 @@
 			compatible = "intel,apl-punit";
 		};
 
+		gma at 2,0 {
+			reg = <0x00001000 0 0 0 0>;
+			compatible = "intel,gma";
+		};
+
 		p2sb: p2sb at d,0 {
 			u-boot,dm-pre-reloc;
 			reg = <0x02006810 0 0 0 0>;
 			compatible = "intel,apl-p2sb";
 			early-regs = <IOMAP_P2SB_BAR 0x100000>;
+			pci,no-autoconfig;
 
 			n {
 				compatible = "intel,apl-pinctrl";
 				u-boot,dm-pre-reloc;
 				intel,p2sb-port-id = <PID_GPIO_N>;
+				acpi,path = "\\_SB.GPO0";
 				gpio_n: gpio-n {
 					compatible = "intel,gpio";
 					u-boot,dm-pre-reloc;
 					gpio-controller;
 					#gpio-cells = <2>;
+					linux-name = "INT3452:00";
 				};
 			};
 
@@ -156,11 +185,13 @@
 				compatible = "intel,apl-pinctrl";
 				intel,p2sb-port-id = <PID_GPIO_NW>;
 				#gpio-cells = <2>;
+				acpi,path = "\\_SB.GPO1";
 				gpio_nw: gpio-nw {
 					compatible = "intel,gpio";
 					u-boot,dm-pre-reloc;
 					gpio-controller;
 					#gpio-cells = <2>;
+					linux-name = "INT3452:01";
 				};
 			};
 
@@ -169,11 +200,13 @@
 				compatible = "intel,apl-pinctrl";
 				intel,p2sb-port-id = <PID_GPIO_W>;
 				#gpio-cells = <2>;
+				acpi,path = "\\_SB.GPO2";
 				gpio_w: gpio-w {
 					compatible = "intel,gpio";
 					u-boot,dm-pre-reloc;
 					gpio-controller;
 					#gpio-cells = <2>;
+					linux-name = "INT3452:02";
 				};
 			};
 
@@ -182,11 +215,13 @@
 				compatible = "intel,apl-pinctrl";
 				intel,p2sb-port-id = <PID_GPIO_SW>;
 				#gpio-cells = <2>;
+				acpi,path = "\\_SB.GPO3";
 				gpio_sw: gpio-sw {
 					compatible = "intel,gpio";
 					u-boot,dm-pre-reloc;
 					gpio-controller;
 					#gpio-cells = <2>;
+					linux-name = "INT3452:03";
 				};
 			};
 
@@ -235,6 +270,23 @@
 			gpe0-en = <0x30>;
 		};
 
+		audio at e,0 {
+			reg = <0x7000 0 0 0 0>;
+			compatible = "simple-bus";
+			acpi,name = "HDAS";
+			i2s {
+				compatible = "fred";
+			};
+			maxim_codec: maxim-codec {
+				compatible = "maxim,max98357a";
+				acpi,desc = "Maxim Integrated 98357A Amplifier";
+				sdmode-gpios = <&gpio_n GPIO_76 GPIO_ACTIVE_HIGH>;
+				sdmode-delay = <5>;
+				acpi,name = "MAXM";
+				acpi,hid = "MX98357A";
+			};
+		};
+
 		spi: fast-spi at d,2 {
 			u-boot,dm-pre-reloc;
 			reg = <0x02006a10 0 0 0 0>;
@@ -264,19 +316,60 @@
 			};
 		};
 
+		/* WiFi */
+		pcie-a0 at 14,0 {
+			reg = <0x0000a000 0 0 0 0>;
+			acpi,name = "RP01";
+			wifi: wifi {
+				compatible = "intel,generic-wifi";
+				acpi,desc = "Intel WiFi";
+				acpi,name = "WF00";
+				acpi,wake = <GPE0_DW3_00>;
+				interrupts-extended = <&acpi_gpe 0x3c 0>;
+			};
+		};
+
 		i2c_0: i2c2 at 16,0 {
 			compatible = "intel,apl-i2c";
 			reg = <0x0200b010 0 0 0 0>;
 			clocks = <&clk CLK_I2C>;
 			i2c-scl-rising-time-ns = <104>;
 			i2c-scl-falling-time-ns = <52>;
+			clock-frequency = <400000>;
+			i2c,speeds = <100000 400000 1000000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			da_codec: da-codec {
+				reg = <0x1a>;
+				compatible = "dlg,da7219";
+				interrupts-extended = <&acpi_gpe GPIO_116_IRQ
+					(IRQ_TYPE_LEVEL_LOW | X86_IRQ_TYPE_SHARED)>;
+				acpi,name = "DLG7";
+				acpi,desc = "Dialog Semiconductor DA7219 Audio Codec";
+				dlg,btn-cfg = <50>;
+				dlg,mic-det-thr = <500>;
+				dlg,jack-ins-deb = <20>;
+				dlg,jack-det-rate = "32ms_64ms";
+				dlg,jack-rem-deb = <1>;
+				dlg,a-d-btn-thr = <0xa>;
+				dlg,d-b-btn-thr = <0x16>;
+				dlg,b-c-btn-thr = <0x21>;
+				dlg,c-mic-btn-thr = <0x3e>;
+				dlg,btn-avg = <4>;
+				dlg,adc-1bit-rpt = <1>;
+				dlg,micbias-lvl = <2600>;
+				dlg,mic-amp-in-sel = "diff";
+			};
 		};
 
 		i2c_1: i2c2 at 16,1 {
 			compatible = "intel,apl-i2c";
 			reg = <0x0200b110 0 0 0 0>;
 			clocks = <&clk CLK_I2C>;
-			status = "disabled";
+			clock-frequency = <400000>;
+			i2c,speeds = <100000 400000 1000000 3400000>;
+			i2c-scl-rising-time-ns = <52>;
+			i2c-scl-falling-time-ns = <52>;
 		};
 
 		i2c_2: i2c2 at 16,2 {
@@ -285,41 +378,119 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clock-frequency = <400000>;
+			i2c,speeds = <100000 400000 1000000>;
 			clocks = <&clk CLK_I2C>;
 			i2c-scl-rising-time-ns = <57>;
 			i2c-scl-falling-time-ns = <28>;
-			tpm at 50 {
+			tpm: tpm at 50 {
 				reg = <0x50>;
 				compatible = "google,cr50";
 				u-boot,i2c-offset-len = <0>;
 				ready-gpios = <&gpio_n 28 GPIO_ACTIVE_LOW>;
-				interrupts-extended = <&acpi_gpe 0x3c 0>;
+				interrupts-extended = <&acpi_gpe GPIO_28_IRQ
+					 IRQ_TYPE_EDGE_FALLING>;
+				acpi,hid = "GOOG0005";
+				acpi,desc = "I2C TPM";
+				acpi,name = "TPMI";
 			};
 		};
 
 		i2c_3: i2c2 at 16,3 {
 			compatible = "intel,apl-i2c";
 			reg = <0x0200b110 0 0 0 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			clocks = <&clk CLK_I2C>;
 			i2c-scl-rising-time-ns = <76>;
 			i2c-scl-falling-time-ns = <164>;
+			clock-frequency = <400000>;
+			i2c,speeds = <100000 400000>;
+			elan_touchscreen: elan-touchscreen at 10 {
+				compatible = "i2c-chip";
+				reg = <0x10>;
+				acpi,hid = "ELAN0001";
+				acpi,desc = "ELAN Touchscreen";
+				interrupts-extended = <&acpi_gpe GPIO_21_IRQ
+					IRQ_TYPE_EDGE_FALLING>;
+				acpi,probed;
+				reset-gpios = <&gpio_n GPIO_36 GPIO_ACTIVE_HIGH>;
+				reset-delay-ms = <20>;
+				enable-gpios = <&gpio_n GPIO_152 GPIO_ACTIVE_HIGH>;
+				enable-delay-ms = <1>;
+				acpi,has-power-resource;
+			};
+
+			raydium_touchscreen: raydium-touchscreen at 39 {
+				compatible = "i2c-chip";
+				reg = <0x39>;
+				acpi,hid = "RAYD0001";
+				acpi,desc = "Raydium Touchscreen";
+				interrupts-extended = <&acpi_gpe GPIO_21_IRQ
+					IRQ_TYPE_EDGE_FALLING>;
+				acpi,probed;
+				reset-gpios = <&gpio_n GPIO_36 GPIO_ACTIVE_HIGH>;
+				reset-delay-ms = <1>;
+				enable-gpios = <&gpio_n GPIO_152 GPIO_ACTIVE_HIGH>;
+				enable-delay-ms = <50>;
+				acpi,has-power-resource;
+			};
 		};
 
 		i2c_4: i2c2 at 17,0 {
 			compatible = "intel,apl-i2c";
 			reg = <0x0200b110 0 0 0 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			clocks = <&clk CLK_I2C>;
 			i2c-sda-hold-time-ns = <350>;
 			i2c-scl-rising-time-ns = <114>;
 			i2c-scl-falling-time-ns = <164>;
+			clock-frequency = <400000>;
+			i2c,speeds = <100000 400000>;
+			elan_touchpad: elan-touchpad at 15 {
+				compatible = "i2c-chip";
+				reg = <0x15>;
+				acpi,hid = "ELAN0000";
+				acpi,desc = "ELAN Touchpad";
+				interrupts-extended = <&acpi_gpe GPIO_18_IRQ
+					 IRQ_TYPE_EDGE_FALLING>;
+				acpi,wake = <GPE0_DW1_15>;
+				acpi,probed;
+			};
+			synaptics_touchpad: synaptics-touchpad at 2c {
+				compatible = "i2c-chip";
+				reg = <0x2c>;
+				acpi,hid = "PNP0C50";
+				acpi,cid = "PNP0C50";
+				acpi,desc = "Synaptics Touchpad";
+				interrupts-extended = <&acpi_gpe GPIO_18_IRQ
+					 IRQ_TYPE_EDGE_FALLING>;
+				acpi,wake = <GPE0_DW1_15>;
+				acpi,probed;
+				acpi,hid-desc-reg-offset = <0x20>;
+			};
 		};
 
 		i2c_5: i2c2 at 17,1 {
 			compatible = "intel,apl-i2c";
 			reg = <0x0200b110 0 0 0 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			clocks = <&clk CLK_I2C>;
 			i2c-scl-rising-time-ns = <76>;
 			i2c-scl-falling-time-ns = <164>;
+			clock-frequency = <400000>;
+			i2c,speeds = <100000 400000 1000000>;
+			wacom_digitizer: wacom-digitizer at 9 {
+				compatible = "i2c-chip";
+				reg = <0x9>;
+				acpi,hid = "WCOM50C1";
+				acpi,cid = "PNP0C50";
+				acpi,desc = "WCOM Digitizer";
+				interrupts-extended = <&acpi_gpe GPIO_13_IRQ
+					(IRQ_TYPE_LEVEL_LOW | X86_IRQ_TYPE_SHARED)>;
+				acpi,hid-desc-reg-offset = <0x1>;
+			};
 		};
 
 		i2c_6: i2c2 at 17,2 {
@@ -344,6 +515,15 @@
 			reg-shift = <2>;
 			clock-frequency = <1843200>;
 			current-speed = <115200>;
+			acpi,name = "URT3";
+			pci,no-autoconfig;
+		};
+
+		sdmmc: sdmmc at 1b,0 {
+			reg = <0x0000d800 0 0 0 0>;
+			compatible = "intel,apl-sd";
+			cd-gpios = <&gpio_n GPIO_177 GPIO_ACTIVE_LOW>;
+			acpi,name = "SDCD";
 		};
 
 		pch: pch at 1f,0 {
@@ -353,7 +533,7 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			lpc {
+			lpc: lpc {
 				compatible = "intel,apl-lpc";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -505,6 +685,9 @@
 	/* GPIO for SD card detect */
 	sdcard-cd-gpio = <GPIO_177>;
 
+	 prt0-gpio = <GPIO_122>;
+	 sdcard-cd-gpio = <GPIO_177>;
+
 	/*
 	 * Order is emmc-tx-data-cntl1, emmc-tx-data-cntl2,
 	 * emmc-rx-cmd-data-cntl1, emmc-rx-cmd-data-cntl2
diff --git a/configs/chromebook_coral_defconfig b/configs/chromebook_coral_defconfig
index 0999fb57c6..131c37c798 100644
--- a/configs/chromebook_coral_defconfig
+++ b/configs/chromebook_coral_defconfig
@@ -1,6 +1,7 @@
 CONFIG_X86=y
 CONFIG_SYS_TEXT_BASE=0x1110000
 CONFIG_SYS_MALLOC_F_LEN=0x3d00
+CONFIG_MAX_CPUS=8
 CONFIG_SPL_SYS_MALLOC_F_LEN=0xf000
 CONFIG_NR_DRAM_BANKS=8
 CONFIG_BOOTSTAGE_STASH_ADDR=0xfef00000
@@ -11,9 +12,11 @@ CONFIG_VENDOR_GOOGLE=y
 CONFIG_TARGET_CHROMEBOOK_CORAL=y
 CONFIG_DEBUG_UART=y
 CONFIG_FSP_VERSION2=y
+CONFIG_GENERATE_PIRQ_TABLE=y
+CONFIG_GENERATE_ACPI_TABLE=y
 CONFIG_HAVE_ACPI_RESUME=y
 CONFIG_INTEL_CAR_CQOS=y
-CONFIG_X86_OFFSET_U_BOOT=0xffe00000
+CONFIG_X86_OFFSET_U_BOOT=0xffd00000
 CONFIG_X86_OFFSET_SPL=0xffe80000
 CONFIG_INTEL_GENERIC_WIFI=y
 CONFIG_SPL_TEXT_BASE=0xfef10000
@@ -24,14 +27,15 @@ CONFIG_BOOTSTAGE_REPORT=y
 CONFIG_SPL_BOOTSTAGE_RECORD_COUNT=10
 CONFIG_BOOTSTAGE_STASH=y
 CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="root=/dev/sdb3 init=/sbin/init rootwait ro earlyprintk console=tty0 console=ttyS0,115200"
+CONFIG_BOOTARGS="nr_cpus=1 console=ttyS2,115200n8 cros_legacy loglevel=9 init=/sbin/init oops=panic panic=-1 root=PARTUUID=35c775e7-3735-d745-93e5-d9e0238f7ed0/PARTNROFF=1 rootwait rw noinitrd vt.global_cursor_default=0 add_efi_memmap boot=local noresume noswap i915.modeset=1 nmi_watchdog=panic,lapic disablevmx=off"
 CONFIG_SYS_CONSOLE_INFO_QUIET=y
 CONFIG_SPL_LOG=y
-CONFIG_LOG_DEFAULT_LEVEL=7
+CONFIG_LOG_DEFAULT_LEVEL=4
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_LAST_STAGE_INIT=y
 CONFIG_BLOBLIST=y
 # CONFIG_TPL_BLOBLIST is not set
+CONFIG_BLOBLIST_SIZE=0x30000
 CONFIG_BLOBLIST_ADDR=0x100000
 CONFIG_HANDOFF=y
 CONFIG_TPL_SYS_MALLOC_SIMPLE=y
@@ -71,8 +75,10 @@ CONFIG_REGMAP=y
 CONFIG_SYSCON=y
 CONFIG_SPL_OF_TRANSLATE=y
 CONFIG_CPU=y
+CONFIG_BOARD=y
 CONFIG_DM_I2C=y
 CONFIG_SYS_I2C_DW=y
+CONFIG_MISC=y
 CONFIG_TPL_MISC=y
 CONFIG_CROS_EC=y
 CONFIG_CROS_EC_LPC=y
@@ -84,7 +90,9 @@ CONFIG_PINCTRL=y
 CONFIG_DEBUG_UART_SHIFT=2
 CONFIG_SYS_NS16550=y
 CONFIG_SOUND=y
+CONFIG_SOUND_DA7219=y
 CONFIG_SOUND_I8254=y
+CONFIG_SOUND_MAX98357A=y
 CONFIG_SOUND_RT5677=y
 CONFIG_SPI=y
 CONFIG_ICH_SPI=y
-- 
2.25.0.341.g760bfbb309-goog



More information about the U-Boot mailing list