[PATCH 16/20] arm: dts: Add support for A72 specific J721S2 Common Processor Board

Aswath Govindraju a-govindraju at ti.com
Thu Dec 16 13:27:10 CET 2021


The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,

+------------------------------------------------------+
|   +-------------------------------------------+      |
|   |                                           |      |
|   |        Add-on Card 1 Options              |      |
|   |                                           |      |
|   +-------------------------------------------+      |
|                                                      |
|                                                      |
|                     +-------------------+            |
|                     |                   |            |
|                     |   SOM             |            |
|  +--------------+   |                   |            |
|  |              |   |                   |            |
|  |  Add-on      |   +-------------------+            |
|  |  Card 2      |                                    |    Power Supply
|  |  Options     |                                    |    |
|  |              |                                    |    |
|  +--------------+                                    | <---
+------------------------------------------------------+
                                 Common Processor Board

Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.

Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439

Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
---
 arch/arm/dts/Makefile                         |   1 +
 .../k3-j721s2-common-proc-board-u-boot.dtsi   | 146 ++++++
 arch/arm/dts/k3-j721s2-common-proc-board.dts  | 421 ++++++++++++++++++
 3 files changed, 568 insertions(+)
 create mode 100644 arch/arm/dts/k3-j721s2-common-proc-board-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-j721s2-common-proc-board.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7f622fedbda7..6aadfec7fac7 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1123,6 +1123,7 @@ dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
 			      k3-j721e-r5-common-proc-board.dtb \
 			      k3-j7200-common-proc-board.dtb \
 			      k3-j7200-r5-common-proc-board.dtb
+dtb-$(CONFIG_SOC_K3_J721S2) += k3-j721s2-common-proc-board.dtb
 dtb-$(CONFIG_SOC_K3_AM642) += k3-am642-evm.dtb \
 			      k3-am642-r5-evm.dtb \
 			      k3-am642-sk.dtb \
diff --git a/arch/arm/dts/k3-j721s2-common-proc-board-u-boot.dtsi b/arch/arm/dts/k3-j721s2-common-proc-board-u-boot.dtsi
new file mode 100644
index 000000000000..d4c42e8bd5ea
--- /dev/null
+++ b/arch/arm/dts/k3-j721s2-common-proc-board-u-boot.dtsi
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial10:115200n8";
+		tick-timer = &timer1;
+	};
+
+	aliases {
+		i2c0 = &wkup_i2c0;
+		i2c1 = &mcu_i2c0;
+		i2c2 = &mcu_i2c1;
+		i2c3 = &main_i2c0;
+		ethernet0 = &cpsw_port1;
+	};
+};
+
+&wkup_i2c0 {
+	u-boot,dm-spl;
+};
+
+&cbass_main {
+	u-boot,dm-spl;
+};
+
+&main_navss {
+	u-boot,dm-spl;
+};
+
+&cbass_mcu_wakeup {
+	u-boot,dm-spl;
+
+	timer1: timer at 40400000 {
+		compatible = "ti,omap5430-timer";
+		reg = <0x0 0x40400000 0x0 0x80>;
+		ti,timer-alwon;
+		clock-frequency = <25000000>;
+		u-boot,dm-spl;
+	};
+
+	chipid at 43000014 {
+		u-boot,dm-spl;
+	};
+};
+
+&mcu_navss {
+	u-boot,dm-spl;
+};
+
+&mcu_ringacc {
+	reg =   <0x0 0x2b800000 0x0 0x400000>,
+		<0x0 0x2b000000 0x0 0x400000>,
+		<0x0 0x28590000 0x0 0x100>,
+		<0x0 0x2a500000 0x0 0x40000>,
+		<0x0 0x28440000 0x0 0x40000>;
+	reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target", "cfg";
+	u-boot,dm-spl;
+};
+
+&mcu_udmap {
+	reg =   <0x0 0x285c0000 0x0 0x100>,
+		<0x0 0x284c0000 0x0 0x4000>,
+		<0x0 0x2a800000 0x0 0x40000>,
+		<0x0 0x284a0000 0x0 0x4000>,
+		<0x0 0x2aa00000 0x0 0x40000>,
+		<0x0 0x28400000 0x0 0x2000>;
+	reg-names = "gcfg", "rchan", "rchanrt", "tchan",
+		    "tchanrt", "rflow";
+	u-boot,dm-spl;
+};
+
+&secure_proxy_main {
+	u-boot,dm-spl;
+};
+
+&sms {
+	u-boot,dm-spl;
+	k3_sysreset: sysreset-controller {
+		compatible = "ti,sci-sysreset";
+		u-boot,dm-spl;
+	};
+};
+
+&main_pmx0 {
+	u-boot,dm-spl;
+};
+
+&main_uart8_pins_default {
+	u-boot,dm-spl;
+};
+
+&main_mmc1_pins_default {
+	u-boot,dm-spl;
+};
+
+&wkup_pmx0 {
+	u-boot,dm-spl;
+};
+
+&k3_pds {
+	u-boot,dm-spl;
+};
+
+&k3_clks {
+	u-boot,dm-spl;
+};
+
+&k3_reset {
+	u-boot,dm-spl;
+};
+
+&main_uart8 {
+	u-boot,dm-spl;
+};
+
+&mcu_uart0 {
+	u-boot,dm-spl;
+};
+
+&wkup_uart0 {
+	u-boot,dm-spl;
+};
+
+&mcu_cpsw {
+	reg = <0x0 0x46000000 0x0 0x200000>,
+	      <0x0 0x40f00200 0x0 0x8>;
+	reg-names = "cpsw_nuss", "mac_efuse";
+	/delete-property/ ranges;
+
+	cpsw-phy-sel at 40f04040 {
+		compatible = "ti,am654-cpsw-phy-sel";
+		reg= <0x0 0x40f04040 0x0 0x4>;
+		reg-names = "gmii-sel";
+	};
+};
+
+&main_sdhci0 {
+	u-boot,dm-spl;
+};
+
+&main_sdhci1 {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/k3-j721s2-common-proc-board.dts b/arch/arm/dts/k3-j721s2-common-proc-board.dts
new file mode 100644
index 000000000000..19c445a5dd3f
--- /dev/null
+++ b/arch/arm/dts/k3-j721s2-common-proc-board.dts
@@ -0,0 +1,421 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439
+ */
+
+/dts-v1/;
+
+#include "k3-j721s2-som-p0.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	compatible = "ti,j721s2-evm", "ti,j721s2";
+	model = "Texas Instruments J721S2 EVM";
+
+	chosen {
+		stdout-path = "serial10:115200n8";
+		bootargs = "console=ttyS10,115200n8 earlycon=ns16550a,mmio32,2880000";
+	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: fixedregulator-sd {
+		/* Output of TPS22918 */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: gpio-regulator-TLV71033 {
+		/* Output of TLV71033 */
+		compatible = "regulator-gpio";
+		regulator-name = "tlv71033";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_5v0>;
+		gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
+	transceiver1: can-phy1 {
+		compatible = "ti,tcan1043";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 69 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver2: can-phy2 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
+	};
+
+};
+
+&main_pmx0 {
+	main_uart8_pins_default: main-uart8-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x040, PIN_INPUT, 14) /* (AC28) MCASP0_AXR0.UART8_CTSn */
+			J721S2_IOPAD(0x044, PIN_OUTPUT, 14) /* (Y26) MCASP0_AXR1.UART8_RTSn */
+			J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
+			J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
+		>;
+	};
+
+	main_i2c3_pins_default: main-i2c3-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x064, PIN_INPUT_PULLUP, 13) /* (W28) MCAN0_TX.I2C3_SCL */
+			J721S2_IOPAD(0x060, PIN_INPUT_PULLUP, 13) /* (AC27) MCASP2_AXR1.I2C3_SDA */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
+			J721S2_IOPAD(0x108, PIN_INPUT, 0) /* (N24) MMC1_CMD */
+			J721S2_IOPAD(0x100, PIN_INPUT, 0) /* (###) MMC1_CLKLB */
+			J721S2_IOPAD(0x0fc, PIN_INPUT, 0) /* (M23) MMC1_DAT0 */
+			J721S2_IOPAD(0x0f8, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+			J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
+			J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
+			J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
+		>;
+	};
+};
+
+&wkup_pmx0 {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
+			J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
+			J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
+			J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
+			J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
+			J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
+			J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
+			J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
+			J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
+			J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
+			J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
+			J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu-mdio-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
+			J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
+		>;
+	};
+
+	mcu_mcan0_pins_default: mcu-mcan0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
+			J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan1_pins_default: mcu-mcan1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
+			J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0c0, PIN_INPUT, 7) /* (D26) WKUP_GPIO0_0 */
+			J721S2_WKUP_IOPAD(0x0a8, PIN_INPUT, 7) /* (B25) MCU_SPI0_D1.WKUP_GPIO0_69 */
+		>;
+	};
+
+	mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
+		>;
+	};
+};
+
+&main_gpio2 {
+	status = "disabled";
+};
+
+&main_gpio4 {
+	status = "disabled";
+};
+
+&main_gpio6 {
+	status = "disabled";
+};
+
+&wkup_gpio1 {
+	status = "disabled";
+};
+
+&wkup_uart0 {
+	status = "reserved";
+};
+
+&main_uart0 {
+	status = "disabled";
+};
+
+&main_uart1 {
+	status = "disabled";
+};
+
+&main_uart2 {
+	status = "disabled";
+};
+
+&main_uart3 {
+	status = "disabled";
+};
+
+&main_uart4 {
+	status = "disabled";
+};
+
+&main_uart5 {
+	status = "disabled";
+};
+
+&main_uart6 {
+	status = "disabled";
+};
+
+&main_uart7 {
+	status = "disabled";
+};
+
+&main_uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart8_pins_default>;
+	/* Shared with TFA on this platform */
+	power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
+};
+
+&main_uart9 {
+	status = "disabled";
+};
+
+&main_i2c0 {
+	clock-frequency = <400000>;
+
+	exp1: gpio at 20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PCIE_2L_MODE_SEL", "PCIE_2L_PERSTZ", "PCIE_2L_RC_RSTZ",
+				  "PCIE_2L_EP_RST_EN", "PCIE_1L_MODE_SEL", "PCIE_1L_PERSTZ",
+				  "PCIE_1L_RC_RSTZ", "PCIE_1L_EP_RST_EN", "PCIE_2L_PRSNT#",
+				  "PCIE_1L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3", "EXP_MUX1",
+				  "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTz";
+	};
+
+	exp2: gpio at 22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "APPLE_AUTH_RSTZ", "MLB_RSTZ", "GPIO_USD_PWR_EN", "USBC_PWR_EN",
+				  "USBC_MODE_SEL1", "USBC_MODE_SEL0", "MCAN0_EN", "MCAN0_STB#",
+				  "MUX_SPAREMUX_SPARE", "MCASP/TRACE_MUX_S0", "MCASP/TRACE_MUX_S1",
+				  "MLB_MUX_SEL", "MCAN_MUX_SEL", "MCASP2/SPI3_MUX_SEL", "PCIe_CLKREQn_MUX_SEL",
+				  "CDCI2_RSTZ", "ENET_EXP_PWRDN", "ENET_EXP_RESETZ", "ENET_I2CMUX_SEL",
+				  "ENET_EXP_SPARE2", "M2PCIE_RTSZ", "USER_INPUT1", "USER_LED1", "USER_LED2";
+	};
+};
+
+&main_i2c1 {
+	status = "disabled";
+};
+
+&main_i2c2 {
+	status = "disabled";
+};
+
+&main_i2c3 {
+	status = "disabled";
+};
+
+&main_i2c4 {
+	status = "disabled";
+};
+
+&main_i2c5 {
+	status = "disabled";
+};
+
+&main_i2c6 {
+	status = "disabled";
+};
+
+&main_sdhci0 {
+	/* eMMC */
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_sdhci1 {
+	/* SD card */
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
+	disable-wp;
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy at 0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&phy0>;
+};
+
+&mcu_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan0_pins_default>;
+	phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan1_pins_default>;
+	phys = <&transceiver2>;
+};
+
+&main_mcan0 {
+	status = "disabled";
+};
+
+&main_mcan1 {
+	status = "disabled";
+};
+
+&main_mcan2 {
+	status = "disabled";
+};
+
+&main_mcan3 {
+	status = "disabled";
+};
+
+&main_mcan4 {
+	status = "disabled";
+};
+
+&main_mcan5 {
+	status = "disabled";
+};
+
+&main_mcan6 {
+	status = "disabled";
+};
+
+&main_mcan7 {
+	status = "disabled";
+};
+
+&main_mcan8 {
+	status = "disabled";
+};
+
+&main_mcan9 {
+	status = "disabled";
+};
+
+&main_mcan10 {
+	status = "disabled";
+};
+
+&main_mcan11 {
+	status = "disabled";
+};
+
+&main_mcan12 {
+	status = "disabled";
+};
+
+&main_mcan13 {
+	status = "disabled";
+};
+
+&main_mcan14 {
+	status = "disabled";
+};
+
+&main_mcan15 {
+	status = "disabled";
+};
+
+&main_mcan17 {
+	status = "disabled";
+};
-- 
2.17.1



More information about the U-Boot mailing list