[U-Boot, 08/13] board: ge: bx50v3: Enable DM PWM for backlight

[Ian Ray]

From: Robert Beckett <bob.beckett at collabora.com>

Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm

Signed-off-by: Robert Beckett <bob.beckett at collabora.com>
---
 board/ge/bx50v3/bx50v3.c    | 81 +++++++++------------------------------------
 configs/ge_bx50v3_defconfig |  3 ++
 include/configs/ge_bx50v3.h |  2 +-
 3 files changed, 20 insertions(+), 66 deletions(-)

diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
index 4a75c7b..a29fc42 100644
--- a/board/ge/bx50v3/bx50v3.c
+++ b/board/ge/bx50v3/bx50v3.c
@@ -37,6 +37,7 @@
 #include "../common/vpd_reader.h"
 #include "../../../drivers/net/e1000.h"
 #include <pci.h>
+#include <panel.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -124,16 +125,20 @@ int board_phy_config(struct phy_device *phydev)
 }
 
 #if defined(CONFIG_VIDEO_IPUV3)
-static iomux_v3_cfg_t const backlight_pads[] = {
-	/* Power for LVDS Display */
-	MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
-	/* Backlight enable for LVDS display */
-	MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
-	/* backlight PWM brightness control */
-	MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
+static void do_enable_backlight(struct display_info_t const *dev)
+{
+	struct udevice *panel;
+	int ret;
+
+	ret = uclass_get_device(UCLASS_PANEL, 0, &panel);
+	if (ret) {
+		printf("Could not find panel: %d\n", ret);
+		return;
+	}
+
+	panel_set_backlight(panel, 100);
+	panel_enable_backlight(panel);
+}
 
 static void do_enable_hdmi(struct display_info_t const *dev)
 {
@@ -155,7 +160,7 @@ struct display_info_t const displays[] = {{
 	.addr	= -1,
 	.pixfmt	= IPU_PIX_FMT_RGB24,
 	.detect	= detect_lcd,
-	.enable	= NULL,
+	.enable	= do_enable_backlight,
 	.mode	= {
 		.name           = "G121X1-L03",
 		.refresh        = 60,
@@ -314,12 +319,6 @@ static void setup_display_bx50v3(void)
 			IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
 		       (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
 			IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
-
-	/* backlights off until needed */
-	imx_iomux_v3_setup_multiple_pads(backlight_pads,
-					 ARRAY_SIZE(backlight_pads));
-	gpio_request(LVDS_POWER_GP, "lvds_power");
-	gpio_direction_input(LVDS_POWER_GP);
 }
 #endif /* CONFIG_VIDEO_IPUV3 */
 
@@ -476,9 +475,6 @@ int board_init(void)
 		setup_display_b850v3();
 	else
 		setup_display_bx50v3();
-
-	gpio_request(LVDS_BACKLIGHT_GP, "lvds_backlight");
-	gpio_direction_input(LVDS_BACKLIGHT_GP);
 #endif
 
 	/* address of boot parameters */
@@ -590,51 +586,6 @@ int ft_board_setup(void *blob, bd_t *bd)
 }
 #endif
 
-static int do_backlight_enable(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-#if CONFIG_IS_ENABLED(DM_VIDEO)
-	int ret;
-	struct udevice *dev;
-
-#ifdef CONFIG_VIDEO_IPUV3
-	if (!is_b850v3()) {
-		gpio_direction_output(LVDS_POWER_GP, 1);
-
-		/* We need at least 200ms between power on and backlight on
-		 * as per specifications from CHI MEI
-		 */
-		mdelay(250);
-
-		/* enable backlight PWM 1 */
-		pwm_init(0, 0, 0);
-
-		/* duty cycle 5000000ns, period: 5000000ns */
-		pwm_config(0, 5000000, 5000000);
-
-		/* Backlight Power */
-		gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
-
-		pwm_enable(0);
-	}
-#endif
-
-	/* Probe, to find a video device to be used to show a message on
-	 * the vidconsole.
-	 */
-	ret = uclass_get_device(UCLASS_VIDEO, 0, &dev);
-	if (ret)
-		return ret;
-#endif
-
-	return 0;
-}
-
-U_BOOT_CMD(
-       bx50_backlight_enable, 1,      1,      do_backlight_enable,
-       "enable Bx50 backlight",
-       ""
-);
-
 int board_fit_config_name_match(const char *name)
 {
 	if (!vpd.is_read)
diff --git a/configs/ge_bx50v3_defconfig b/configs/ge_bx50v3_defconfig
index f1f7a0d..6e77499 100644
--- a/configs/ge_bx50v3_defconfig
+++ b/configs/ge_bx50v3_defconfig
@@ -30,6 +30,7 @@ CONFIG_CMD_PCI=y
 # CONFIG_CMD_NFS is not set
 CONFIG_CMD_BOOTCOUNT=y
 CONFIG_CMD_CACHE=y
+CONFIG_CMD_CLS=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_EXT4_WRITE=y
@@ -74,9 +75,11 @@ CONFIG_DM_PCI=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_PWM_IMX=y
+CONFIG_DM_PWM=y
 CONFIG_DM_PMIC=y
 CONFIG_DM_PMIC_DA9063=y
 CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_DA9063=y
 CONFIG_DM_RTC=y
 CONFIG_RTC_RX8010SJ=y
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
index b9227fc..46a3c38 100644
--- a/include/configs/ge_bx50v3.h
+++ b/include/configs/ge_bx50v3.h
@@ -105,7 +105,7 @@
 		"setexpr partnum 3 - ${partnum}\0" \
 	"failbootcmd=" \
 		"echo reached failbootcmd; " \
-		"bx50_backlight_enable; " \
+		"cls; " \
 		"setcurs 5 4; " \
 		"lcdputs \"Monitor failed to start. " \
 		"Try again, or contact GE Service for support.\"; " \
-- 
2.10.1