[PATCH v3 10/23] serial: add uart driver for MediaTek MT7620 SoC
Weijie Gao
weijie.gao at mediatek.com
Mon Nov 9 09:25:00 CET 2020
This patch adds uart support for MediaTek MT7620 and earlier SoCs.
The UART used by MT7620 is incompatible with the ns16550a driver.
All registers of this UART have different addresses. A special 16-bit
register for Divisor Latch is used to set the baudrate instead of the
original two 8-bit registers (DLL and DLM).
The driver supports of-platdata which is useful for tiny SPL.
Reviewed-by: Simon Glass <sjg at chromium.org>
Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
---
v3 changes: none
v2 changes: replace non-DM code with of-platdata
---
drivers/serial/Kconfig | 20 +++
drivers/serial/Makefile | 1 +
drivers/serial/serial.c | 2 +
drivers/serial/serial_mt7620.c | 246 +++++++++++++++++++++++++++++++++
4 files changed, 269 insertions(+)
create mode 100644 drivers/serial/serial_mt7620.c
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index b4805a2e4e..44fff8a3cd 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -401,6 +401,16 @@ config DEBUG_UART_MTK
driver will be available until the real driver model serial is
running.
+config DEBUG_UART_MT7620
+ bool "UART driver for MediaTek MT7620 and earlier SoCs"
+ depends on MT7620_SERIAL
+ help
+ Select this to enable a debug UART using the UART driver for
+ MediaTek MT7620 and earlier SoCs.
+ You will need to provide parameters to make this work. The
+ driver will be available until the real driver model serial is
+ running.
+
endchoice
config DEBUG_UART_BASE
@@ -817,6 +827,16 @@ config MTK_SERIAL
The High-speed UART is compatible with the ns16550a UART and have
its own high-speed registers.
+config MT7620_SERIAL
+ bool "UART driver for MediaTek MT7620 and earlier SoCs"
+ depends on DM_SERIAL
+ help
+ Select this to enable UART support for MediaTek MT7620 and earlier
+ SoCs. This driver uses driver model and requires a device tree
+ binding to operate.
+ The UART driver for MediaTek MT7620 and earlier SoCs is *NOT*
+ compatible with the ns16550a UART.
+
config MPC8XX_CONS
bool "Console driver for MPC8XX"
depends on MPC8xx
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 25f7f8d342..0c3810f5d5 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_NULLDEV_SERIAL) += serial_nulldev.o
obj-$(CONFIG_OWL_SERIAL) += serial_owl.o
obj-$(CONFIG_OMAP_SERIAL) += serial_omap.o
obj-$(CONFIG_MTK_SERIAL) += serial_mtk.o
+obj-$(CONFIG_MT7620_SERIAL) += serial_mt7620.o
obj-$(CONFIG_SIFIVE_SERIAL) += serial_sifive.o
obj-$(CONFIG_XEN_SERIAL) += serial_xen.o
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index 355659ba05..1546f41e42 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -127,6 +127,7 @@ serial_initfunc(pl01x_serial_initialize);
serial_initfunc(pxa_serial_initialize);
serial_initfunc(sh_serial_initialize);
serial_initfunc(mtk_serial_initialize);
+serial_initfunc(mt7620_serial_initialize);
/**
* serial_register() - Register serial driver with serial driver core
@@ -181,6 +182,7 @@ int serial_initialize(void)
pxa_serial_initialize();
sh_serial_initialize();
mtk_serial_initialize();
+ mt7620_serial_initialize();
serial_assign(default_serial_console()->name);
diff --git a/drivers/serial/serial_mt7620.c b/drivers/serial/serial_mt7620.c
new file mode 100644
index 0000000000..4f6b5de4cf
--- /dev/null
+++ b/drivers/serial/serial_mt7620.c
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * UART driver for MediaTek MT7620 and earlier SoCs
+ *
+ * Copyright (C) 2020 MediaTek Inc.
+ * Author: Weijie Gao <weijie.gao at mediatek.com>
+ */
+
+#include <clk.h>
+#include <div64.h>
+#include <dm.h>
+#include <errno.h>
+#include <log.h>
+#include <reset.h>
+#include <serial.h>
+#include <watchdog.h>
+#include <asm/io.h>
+#include <asm/types.h>
+#include <asm/addrspace.h>
+#include <dm/device_compat.h>
+#include <linux/err.h>
+
+#if CONFIG_IS_ENABLED(OF_PLATDATA)
+#include <dt-structs.h>
+#endif
+
+struct mt7620_serial_regs {
+ u32 rbr;
+ u32 thr;
+ u32 ier;
+ u32 iir;
+ u32 fcr;
+ u32 lcr;
+ u32 mcr;
+ u32 lsr;
+ u32 msr;
+ u32 scratch;
+ u32 dl;
+ u32 dll;
+ u32 dlm;
+ u32 ifctl;
+};
+
+#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
+
+#define UART_LSR_DR 0x01 /* Data ready */
+#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
+#define UART_LSR_TEMT 0x40 /* Xmitter empty */
+
+#define UART_MCR_DTR 0x01 /* DTR */
+#define UART_MCR_RTS 0x02 /* RTS */
+
+#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
+#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
+#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
+
+#define UART_MCRVAL (UART_MCR_DTR | \
+ UART_MCR_RTS)
+
+/* Clear & enable FIFOs */
+#define UART_FCRVAL (UART_FCR_FIFO_EN | \
+ UART_FCR_RXSR | \
+ UART_FCR_TXSR)
+
+struct mt7620_serial_plat {
+#if CONFIG_IS_ENABLED(OF_PLATDATA)
+ struct dtd_serial_mt7620 dtplat;
+#endif
+
+ struct mt7620_serial_regs __iomem *regs;
+ u32 clock;
+};
+
+static void _mt7620_serial_setbrg(struct mt7620_serial_plat *plat, int baud)
+{
+ u32 quot;
+
+ /* set divisor */
+ quot = DIV_ROUND_CLOSEST(plat->clock, 16 * baud);
+ writel(quot, &plat->regs->dl);
+
+ /* set character length and stop bits */
+ writel(UART_LCR_WLS_8, &plat->regs->lcr);
+}
+
+static int mt7620_serial_setbrg(struct udevice *dev, int baudrate)
+{
+ struct mt7620_serial_plat *plat = dev_get_platdata(dev);
+
+ _mt7620_serial_setbrg(plat, baudrate);
+
+ return 0;
+}
+
+static int mt7620_serial_putc(struct udevice *dev, const char ch)
+{
+ struct mt7620_serial_plat *plat = dev_get_platdata(dev);
+
+ if (!(readl(&plat->regs->lsr) & UART_LSR_THRE))
+ return -EAGAIN;
+
+ writel(ch, &plat->regs->thr);
+
+ if (ch == '\n')
+ WATCHDOG_RESET();
+
+ return 0;
+}
+
+static int mt7620_serial_getc(struct udevice *dev)
+{
+ struct mt7620_serial_plat *plat = dev_get_platdata(dev);
+
+ if (!(readl(&plat->regs->lsr) & UART_LSR_DR))
+ return -EAGAIN;
+
+ return readl(&plat->regs->rbr);
+}
+
+static int mt7620_serial_pending(struct udevice *dev, bool input)
+{
+ struct mt7620_serial_plat *plat = dev_get_platdata(dev);
+
+ if (input)
+ return (readl(&plat->regs->lsr) & UART_LSR_DR) ? 1 : 0;
+
+ return (readl(&plat->regs->lsr) & UART_LSR_THRE) ? 0 : 1;
+}
+
+static int mt7620_serial_probe(struct udevice *dev)
+{
+ struct mt7620_serial_plat *plat = dev_get_platdata(dev);
+
+#if CONFIG_IS_ENABLED(OF_PLATDATA)
+ plat->regs = (void __iomem *)KSEG1ADDR(plat->dtplat.reg[0]);
+ plat->clock = plat->dtplat.clock_frequency;
+#endif
+
+ /* Disable interrupt */
+ writel(0, &plat->regs->ier);
+
+ writel(UART_MCRVAL, &plat->regs->mcr);
+ writel(UART_FCRVAL, &plat->regs->fcr);
+
+ return 0;
+}
+
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+static int mt7620_serial_ofdata_to_platdata(struct udevice *dev)
+{
+ struct mt7620_serial_plat *plat = dev_get_platdata(dev);
+ struct reset_ctl reset_uart;
+ struct clk clk;
+ int err;
+
+ err = reset_get_by_index(dev, 0, &reset_uart);
+ if (!err)
+ reset_deassert(&reset_uart);
+
+ plat->regs = dev_remap_addr_index(dev, 0);
+ if (!plat->regs) {
+ dev_err(dev, "mt7620_serial: unable to map UART registers\n");
+ return -EINVAL;
+ }
+
+ err = clk_get_by_index(dev, 0, &clk);
+ if (!err) {
+ err = clk_get_rate(&clk);
+ if (!IS_ERR_VALUE(err))
+ plat->clock = err;
+ } else if (err != -ENOENT && err != -ENODEV && err != -ENOSYS) {
+ dev_err(dev, "mt7620_serial: failed to get clock\n");
+ return err;
+ }
+
+ if (!plat->clock)
+ plat->clock = dev_read_u32_default(dev, "clock-frequency", 0);
+
+ if (!plat->clock) {
+ dev_err(dev, "mt7620_serial: clock not defined\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct udevice_id mt7620_serial_ids[] = {
+ { .compatible = "mediatek,mt7620-uart" },
+ { }
+};
+#endif
+
+static const struct dm_serial_ops mt7620_serial_ops = {
+ .putc = mt7620_serial_putc,
+ .pending = mt7620_serial_pending,
+ .getc = mt7620_serial_getc,
+ .setbrg = mt7620_serial_setbrg,
+};
+
+U_BOOT_DRIVER(serial_mt7620) = {
+ .name = "serial_mt7620",
+ .id = UCLASS_SERIAL,
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+ .of_match = mt7620_serial_ids,
+ .ofdata_to_platdata = mt7620_serial_ofdata_to_platdata,
+#endif
+ .platdata_auto_alloc_size = sizeof(struct mt7620_serial_plat),
+ .probe = mt7620_serial_probe,
+ .ops = &mt7620_serial_ops,
+ .flags = DM_FLAG_PRE_RELOC,
+};
+
+U_BOOT_DRIVER_ALIAS(serial_mt7620, mediatek_mt7620_uart);
+
+#ifdef CONFIG_DEBUG_UART_MT7620
+
+#include <debug_uart.h>
+
+static inline void _debug_uart_init(void)
+{
+ struct mt7620_serial_plat plat;
+
+ plat.regs = (void *)CONFIG_DEBUG_UART_BASE;
+ plat.clock = CONFIG_DEBUG_UART_CLOCK;
+
+ writel(0, &plat.regs->ier);
+ writel(UART_MCRVAL, &plat.regs->mcr);
+ writel(UART_FCRVAL, &plat.regs->fcr);
+
+ _mt7620_serial_setbrg(&plat, CONFIG_BAUDRATE);
+}
+
+static inline void _debug_uart_putc(int ch)
+{
+ struct mt7620_serial_regs __iomem *regs =
+ (void *)CONFIG_DEBUG_UART_BASE;
+
+ while (!(readl(®s->lsr) & UART_LSR_THRE))
+ ;
+
+ writel(ch, ®s->thr);
+}
+
+DEBUG_UART_FUNCS
+
+#endif
--
2.17.1
More information about the U-Boot
mailing list