[PATCH v5 15/20] arm: dts: k3-j7200-common-proc-board: Enable support for UHS modes

[Aswath Govindraju]

From: Faiz Abbas <faiz_abbas at ti.com>

Add support for UHS modes by adding the regulators to power cycle
and voltage switch the card. Also add pinmuxes required for each
node

Signed-off-by: Faiz Abbas <faiz_abbas at ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
---
 arch/arm/dts/k3-j7200-common-proc-board.dts   | 49 ++++++++++++++++++-
 arch/arm/dts/k3-j7200-main.dtsi               |  1 +
 .../arm/dts/k3-j7200-r5-common-proc-board.dts | 15 ++++++
 3 files changed, 63 insertions(+), 2 deletions(-)

diff --git a/arch/arm/dts/k3-j7200-common-proc-board.dts b/arch/arm/dts/k3-j7200-common-proc-board.dts
index cc3d933cbb51..85cb159838e3 100644
--- a/arch/arm/dts/k3-j7200-common-proc-board.dts
+++ b/arch/arm/dts/k3-j7200-common-proc-board.dts
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/net/ti-dp83867.h>
 #include "k3-j7200-som-p0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	chosen {
@@ -20,6 +21,29 @@
 		remoteproc2 = &main_r5fss0_core0;
 		remoteproc3 = &main_r5fss0_core1;
 	};
+
+	vdd_mmc1: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd_sd_dv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0
+			  3300000 0x1>;
+	};
 };
 
 &wkup_pmx0 {
@@ -69,6 +93,25 @@
 		>;
 	};
 
+	main_mmc1_pins_default: main_mmc1_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
+			J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
+			J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+			J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
+			J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
+			J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
+			J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
+			J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+		>;
+	};
+
 	main_usbss0_pins_default: main_usbss0_pins_default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
@@ -140,10 +183,12 @@
 
 &main_sdhci1 {
 	/* SD card */
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
-	no-1-8-v;
-	sdhci-caps-mask = <0x8000000F 0x0>;
 };
 
 &main_i2c0 {
diff --git a/arch/arm/dts/k3-j7200-main.dtsi b/arch/arm/dts/k3-j7200-main.dtsi
index b722204c44ac..8150ff6332c2 100644
--- a/arch/arm/dts/k3-j7200-main.dtsi
+++ b/arch/arm/dts/k3-j7200-main.dtsi
@@ -253,6 +253,7 @@
 		ti,otap-del-sel-sdr50 = <0xc>;
 		ti,otap-del-sel-sdr104 = <0x5>;
 		ti,otap-del-sel-ddr50 = <0xc>;
+		ti,clkbuf-sel = <0x7>;
 		dma-coherent;
 	};
 
diff --git a/arch/arm/dts/k3-j7200-r5-common-proc-board.dts b/arch/arm/dts/k3-j7200-r5-common-proc-board.dts
index 2ac887b180c9..04914320609c 100644
--- a/arch/arm/dts/k3-j7200-r5-common-proc-board.dts
+++ b/arch/arm/dts/k3-j7200-r5-common-proc-board.dts
@@ -162,6 +162,19 @@
 		>;
 	};
 
+	main_mmc1_pins_default: main_mmc1_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
+			J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
+			J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+			J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
+			J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
+			J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
+			J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
+			J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
+
 	main_usbss0_pins_default: main_usbss0_pins_default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
@@ -198,6 +211,8 @@
 	/delete-property/ power-domains;
 	/delete-property/ assigned-clocks;
 	/delete-property/ assigned-clock-parents;
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
 	clock-names = "clk_xin";
 	clocks = <&clk_200mhz>;
 	ti,driver-strength-ohm = <50>;
-- 
2.17.1