[PATCH v2 9/9] board: sl28: add OP-TEE Trusted OS support (bl32)

Michael Walle michael at walle.cc
Wed Nov 18 17:46:02 CET 2020


Add support to load the OP-TEE Trusted OS by the SPL.

Signed-off-by: Michael Walle <michael at walle.cc>
---
 .../dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi  | 36 +++++++++++++++++++
 board/kontron/sl28/Kconfig                    | 23 ++++++++++++
 board/kontron/sl28/sl28.c                     |  7 ++++
 3 files changed, 66 insertions(+)

diff --git a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi
index 54ef0b4258..65d5684973 100644
--- a/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-kontron-sl28-u-boot.dtsi
@@ -138,6 +138,42 @@
 };
 #endif
 
+#ifdef CONFIG_SL28_SPL_LOADS_OPTEE_BL32
+&binman {
+	fit {
+		images {
+			bl32 {
+				description = "OP-TEE Trusted OS (bl32)";
+				type = "firmware";
+				arch = "arm";
+				os = "tee";
+				compression = "none";
+				load = <CONFIG_SL28_BL32_ENTRY_ADDR>;
+				entry = <CONFIG_SL28_BL32_ENTRY_ADDR>;
+
+				blob-ext {
+					filename = "tee.bin";
+				};
+			};
+		};
+
+		configurations {
+			conf-1 {
+				loadables = "uboot", "bl32";
+			};
+
+			conf-2 {
+				loadables = "uboot", "bl32";
+			};
+
+			conf-3 {
+				loadables = "uboot", "bl32";
+			};
+		};
+	};
+};
+#endif
+
 &i2c0 {
 	rtc: rtc at 32 {
 	};
diff --git a/board/kontron/sl28/Kconfig b/board/kontron/sl28/Kconfig
index aba49fc115..4078ef186b 100644
--- a/board/kontron/sl28/Kconfig
+++ b/board/kontron/sl28/Kconfig
@@ -25,4 +25,27 @@ config SL28_SPL_LOADS_ATF_BL31
 	  Enable this to load a BL31 image by the SPL. You have to
 	  provde a bl31.bin in u-boot's root directory.
 
+if SL28_SPL_LOADS_ATF_BL31
+
+config SL28_BL31_ENTRY_ADDR
+	hex "Entry point of the BL31 image"
+	default 0xfbe00000
+
+endif
+
+config SL28_SPL_LOADS_OPTEE_BL32
+	bool "SPL loads OP-TEE Trusted OS as BL32"
+	depends on SL28_SPL_LOADS_ATF_BL31
+	help
+	  Enable this to load a BL32 image by the SPL. You have to
+	  provde a tee.bin in u-boot's root directory.
+
+if SL28_SPL_LOADS_OPTEE_BL32
+
+config SL28_BL32_ENTRY_ADDR
+	hex "Entry point of the BL32 image"
+	default 0xfc000000
+
+endif
+
 endif
diff --git a/board/kontron/sl28/sl28.c b/board/kontron/sl28/sl28.c
index b18127c4d1..34f17b486b 100644
--- a/board/kontron/sl28/sl28.c
+++ b/board/kontron/sl28/sl28.c
@@ -50,6 +50,7 @@ int ft_board_setup(void *blob, struct bd_info *bd)
 	u64 base[CONFIG_NR_DRAM_BANKS];
 	u64 size[CONFIG_NR_DRAM_BANKS];
 	int nbanks = CONFIG_NR_DRAM_BANKS;
+	int node;
 	int i;
 
 	ft_cpu_setup(blob, bd);
@@ -64,5 +65,11 @@ int ft_board_setup(void *blob, struct bd_info *bd)
 
 	fdt_fixup_icid(blob);
 
+	if (CONFIG_IS_ENABLED(SL28_SPL_LOADS_OPTEE_BL32)) {
+		node = fdt_node_offset_by_compatible(blob, -1, "linaro,optee-tz");
+		if (node)
+			fdt_set_node_status(blob, node, FDT_STATUS_OKAY, 0);
+	}
+
 	return 0;
 }
-- 
2.20.1



More information about the U-Boot mailing list