[PATCH 3/4] usb: musb: Fix handling interrupts for EP0 and SET ADDRESS commmand

[Lukasz Majewski]

Hi Pali,

> On Saturday 23 January 2021 16:16:11 Lukasz Majewski wrote:
> > Hi Pali,
> >   
> > > Interrupt for EP0 is indicated in intrtx register via first bit.
> > > It is set for both RX and TX. First bit in intrrx register is
> > > reserved and not set.
> > > 
> > > So remove calling musb_peri_ep0() function at every iteration of
> > > udc_irq() and musb_peri_rx() and call it only from musb_peri_tx()
> > > when correct interrupt bit in initrtx it set.
> > > 
> > > Address from SET ADDRESS command must be set to faddr register
> > > only after acknowledging SERV_RXPKTRDY followed by received EP0
> > > interrupt. So prior calling musb_peri_ep0_set_address() check for
> > > EP0 interrupt instead of (incorrect) MUSB_INTR_SOF interrupt.
> > > 
> > > This patch fixes issue that host (computer) cannot register
> > > U-Boot USB device and failing with errors:
> > > 
> > >     usb 1-1: new full-speed USB device number 86 using xhci_hcd
> > >     usb 1-1: Device not responding to setup address.
> > >     usb 1-1: Device not responding to setup address.
> > >     usb 1-1: device not accepting address 86, error -71
> > > 
> > > U-Boot was writing address to faddr register too early and did not
> > > wait for correct interrupt after which should update address.
> > > 
> > > Signed-off-by: Pali Rohár <pali at kernel.org>
> > > ---
> > >  drivers/usb/musb/musb_udc.c | 12 ++++--------
> > >  1 file changed, 4 insertions(+), 8 deletions(-)
> > > 
> > > diff --git a/drivers/usb/musb/musb_udc.c
> > > b/drivers/usb/musb/musb_udc.c index 7c74422623..50d8bc319c 100644
> > > --- a/drivers/usb/musb/musb_udc.c
> > > +++ b/drivers/usb/musb/musb_udc.c
> > > @@ -707,9 +707,7 @@ static void musb_peri_rx(u16 intr)
> > >  {
> > >  	unsigned int ep;
> > >  
> > > -	/* Check for EP0 */
> > > -	if (0x01 & intr)
> > > -		musb_peri_ep0();
> > > +	/* First bit is reserved and does not indicate interrupt
> > > for EP0 */ 
> > >  	for (ep = 1; ep < 16; ep++) {
> > >  		if ((1 << ep) & intr)
> > > @@ -721,9 +719,9 @@ static void musb_peri_tx(u16 intr)
> > >  {
> > >  	unsigned int ep;
> > >  
> > > -	/* Check for EP0 */
> > > +	/* Check for EP0: first bit indicates interrupt for both
> > > RX and TX */ if (0x01 & intr)
> > > -		musb_peri_ep0_tx();
> > > +		musb_peri_ep0();
> > >  
> > >  	for (ep = 1; ep < 16; ep++) {
> > >  		if ((1 << ep) & intr)
> > > @@ -750,8 +748,6 @@ void udc_irq(void)
> > >  			musb_peri_resume();
> > >  		}
> > >  
> > > -		musb_peri_ep0();
> > > -
> > >  		if (MUSB_INTR_RESET & intrusb) {
> > >  			usbd_device_event_irq(udc_device,
> > > DEVICE_RESET, 0); musb_peri_reset();
> > > @@ -790,7 +786,7 @@ void udc_irq(void)
> > >  			if (intrtx)
> > >  				musb_peri_tx(intrtx);
> > >  		} else {
> > > -			if (MUSB_INTR_SOF & intrusb) {
> > > +			if (readw(&musbr->intrtx) & 0x1) {
> > >  				u8 faddr;
> > >  				faddr = readb(&musbr->faddr);
> > >  				/*  
> > 
> > Applying this patch causes error. Could you rebase your work on
> > newest master (after onging PR is accepted).  
> 
> Hello! This patch series is rebased on top of the another patch series
> "Nokia RX-51: Fix USB TTY console and enable it" as it depends on it.

I took this patch series as they were queued in patchwork.

> So I cannot rebase it on top of master as it would not work.
> 
> Nokia RX-51: Fix USB TTY console and enable it:
> <20201129164618.5829-1-pali at kernel.org>
> https://lists.denx.de/pipermail/u-boot/2020-November/433728.html

Those were delegated to Marek, and are not yet in his tree
(-master/-next).

Ok. I will wait for them to be pulled.

> 
> > Thanks in advance and sorry for delay.
> > 
> > 
> > Best regards,
> > 
> > Lukasz Majewski
> > 
> > --
> > 
> > DENX Software Engineering GmbH,      Managing Director: Wolfgang
> > Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell,
> > Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> > lukma at denx.de  
> 
> 




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210123/9eec2fc9/attachment.sig>