[PATCH 4/4] board: keymile: add support for seli8 design based on nxp ls102x soc
Aleksandar Gerasimovski
aleksandar.gerasimovski at hitachi-powergrids.com
Wed Jan 13 17:21:19 CET 2021
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung at hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni at hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski at hitachi-powergrids.com>
---
arch/arm/Kconfig | 19 ++
arch/arm/dts/Makefile | 2 +
arch/arm/dts/ls1021a-pg-wcom-seli8.dts | 111 +++++++++
board/keymile/Kconfig | 23 +-
board/keymile/common/ivm.c | 19 +-
board/keymile/pg-wcom-ls102xa/Kconfig | 19 ++
board/keymile/pg-wcom-ls102xa/MAINTAINERS | 10 +
board/keymile/pg-wcom-ls102xa/Makefile | 11 +
board/keymile/pg-wcom-ls102xa/ddr.c | 90 +++++++
board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c | 160 ++++++++++++
configs/pg_wcom_seli8_defconfig | 63 +++++
include/configs/km/pg-wcom-ls102xa.h | 309 ++++++++++++++++++++++++
include/configs/pg-wcom-seli8.h | 45 ++++
13 files changed, 870 insertions(+), 11 deletions(-)
create mode 100644 arch/arm/dts/ls1021a-pg-wcom-seli8.dts
create mode 100644 board/keymile/pg-wcom-ls102xa/Kconfig
create mode 100644 board/keymile/pg-wcom-ls102xa/MAINTAINERS
create mode 100644 board/keymile/pg-wcom-ls102xa/Makefile
create mode 100644 board/keymile/pg-wcom-ls102xa/ddr.c
create mode 100644 board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c
create mode 100644 configs/pg_wcom_seli8_defconfig
create mode 100644 include/configs/km/pg-wcom-ls102xa.h
create mode 100644 include/configs/pg-wcom-seli8.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index fbe9087..13fdf3c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1515,6 +1515,24 @@ config TARGET_LS1021ATWR
select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
imply SCSI
+config TARGET_PG_WCOM_SELI8
+ bool "Support Hitachi-Powergrids SELI8 service unit card"
+ select ARCH_LS1021A
+ select ARCH_SUPPORT_PSCI
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select CPU_V7A
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SYS_FSL_DDR
+ select FSL_DDR_INTERACTIVE
+ select VENDOR_KM
+ imply SCSI
+ help
+ Support for Hitachi-Powergrids SELI8 service unit card.
+ SELI8 is a QorIQ LS1021a based service unit card used
+ in XMC20 and FOX615 product families.
+
config TARGET_LS1021ATSN
bool "Support ls1021atsn"
select ARCH_LS1021A
@@ -2034,6 +2052,7 @@ source "board/variscite/dart_6ul/Kconfig"
source "board/vscom/baltos/Kconfig"
source "board/phytium/durian/Kconfig"
source "board/xen/xenguest_arm64/Kconfig"
+source "board/keymile/Kconfig"
source "arch/arm/Kconfig.debug"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index fd47e40..ec93f93 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -393,6 +393,8 @@ dtb-$(CONFIG_ARCH_LS1021A) += ls1021a-qds-duart.dtb \
ls1021a-qds-lpuart.dtb \
ls1021a-twr-duart.dtb ls1021a-twr-lpuart.dtb \
ls1021a-iot-duart.dtb ls1021a-tsn.dtb
+dtb-$(CONFIG_TARGET_PG_WCOM_SELI8) += ls1021a-pg-wcom-seli8.dtb
+
dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
fsl-ls2080a-qds-42-x.dtb \
fsl-ls2080a-rdb.dtb \
diff --git a/arch/arm/dts/ls1021a-pg-wcom-seli8.dts b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts
new file mode 100644
index 0000000..e335188
--- /dev/null
+++ b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2013-2015 Freescale Semiconductor, Inc.
+ * Copyright 2020 Hitachi Power Grids. All rights reserved.
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+ model = "Hitachi-Powergrids SELI8 Service Unit for XMC and FOX";
+
+ chosen {
+ stdout-path = &uart0;
+ };
+};
+
+&enet0 {
+ status = "okay";
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&enet1 {
+ status = "okay";
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&enet2 {
+ phy-handle = <&debug_phy>;
+ phy-connection-type = "rgmii-id";
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NOR Flash on board */
+ ranges = <0x0 0x0 0x60000000 0x04000000>;
+ status = "okay";
+
+ nor at 0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x4000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition at 0 {
+ label = "rcw";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+ partition at 20000 {
+ label = "qe";
+ reg = <0x20000 0x20000>;
+ };
+ partition at 40000 {
+ label = "envred";
+ reg = <0x40000 0x20000>;
+ };
+ partition at 60000 {
+ label = "env";
+ reg = <0x60000 0x20000>;
+ };
+ partition at 100000 {
+ label = "u-boot";
+ reg = <0x100000 0x100000>;
+ };
+ partition at 200000 {
+ label = "ubi0";
+ reg = <0x200000 0x3E00000>;
+ };
+ };
+};
+
+&mdio0 {
+ debug_phy: ethernet-phy at 11 {
+ reg = <0x11>;
+ };
+
+ tbi0: tbi-phy at 0xb {
+ reg = <0xb>;
+ device_type = "tbi-phy";
+ };
+};
+
+&mdio1 {
+ tbi1: tbi-phy at 0xd {
+ reg = <0xd>;
+ device_type = "tbi-phy";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig
index e590690..965a537 100644
--- a/board/keymile/Kconfig
+++ b/board/keymile/Kconfig
@@ -20,8 +20,8 @@ config KM_PNVRAM
config KM_PHRAM
hex "Physical RAM"
- default 0x17F000 if ARM
- default 0x100000 if PPC
+ default 0x17F000 if ARM && !ARCH_LS1021A
+ default 0x100000 if PPC || ARCH_LS1021A
depends on !ARCH_SOCFPGA
help
Start address of the physical RAM, which is the mounted /var folder.
@@ -30,13 +30,14 @@ config KM_RESERVED_PRAM
hex "Reserved RAM"
default 0x801000 if ARCH_KIRKWOOD
default 0x0 if MPC83xx
- default 0x1000 if MPC85xx
+ default 0x1000 if MPC85xx || ARCH_LS1021A
depends on !ARCH_SOCFPGA
help
Reserved physical RAM area at the end of memory for special purposes.
config KM_CRAMFS_ADDR
hex "CRAMFS Address"
+ default 0x83000000 if ARCH_LS1021A
default 0x3000000
depends on !ARCH_SOCFPGA
help
@@ -44,16 +45,25 @@ config KM_CRAMFS_ADDR
config KM_KERNEL_ADDR
hex "Kernel Load Address"
+ default 0x82000000 if ARCH_LS1021A
default 0x2000000
help
Address where to load Linux kernel in RAM.
config KM_FDT_ADDR
hex "FDT Load Address"
+ default 0x82FC0000 if ARCH_LS1021A
default 0x2FC0000
help
Address where to load flattened device tree in RAM.
+config SYS_PAX_BASE
+ hex "PAX IFC Base Address"
+ default 0x78000000
+ depends on ARCH_LS1021A
+ help
+ IFC Base Address for PAXx FPGA.
+
config KM_CONSOLE_TTY
string "KM Console"
default "ttyS0"
@@ -69,9 +79,9 @@ config KM_DEF_NETDEV
config KM_COMMON_ETH_INIT
bool "Common Ethernet Initialization"
default y if ARCH_KIRKWOOD || MPC83xx
- default n if MPC85xx || ARCH_SOCFPGA
+ default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A
help
- Use the Ethernet initialization implemented in common code, which
+ Use the Ethernet initialization implemented in common code that
detects if a Piggy board is present.
config PIGGY_MAC_ADDRESS_OFFSET
@@ -90,7 +100,7 @@ config KM_MVEXTSW_ADDR
config KM_IVM_BUS
int "IVM I2C Bus"
default 0 if ARCH_SOCFPGA
- default 1 if ARCH_KIRKWOOD || MPC85xx
+ default 1 if ARCH_KIRKWOOD || MPC85xx || ARCH_LS1021A
default 2 if MPC83xx
help
Identifier number of I2C bus, where the inventory EEPROM is connected to.
@@ -116,6 +126,7 @@ config SYS_IVM_EEPROM_PAGE_LEN
source "board/keymile/km83xx/Kconfig"
source "board/keymile/kmp204x/Kconfig"
source "board/keymile/km_arm/Kconfig"
+source "board/keymile/pg-wcom-ls102xa/Kconfig"
endmenu
diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c
index e989bf6..48817cb 100644
--- a/board/keymile/common/ivm.c
+++ b/board/keymile/common/ivm.c
@@ -306,11 +306,7 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset)
return 0;
page2 = &buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN * 2];
- if (!IS_ENABLED(CONFIG_KMTEGR1)) {
- /* if an offset is defined, add it */
- process_mac(valbuf, page2, mac_address_offset, true);
- env_set((char *)"ethaddr", (char *)valbuf);
- } else {
+ if (IS_ENABLED(CONFIG_KMTEGR1)) {
/* KMTEGR1 has a special setup. eth0 has no connection to the
* outside and gets an locally administred MAC address, eth1 is
* the debug interface and gets the official MAC address from
@@ -320,6 +316,19 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset)
env_set((char *)"ethaddr", (char *)valbuf);
process_mac(valbuf, page2, mac_address_offset, true);
env_set((char *)"eth1addr", (char *)valbuf);
+ } else if (IS_ENABLED(CONFIG_ARCH_LS1021A)) {
+ /* LS102xA has 1xRGMII for debug connection and
+ * 2xSGMII for back-plane mgmt connection
+ */
+ process_mac(valbuf, page2, 1, true);
+ env_set((char *)"ethaddr", (char *)valbuf);
+ process_mac(valbuf, page2, 2, true);
+ env_set((char *)"eth1addr", (char *)valbuf);
+ process_mac(valbuf, page2, mac_address_offset, true);
+ env_set((char *)"eth2addr", (char *)valbuf);
+ } else {
+ process_mac(valbuf, page2, mac_address_offset, true);
+ env_set((char *)"ethaddr", (char *)valbuf);
}
return 0;
diff --git a/board/keymile/pg-wcom-ls102xa/Kconfig b/board/keymile/pg-wcom-ls102xa/Kconfig
new file mode 100644
index 0000000..15c009d
--- /dev/null
+++ b/board/keymile/pg-wcom-ls102xa/Kconfig
@@ -0,0 +1,19 @@
+if TARGET_PG_WCOM_SELI8
+
+config SYS_BOARD
+ default "pg-wcom-ls102xa"
+
+config SYS_VENDOR
+ default "keymile"
+
+config SYS_SOC
+ default "ls102xa"
+
+config SYS_CONFIG_NAME
+ default "pg-wcom-seli8"
+
+config BOARD_SPECIFIC_OPTIONS
+ def_bool y
+ imply FS_CRAMFS
+
+endif
diff --git a/board/keymile/pg-wcom-ls102xa/MAINTAINERS b/board/keymile/pg-wcom-ls102xa/MAINTAINERS
new file mode 100644
index 0000000..e1bc90a
--- /dev/null
+++ b/board/keymile/pg-wcom-ls102xa/MAINTAINERS
@@ -0,0 +1,10 @@
+Hitachi Power Grids LS102XA BOARD
+M: Aleksandar Gerasimovski <aleksandar.gerasimovski at hitachi-powergrids.com>
+M: Rainer Boschung <rainer.boschung at hitachi-powergrids.com>
+M: Matteo Ghidoni <matteo.ghidoni at hitachi-powergrids.com>
+S: Maintained
+F: board/keymile/pg-wcom-ls102xa/
+F: include/configs/km/pg-wcom-ls102xa.h
+F: include/configs/pg-wcom-seli8.h
+F: configs/pg_wcom_seli8_defconfig
+F: arch/arm/dts/ls1021a-pg-wcom-seli8.dts
diff --git a/board/keymile/pg-wcom-ls102xa/Makefile b/board/keymile/pg-wcom-ls102xa/Makefile
new file mode 100644
index 0000000..229b0c2
--- /dev/null
+++ b/board/keymile/pg-wcom-ls102xa/Makefile
@@ -0,0 +1,11 @@
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright 2021 Hitachi Power Grids. All rights reserved.
+#
+
+obj-y += pg-wcom-ls102xa.o ddr.o
+obj-y += ../common/common.o ../common/ivm.o ../common/qrio.o
+obj-$(CONFIG_LAYERSCAPE_NS_ACCESS) += ../../freescale/common/ns_access.o
+obj-$(CONFIG_LS102XA_STREAM_ID) += ../../freescale/common/ls102xa_stream_id.o
+obj-$(CONFIG_ID_EEPROM) += ../../freescale/common/sys_eeprom.o
diff --git a/board/keymile/pg-wcom-ls102xa/ddr.c b/board/keymile/pg-wcom-ls102xa/ddr.c
new file mode 100644
index 0000000..6023573
--- /dev/null
+++ b/board/keymile/pg-wcom-ls102xa/ddr.c
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020 Hitachi Power Grids. All rights reserved.
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/ls102xa_soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+
+ // 1/2 DRAM cycle (should be increased in case of ADDR/CMD heavily loaded than the clock)
+ popts->clk_adjust = 0x4;
+ popts->write_data_delay = 0x4;
+ // wr leveling start value for lane 0
+ popts->wrlvl_start = 0x5;
+ // wr leveling start values for lanes 1-3 (lane 4 not there)
+ popts->wrlvl_ctl_2 = 0x05050500;
+ // 32-bit DRAM, no need to set start values for lanes we do not have (5-8)
+ popts->wrlvl_ctl_3 = 0x0;
+ popts->cpo_override = 0x1f;
+
+ /* force DDR bus width to 32 bits */
+ popts->data_bus_width = 1;
+ popts->otf_burst_chop_en = 0;
+ popts->burst_length = DDR_BL8;
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ popts->cswl_override = DDR_CSWL_CS0;
+
+ /* optimize cpo for erratum A-009942 */
+ popts->cpo_sample = 0x58;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+int fsl_initdram(void)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing DDR....using SPD\n");
+ dram_size = fsl_ddr_sdram();
+
+ erratum_a008850_post();
+
+ gd->ram_size = dram_size;
+
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = gd->ram_size;
+
+ return 0;
+}
diff --git a/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c
new file mode 100644
index 0000000..6b0e963
--- /dev/null
+++ b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 Hitachi Power Grids. All rights reserved.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/immap_ls102xa.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/ls102xa_devdis.h>
+#include <asm/arch/ls102xa_soc.h>
+#include <hwconfig.h>
+#include <mmc.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <fsl_ifc.h>
+#include <fsl_immap.h>
+#include <netdev.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <fsl_sec.h>
+#include <fsl_devdis.h>
+#include <fsl_ddr.h>
+#include <spl.h>
+#include <fdt_support.h>
+#include <fsl_qe.h>
+#include <fsl_validate.h>
+
+#include "../common/common.h"
+#include "../common/qrio.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
+
+int checkboard(void)
+{
+ show_qrio();
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ return fsl_initdram();
+}
+
+int board_early_init_f(void)
+{
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL};
+
+ /* Disable unused MCK1 */
+ setbits_be32(&gur->ddrclkdr, 2);
+
+ /* IFC Global Configuration */
+ setbits_be32(&ifc.gregs->ifc_gcr, 12 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
+ setbits_be32(&ifc.gregs->ifc_ccr, IFC_CCR_CLK_DIV(3) |
+ IFC_CCR_INV_CLK_EN);
+
+ /* clear BD & FR bits for BE BD's and frame data */
+ clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
+
+ init_early_memctl_regs();
+
+ /* QRIO Configuration */
+ qrio_uprstreq(UPREQ_CORE_RST);
+
+ if (IS_ENABLED(CONFIG_TARGET_PG_WCOM_SELI8)) {
+ qrio_prstcfg(KM_LIU_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_LIU_RST, true);
+
+ qrio_prstcfg(KM_PAXK_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_PAXK_RST, true);
+
+ qrio_prstcfg(KM_DBG_ETH_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+ qrio_prst(KM_DBG_ETH_RST, false, false);
+ }
+
+ i2c_deblock_gpio_cfg();
+
+ arch_soc_init();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ if (IS_ENABLED(CONFIG_SYS_FSL_ERRATUM_A010315))
+ erratum_a010315();
+
+ fsl_serdes_init();
+
+ ls102xa_smmu_stream_id_init();
+
+ u_qe_init();
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ if (IS_ENABLED(CONFIG_FSL_DEVICE_DISABLE))
+ device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl));
+
+ ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
+ CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ ft_cpu_setup(blob, bd);
+
+ if (IS_ENABLED(CONFIG_PCI))
+ ft_pci_setup(blob, bd);
+
+ return 0;
+}
+
+u8 flash_read8(void *addr)
+{
+ return __raw_readb(addr + 1);
+}
+
+void flash_write16(u16 val, void *addr)
+{
+ u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
+
+ __raw_writew(shftval, addr);
+}
+
+u16 flash_read16(void *addr)
+{
+ u16 val = __raw_readw(addr);
+
+ return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
+}
+
+int hush_init_var(void)
+{
+ ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
+ return 0;
+}
+
+int last_stage_init(void)
+{
+ set_km_env();
+ return 0;
+}
diff --git a/configs/pg_wcom_seli8_defconfig b/configs/pg_wcom_seli8_defconfig
new file mode 100644
index 0000000..2d58fa0
--- /dev/null
+++ b/configs/pg_wcom_seli8_defconfig
@@ -0,0 +1,63 @@
+CONFIG_ARM=y
+CONFIG_TARGET_PG_WCOM_SELI8=y
+CONFIG_SYS_TEXT_BASE=0x60100000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_KM_DEF_NETDEV="eth2"
+CONFIG_KM_COMMON_ETH_INIT=y
+CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3
+CONFIG_SYS_MEMTEST_START=0x80000000
+CONFIG_SYS_MEMTEST_END=0x9fffffff
+CONFIG_ENV_SIZE=0x4000
+CONFIG_ENV_SECT_SIZE=0x20000
+CONFIG_BOOTCOUNT_BOOTLIMIT=3
+CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
+CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-seli8"
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
+CONFIG_SILENT_CONSOLE=y
+CONFIG_MISC_INIT_R=y
+CONFIG_LAST_STAGE_INIT=y
+CONFIG_CMD_IMLS=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+CONFIG_CMD_CRAMFS=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),-(ubi0);68000000.flash:-(ubi1)"
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FLASH=y
+CONFIG_ENV_ADDR=0x60060000
+CONFIG_DM=y
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_SYS_FSL_DDR3=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_PHY_GIGE=y
+CONFIG_MII=y
+CONFIG_TSEC_ENET=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_DM_SERIAL=y
+CONFIG_SYS_NS16550=y
diff --git a/include/configs/km/pg-wcom-ls102xa.h b/include/configs/km/pg-wcom-ls102xa.h
new file mode 100644
index 0000000..55fb909
--- /dev/null
+++ b/include/configs/km/pg-wcom-ls102xa.h
@@ -0,0 +1,309 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2020 Hitachi Power Grids. All rights reserved.
+ */
+
+#ifndef __CONFIG_PG_WCOM_LS102XA_H
+#define __CONFIG_PG_WCOM_LS102XA_H
+
+#define CONFIG_SYS_FSL_CLK
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
+
+#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
+
+#define CONFIG_SYS_CLK_FREQ 66666666
+/*
+ * Take into account default implementation where DDR_FDBK_MULTI is consider as
+ * configured for DDR_PLL = 2*MEM_PLL_RAT.
+ * In our case DDR_FDBK_MULTI is 2, means DDR_PLL = MEM_PLL_RAT.
+ */
+#define CONFIG_DDR_CLK_FREQ (100000000 >> 1)
+
+#define PHYS_SDRAM 0x80000000
+#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+
+#define CONFIG_DDR_SPD
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x54
+
+/*
+ * IFC Definitions
+ */
+/* NOR Flash Definitions */
+#define CONFIG_FSL_IFC
+#define CONFIG_SYS_FLASH_BASE 0x60000000
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_TE | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(64 * 1024 * 1024)
+
+#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_AVD_TGL_PGM_EN | \
+ CSOR_NOR_ADM_SHIFT(0x4) | \
+ CSOR_NOR_NOR_MODE_AYSNC_NOR | \
+ CSOR_NOR_TRHZ_20 | \
+ CSOR_NOR_BCTLD)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \
+ FTIM0_NOR_TEADC(0x7) | \
+ FTIM0_NOR_TAVDS(0x0) | \
+ FTIM0_NOR_TEAHC(0x1))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \
+ FTIM1_NOR_TRAD_NOR(0x21) | \
+ FTIM1_NOR_TSEQRAD_NOR(0x21))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) | \
+ FTIM2_NOR_TCH(0x1) | \
+ FTIM2_NOR_TWPH(0x6) | \
+ FTIM2_NOR_TWP(0xb))
+#define CONFIG_SYS_NOR_FTIM3 0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }
+
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+/* NAND Flash Definitions */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0x68000000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_TE | \
+ CSPR_MSEL_NAND | \
+ CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN \
+ | CSOR_NAND_ECC_DEC_EN \
+ | CSOR_NAND_ECC_MODE_4 \
+ | CSOR_NAND_RAL_3 \
+ | CSOR_NAND_PGS_2K \
+ | CSOR_NAND_SPRZ_64 \
+ | CSOR_NAND_PB(64) \
+ | CSOR_NAND_TRHZ_40 \
+ | CSOR_NAND_BCTLD)
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x3) | \
+ FTIM0_NAND_TWP(0x8) | \
+ FTIM0_NAND_TWCHT(0x3) | \
+ FTIM0_NAND_TWH(0x5))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1e) | \
+ FTIM1_NAND_TWBE(0x1e) | \
+ FTIM1_NAND_TRR(0x6) | \
+ FTIM1_NAND_TRP(0x8))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x9) | \
+ FTIM2_NAND_TREH(0x5) | \
+ FTIM2_NAND_TWHRE(0x3c))
+#define CONFIG_SYS_NAND_FTIM3 (FTIM3_NAND_TWW(0x1e))
+
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* QRIO FPGA Definitions */
+#define CONFIG_SYS_QRIO_BASE 0x70000000
+#define CONFIG_SYS_QRIO_BASE_PHYS CONFIG_SYS_QRIO_BASE
+
+#define CONFIG_SYS_CSPR2_EXT (0x00)
+#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_TE | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_AMASK2 IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CSOR2 (CSOR_GPCM_ADM_SHIFT(0x4) | \
+ CSOR_GPCM_TRHZ_20 | \
+ CSOR_GPCM_BCTLD)
+#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x2) | \
+ FTIM0_GPCM_TEADC(0x8) | \
+ FTIM0_GPCM_TEAHC(0x2))
+#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x2) | \
+ FTIM1_GPCM_TRAD(0x6))
+#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x1) | \
+ FTIM2_GPCM_TCH(0x1) | \
+ FTIM2_GPCM_TWP(0x7))
+#define CONFIG_SYS_CS2_FTIM3 0x04000000
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_NUM_I2C_BUSES 3
+#define I2C_MUX_PCA_ADDR 0x70
+#define I2C_MUX_CH_DEFAULT 0x0
+#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
+ {1, {I2C_NULL_HOP} }, \
+ }
+
+#ifndef __ASSEMBLY__
+void set_sda(int state);
+void set_scl(int state);
+int get_sda(void);
+int get_scl(void);
+#endif
+
+/*
+ * eTSEC
+ */
+#ifdef CONFIG_TSEC_ENET
+#define CONFIG_ETHPRIME "ethernet at 2d90000"
+#endif
+
+#define CONFIG_CMDLINE_TAG
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+#define CONFIG_SMP_PEN_ADDR 0x01ee0200
+#define COUNTER_FREQUENCY 12500000
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE 256
+#define CONFIG_FSL_DEVICE_DISABLE
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_SYS_LOAD_ADDR 0x82000000
+
+#define CONFIG_LS102XA_STREAM_ID
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_LEN 0x100000 /* 1Mbyte */
+#define CONFIG_SYS_QE_FW_ADDR 0x60020000
+
+#define CONFIG_SYS_BOOTCOUNT_BE
+
+/*
+ * Environment
+ */
+
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
+
+#define CONFIG_ENV_TOTAL_SIZE 0x40000
+#define ENV_DEL_ADDR 0x60040000 /* direct for newenv */
+
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV
+#endif
+
+#ifndef CONFIG_KM_DEF_BOOT_ARGS_CPU
+#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
+#endif
+
+#define CONFIG_KM_DEF_ENV_CPU \
+ "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
+ "cramfsloadfdt=" \
+ "cramfsload ${fdt_addr_r} " \
+ "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
+ "u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \
+ "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize} && " \
+ "erase " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize} && " \
+ "cp.b ${load_addr_r} " \
+ __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize} && " \
+ "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize}\0" \
+ "update-nor=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \
+ " +${filesize} && " \
+ "erase " __stringify(CONFIG_SYS_FLASH_BASE) \
+ " +${filesize} && " \
+ "cp.b ${load_addr_r} " \
+ __stringify(CONFIG_SYS_FLASH_BASE) " ${filesize} && " \
+ "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +" __stringify(CONFIG_SYS_MONITOR_LEN)"\0" \
+ "set_fdthigh=true\0" \
+ "checkfdt=true\0" \
+ ""
+
+#define CONFIG_KM_NEW_ENV \
+ "newenv=protect off " __stringify(ENV_DEL_ADDR) \
+ " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \
+ "erase " __stringify(ENV_DEL_ADDR) \
+ " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \
+ "protect on " __stringify(ENV_DEL_ADDR) \
+ " +" __stringify(CONFIG_ENV_TOTAL_SIZE) "\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_NEW_ENV \
+ CONFIG_KM_DEF_ENV \
+ "EEprom_ivm=pca9547:70:9\0" \
+ ""
+
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Increase map for Linux */
+
+#endif
diff --git a/include/configs/pg-wcom-seli8.h b/include/configs/pg-wcom-seli8.h
new file mode 100644
index 0000000..9a7669c
--- /dev/null
+++ b/include/configs/pg-wcom-seli8.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2020 Hitachi Power Grids. All rights reserved.
+ */
+
+#ifndef __CONFIG_PG_WCOM_SELI8_H
+#define __CONFIG_PG_WCOM_SELI8_H
+
+#define CONFIG_HOSTNAME "SELI8"
+
+#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0"
+#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1"
+
+/* PAXK FPGA Definitions */
+#define CONFIG_SYS_CSPR3_EXT (0x00)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_PAX_BASE) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CSOR3 (CSOR_GPCM_ADM_SHIFT(0x4) | \
+ CSOR_GPCM_TRHZ_40)
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x6) | \
+ FTIM0_GPCM_TEADC(0x7) | \
+ FTIM0_GPCM_TEAHC(0x2))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x2) | \
+ FTIM1_GPCM_TRAD(0x12))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x3) | \
+ FTIM2_GPCM_TCH(0x1) | \
+ FTIM2_GPCM_TWP(0x12))
+#define CONFIG_SYS_CS3_FTIM3 0x04000000
+
+/* PRST */
+#define KM_LIU_RST 0
+#define KM_PAXK_RST 1
+#define KM_DBG_ETH_RST 15
+
+/* QRIO GPIOs used for deblocking */
+#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A
+#define KM_I2C_DEBLOCK_SCL 20
+#define KM_I2C_DEBLOCK_SDA 21
+
+#include "km/pg-wcom-ls102xa.h"
+
+#endif /* __CONFIG_PG_WCOM_SELI8_H */
--
1.8.3.1
More information about the U-Boot
mailing list