[PATCH] xilinx: Sync DTs with Linux kernel
Michal Simek
michal.simek at xilinx.com
Wed Mar 10 14:10:56 CET 2021
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek at xilinx.com>
---
arch/arm/dts/zynq-zc702.dts | 2 +-
arch/arm/dts/zynq-zturn-common.dtsi | 2 +-
arch/arm/dts/zynq-zybo-z7.dts | 2 +-
arch/arm/dts/zynqmp-clk-ccf.dtsi | 16 +-
arch/arm/dts/zynqmp-g-a2197-00-revA.dts | 3 -
arch/arm/dts/zynqmp-m-a2197-01-revA.dts | 3 -
arch/arm/dts/zynqmp-zc1232-revA.dts | 2 -
arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts | 19 +--
arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts | 2 +-
arch/arm/dts/zynqmp-zcu100-revC.dts | 48 ++++--
arch/arm/dts/zynqmp-zcu102-revA.dts | 106 ++++++++++----
arch/arm/dts/zynqmp-zcu104-revA.dts | 44 +++++-
arch/arm/dts/zynqmp-zcu104-revC.dts | 44 +++++-
arch/arm/dts/zynqmp-zcu106-revA.dts | 96 ++++++++++--
arch/arm/dts/zynqmp-zcu111-revA.dts | 78 ++++++++--
arch/arm/dts/zynqmp-zcu208-revA.dts | 58 ++++++--
arch/arm/dts/zynqmp-zcu216-revA.dts | 58 ++++++--
arch/arm/dts/zynqmp.dtsi | 154 +++++---------------
include/dt-bindings/dma/xlnx-zynqmp-dpdma.h | 16 ++
19 files changed, 498 insertions(+), 255 deletions(-)
create mode 100644 include/dt-bindings/dma/xlnx-zynqmp-dpdma.h
diff --git a/arch/arm/dts/zynq-zc702.dts b/arch/arm/dts/zynq-zc702.dts
index b043d341d680..e45eba3d90b3 100644
--- a/arch/arm/dts/zynq-zc702.dts
+++ b/arch/arm/dts/zynq-zc702.dts
@@ -51,7 +51,7 @@
leds {
compatible = "gpio-leds";
- ds23 {
+ led-ds23 {
label = "ds23";
gpios = <&gpio0 10 0>;
linux,default-trigger = "heartbeat";
diff --git a/arch/arm/dts/zynq-zturn-common.dtsi b/arch/arm/dts/zynq-zturn-common.dtsi
index 1d7af02893dc..486b6fa2e1b8 100644
--- a/arch/arm/dts/zynq-zturn-common.dtsi
+++ b/arch/arm/dts/zynq-zturn-common.dtsi
@@ -112,7 +112,7 @@
};
accelerometer at 53 {
- compatible = "adi,adxl345", "adxl345", "adi,adxl34x", "adxl34x";
+ compatible = "adi,adxl345";
reg = <0x53>;
interrupt-parent = <&intc>;
interrupts = <0x0 0x1e 0x4>;
diff --git a/arch/arm/dts/zynq-zybo-z7.dts b/arch/arm/dts/zynq-zybo-z7.dts
index 3f8a3bfa0ff7..116958ec97aa 100644
--- a/arch/arm/dts/zynq-zybo-z7.dts
+++ b/arch/arm/dts/zynq-zybo-z7.dts
@@ -31,7 +31,7 @@
gpio-leds {
compatible = "gpio-leds";
- ld4 {
+ led-ld4 {
label = "zynq-zybo-z7:green:ld4";
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
};
diff --git a/arch/arm/dts/zynqmp-clk-ccf.dtsi b/arch/arm/dts/zynqmp-clk-ccf.dtsi
index b02ef22abd20..987792e5c511 100644
--- a/arch/arm/dts/zynqmp-clk-ccf.dtsi
+++ b/arch/arm/dts/zynqmp-clk-ccf.dtsi
@@ -284,18 +284,16 @@
clocks = <&zynqmp_clk AMS_REF>;
};
-&zynqmp_dpsub {
- clocks = <&dp_aclk>, <&zynqmp_clk DP_AUDIO_REF>, <&zynqmp_clk DP_VIDEO_REF>;
+&zynqmp_pcap {
+ clocks = <&zynqmp_clk PCAP>;
};
-&xlnx_dpdma {
+&zynqmp_dpdma {
clocks = <&zynqmp_clk DPDMA_REF>;
};
-&zynqmp_dp_snd_codec0 {
- clocks = <&zynqmp_clk DP_AUDIO_REF>;
-};
-
-&zynqmp_pcap {
- clocks = <&zynqmp_clk PCAP>;
+&zynqmp_dpsub {
+ clocks = <&zynqmp_clk TOPSW_LSBUS>,
+ <&zynqmp_clk DP_AUDIO_REF>,
+ <&zynqmp_clk DP_VIDEO_REF>;
};
diff --git a/arch/arm/dts/zynqmp-g-a2197-00-revA.dts b/arch/arm/dts/zynqmp-g-a2197-00-revA.dts
index 9468dc574fd8..f94b797d1a24 100644
--- a/arch/arm/dts/zynqmp-g-a2197-00-revA.dts
+++ b/arch/arm/dts/zynqmp-g-a2197-00-revA.dts
@@ -88,9 +88,6 @@
reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
/* xlnx,phy-type = <PHY_TYPE_SGMII>; */
};
-/* phy-names = "...";
- phys = <&lane0 PHY_TYPE_SGMII ... >
- Note: lane0 sgmii/lane1 usb3 */
};
&gpio {
diff --git a/arch/arm/dts/zynqmp-m-a2197-01-revA.dts b/arch/arm/dts/zynqmp-m-a2197-01-revA.dts
index 66ea02e5be7f..19e1ebdb1d6a 100644
--- a/arch/arm/dts/zynqmp-m-a2197-01-revA.dts
+++ b/arch/arm/dts/zynqmp-m-a2197-01-revA.dts
@@ -118,9 +118,6 @@
reg = <0>;
/* xlnx,phy-type = <PHY_TYPE_SGMII>; */
};
-/* phy-names = "...";
- phys = <&lane0 PHY_TYPE_SGMII ... >
- Note: lane0 sgmii/lane1 usb3 */
};
&gpio {
diff --git a/arch/arm/dts/zynqmp-zc1232-revA.dts b/arch/arm/dts/zynqmp-zc1232-revA.dts
index afb3e96520b8..ef7cf0a36b21 100644
--- a/arch/arm/dts/zynqmp-zc1232-revA.dts
+++ b/arch/arm/dts/zynqmp-zc1232-revA.dts
@@ -78,8 +78,6 @@
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
- phy-names = "sata-phy";
- phys = <&lane0 PHY_TYPE_SATA 0 0 125000000>, <&lane1 PHY_TYPE_SATA 1 1 125000000>;
};
&uart0 {
diff --git a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
index e2428ec974a3..b8c5efb6a914 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
@@ -175,26 +175,11 @@
dr_mode = "host";
};
-&zynqmp_dpsub {
- status = "okay";
-};
-
-&zynqmp_dp_snd_pcm0 {
- status = "okay";
-};
-
-&zynqmp_dp_snd_pcm1 {
+&zynqmp_dpdma {
status = "okay";
};
-&zynqmp_dp_snd_card0 {
- status = "okay";
-};
-
-&zynqmp_dp_snd_codec0 {
+&zynqmp_dpsub {
status = "okay";
};
-&xlnx_dpdma {
- status = "okay";
-};
diff --git a/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts b/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts
index 9b38b8b919e2..aadda179c323 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts
@@ -119,7 +119,7 @@
status = "okay";
};
-&xlnx_dpdma {
+&zynqmp_dpdma {
status = "okay";
};
diff --git a/arch/arm/dts/zynqmp-zcu100-revC.dts b/arch/arm/dts/zynqmp-zcu100-revC.dts
index d6c914c917f5..bbcc69c79673 100644
--- a/arch/arm/dts/zynqmp-zcu100-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu100-revC.dts
@@ -69,27 +69,27 @@
leds {
compatible = "gpio-leds";
- ds2 {
+ led-ds2 {
label = "ds2";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- ds3 {
+ led-ds3 {
label = "ds3";
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx"; /* WLAN tx */
default-state = "off";
};
- ds4 {
+ led-ds4 {
label = "ds4";
gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0rx"; /* WLAN rx */
default-state = "off";
};
- ds5 {
+ led-ds5 {
label = "ds5";
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
@@ -130,6 +130,18 @@
compatible = "iio-hwmon";
io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
};
+
+ si5335a_0: clk26 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+
+ si5335a_1: clk27 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
};
&dcc {
@@ -212,7 +224,7 @@
compatible = "ti,tps65086";
reg = <0x5e>;
interrupt-parent = <&gpio>;
- interrupts = <77 GPIO_ACTIVE_LOW>;
+ interrupts = <77 IRQ_TYPE_LEVEL_LOW>;
#gpio-cells = <2>;
gpio-controller;
};
@@ -250,6 +262,13 @@
};
};
+&psgtr {
+ status = "okay";
+ /* usb3, dps */
+ clocks = <&si5335a_0>, <&si5335a_1>;
+ clock-names = "ref0", "ref1";
+};
+
&rtc {
status = "okay";
};
@@ -281,10 +300,6 @@
};
};
-&serdes {
- status = "okay";
-};
-
&spi0 { /* Low Speed connector */
status = "okay";
label = "LS-SPI0";
@@ -318,8 +333,6 @@
&dwc3_0 {
status = "okay";
dr_mode = "peripheral";
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 0 26000000>;
maximum-speed = "super-speed";
};
@@ -331,8 +344,6 @@
&dwc3_1 {
status = "okay";
dr_mode = "host";
- phy-names = "usb3-phy";
- phys = <&lane3 PHY_TYPE_USB3 1 0 26000000>;
maximum-speed = "super-speed";
};
@@ -347,3 +358,14 @@
&ams_ps {
status = "okay";
};
+
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 1>,
+ <&psgtr 0 PHY_TYPE_DP 1 1>;
+};
diff --git a/arch/arm/dts/zynqmp-zcu102-revA.dts b/arch/arm/dts/zynqmp-zcu102-revA.dts
index ed036e68f5e3..9323b8d64d56 100644
--- a/arch/arm/dts/zynqmp-zcu102-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu102-revA.dts
@@ -137,6 +137,19 @@
compatible = "iio-hwmon";
io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>;
};
+
+ /* 48MHz reference crystal */
+ ref48: ref48M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+
+ refhdmi: refhdmi {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <114285000>;
+ };
};
&can1 {
@@ -213,25 +226,25 @@
gpio-line-names = "PS_GTR_LAN_SEL0", "PS_GTR_LAN_SEL1", "PS_GTR_LAN_SEL2", "PS_GTR_LAN_SEL3",
"PCI_CLK_DIR_SEL", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B",
"", "", "", "", "", "", "", "", "";
- gtr-sel0 {
+ gtr-sel0-hog {
gpio-hog;
gpios = <0 0>;
output-low; /* PCIE = 0, DP = 1 */
line-name = "sel0";
};
- gtr-sel1 {
+ gtr-sel1-hog {
gpio-hog;
gpios = <1 0>;
output-high; /* PCIE = 0, DP = 1 */
line-name = "sel1";
};
- gtr-sel2 {
+ gtr-sel2-hog {
gpio-hog;
gpios = <2 0>;
output-high; /* PCIE = 0, USB0 = 1 */
line-name = "sel2";
};
- gtr-sel3 {
+ gtr-sel3-hog {
gpio-hog;
gpios = <3 0>;
output-high; /* PCIE = 0, SATA = 1 */
@@ -494,8 +507,54 @@
si5341: clock-generator at 36 { /* SI5341 - u69 */
compatible = "silabs,si5341";
reg = <0x36>;
+ #clock-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&ref48>;
+ clock-names = "xtal";
+ clock-output-names = "si5341";
+
+ si5341_0: out at 0 {
+ /* refclk0 for PS-GT, used for DP */
+ reg = <0>;
+ always-on;
+ };
+ si5341_2: out at 2 {
+ /* refclk2 for PS-GT, used for USB3 */
+ reg = <2>;
+ always-on;
+ };
+ si5341_3: out at 3 {
+ /* refclk3 for PS-GT, used for SATA */
+ reg = <3>;
+ always-on;
+ };
+ si5341_4: out at 4 {
+ /* refclk4 for PS-GT, used for PCIE slot */
+ reg = <4>;
+ always-on;
+ };
+ si5341_5: out at 5 {
+ /* refclk5 for PS-GT, used for PCIE */
+ reg = <5>;
+ always-on;
+ };
+ si5341_6: out at 6 {
+ /* refclk6 PL CLK125 */
+ reg = <6>;
+ always-on;
+ };
+ si5341_7: out at 7 {
+ /* refclk7 PL CLK74 */
+ reg = <7>;
+ always-on;
+ };
+ si5341_9: out at 9 {
+ /* refclk9 used for PS_REF_CLK 33.3 MHz */
+ reg = <9>;
+ always-on;
+ };
};
-
};
i2c at 2 {
#address-cells = <1>;
@@ -603,6 +662,13 @@
status = "okay";
};
+&psgtr {
+ status = "okay";
+ /* pcie, sata, usb3, dp */
+ clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+ clock-names = "ref0", "ref1", "ref2", "ref3";
+};
+
&qspi {
status = "okay";
is-dual = <1>;
@@ -649,7 +715,7 @@
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
@@ -663,10 +729,6 @@
xlnx,mio-bank = <1>;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -684,8 +746,6 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
maximum-speed = "super-speed";
};
@@ -705,26 +765,12 @@
status = "okay";
};
-&zynqmp_dpsub {
+&zynqmp_dpdma {
status = "okay";
};
-&zynqmp_dp_snd_codec0 {
- status = "okay";
-};
-
-&zynqmp_dp_snd_pcm0 {
- status = "okay";
-};
-
-&zynqmp_dp_snd_pcm1 {
- status = "okay";
-};
-
-&zynqmp_dp_snd_card0 {
- status = "okay";
-};
-
-&xlnx_dpdma {
+&zynqmp_dpsub {
status = "okay";
+ phy-names = "dp-phy0";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 3>;
};
diff --git a/arch/arm/dts/zynqmp-zcu104-revA.dts b/arch/arm/dts/zynqmp-zcu104-revA.dts
index cb8ffdff9771..a95bd4922a62 100644
--- a/arch/arm/dts/zynqmp-zcu104-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu104-revA.dts
@@ -40,6 +40,24 @@
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
+
+ clock_8t49n287_5: clk125 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ clock_8t49n287_2: clk26 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+
+ clock_8t49n287_3: clk27 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
};
&can1 {
@@ -226,6 +244,13 @@
};
};
+&psgtr {
+ status = "okay";
+ /* nc, sata, usb3, dp */
+ clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&rtc {
status = "okay";
};
@@ -242,7 +267,7 @@
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
@@ -253,10 +278,6 @@
disable-wp;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -274,8 +295,6 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
maximum-speed = "super-speed";
};
@@ -294,3 +313,14 @@
&ams_pl {
status = "okay";
};
+
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
+ <&psgtr 0 PHY_TYPE_DP 1 3>;
+};
diff --git a/arch/arm/dts/zynqmp-zcu104-revC.dts b/arch/arm/dts/zynqmp-zcu104-revC.dts
index e203280f0eca..8f30a2883e27 100644
--- a/arch/arm/dts/zynqmp-zcu104-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu104-revC.dts
@@ -46,6 +46,24 @@
compatible = "iio-hwmon";
io-channels = <&u183 0>, <&u183 1>, <&u183 2>, <&u183 3>;
};
+
+ clock_8t49n287_5: clk125 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ clock_8t49n287_2: clk26 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+
+ clock_8t49n287_3: clk27 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
};
&can1 {
@@ -243,6 +261,13 @@
status = "okay";
};
+&psgtr {
+ status = "okay";
+ /* nc, sata, usb3, dp */
+ clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&sata {
status = "okay";
/* SATA OOB timing settings */
@@ -255,7 +280,7 @@
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
@@ -266,10 +291,6 @@
disable-wp;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -287,8 +308,6 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
maximum-speed = "super-speed";
};
@@ -307,3 +326,14 @@
&ams_pl {
status = "okay";
};
+
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
+ <&psgtr 0 PHY_TYPE_DP 1 3>;
+};
diff --git a/arch/arm/dts/zynqmp-zcu106-revA.dts b/arch/arm/dts/zynqmp-zcu106-revA.dts
index 1dff845ceeb6..971f76f1cabe 100644
--- a/arch/arm/dts/zynqmp-zcu106-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu106-revA.dts
@@ -137,6 +137,19 @@
compatible = "iio-hwmon";
io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>;
};
+
+ /* 48MHz reference crystal */
+ ref48: ref48M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+
+ refhdmi: refhdmi {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <114285000>;
+ };
};
&can1 {
@@ -147,6 +160,18 @@
status = "okay";
};
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
+ <&psgtr 0 PHY_TYPE_DP 1 3>;
+};
+
+/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
@@ -490,8 +515,45 @@
#size-cells = <0>;
reg = <1>;
si5341: clock-generator at 36 { /* SI5341 - u69 */
- compatible = "si5341";
+ compatible = "silabs,si5341";
reg = <0x36>;
+ #clock-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&ref48>;
+ clock-names = "xtal";
+ clock-output-names = "si5341";
+
+ si5341_0: out at 0 {
+ /* refclk0 for PS-GT, used for DP */
+ reg = <0>;
+ always-on;
+ };
+ si5341_2: out at 2 {
+ /* refclk2 for PS-GT, used for USB3 */
+ reg = <2>;
+ always-on;
+ };
+ si5341_3: out at 3 {
+ /* refclk3 for PS-GT, used for SATA */
+ reg = <3>;
+ always-on;
+ };
+ si5341_6: out at 6 {
+ /* refclk6 PL CLK125 */
+ reg = <6>;
+ always-on;
+ };
+ si5341_7: out at 7 {
+ /* refclk7 PL CLK74 */
+ reg = <7>;
+ always-on;
+ };
+ si5341_9: out at 9 {
+ /* refclk9 used for PS_REF_CLK 33.3 MHz */
+ reg = <9>;
+ always-on;
+ };
};
};
@@ -528,8 +590,23 @@
#size-cells = <0>;
reg = <4>;
si5328: clock-generator at 69 {/* SI5328 - u20 */
- compatible = "silabs,si5328";
reg = <0x69>;
+ /*
+ * Chip has interrupt present connected to PL
+ * interrupt-parent = <&>;
+ * interrupts = <>;
+ */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+ clocks = <&refhdmi>;
+ clock-names = "xtal";
+ clock-output-names = "si5328";
+
+ si5328_clk: clk0 at 0 {
+ reg = <0>;
+ clock-frequency = <27000000>;
+ };
};
};
i2c at 5 {
@@ -601,6 +678,13 @@
};
};
+&psgtr {
+ status = "okay";
+ /* nc, sata, usb3, dp */
+ clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&qspi {
status = "okay";
is-dual = <1>;
@@ -647,7 +731,7 @@
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
@@ -660,10 +744,6 @@
xlnx,mio-bank = <1>;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -681,8 +761,6 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
};
&watchdog0 {
diff --git a/arch/arm/dts/zynqmp-zcu111-revA.dts b/arch/arm/dts/zynqmp-zcu111-revA.dts
index 82e6c8d3cdfd..9e47008542ae 100644
--- a/arch/arm/dts/zynqmp-zcu111-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu111-revA.dts
@@ -121,6 +121,13 @@
compatible = "iio-hwmon";
io-channels = <&u79 0>, <&u79 1>, <&u79 2>, <&u79 3>;
};
+
+ /* 48MHz reference crystal */
+ ref48: ref48M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
};
&dcc {
@@ -386,10 +393,46 @@
#size-cells = <0>;
reg = <1>;
si5341: clock-generator at 36 { /* SI5341 - u46 */
- compatible = "si5341";
+ compatible = "silabs,si5341";
reg = <0x36>;
+ #clock-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&ref48>;
+ clock-names = "xtal";
+ clock-output-names = "si5341";
+
+ si5341_0: out at 0 {
+ /* refclk0 for PS-GT, used for DP */
+ reg = <0>;
+ always-on;
+ };
+ si5341_2: out at 2 {
+ /* refclk2 for PS-GT, used for USB3 */
+ reg = <2>;
+ always-on;
+ };
+ si5341_3: out at 3 {
+ /* refclk3 for PS-GT, used for SATA */
+ reg = <3>;
+ always-on;
+ };
+ si5341_5: out at 5 {
+ /* refclk5 PL CLK100 */
+ reg = <5>;
+ always-on;
+ };
+ si5341_6: out at 6 {
+ /* refclk6 PL CLK125 */
+ reg = <6>;
+ always-on;
+ };
+ si5341_9: out at 9 {
+ /* refclk9 used for PS_REF_CLK 33.3 MHz */
+ reg = <9>;
+ always-on;
+ };
};
-
};
i2c at 2 {
#address-cells = <1>;
@@ -423,8 +466,8 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
- si5328: clock-generator at 69 { /* SI5328 - u48 */
- compatible = "silabs,si5328";
+ si5382: clock-generator at 69 { /* SI5382 - u48 */
+ compatible = "silabs,si5382";
reg = <0x69>;
};
};
@@ -511,6 +554,13 @@
};
};
+&psgtr {
+ status = "okay";
+ /* nc, sata, usb3, dp */
+ clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&qspi {
status = "okay";
is-dual = <1>;
@@ -557,7 +607,7 @@
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
@@ -571,10 +621,6 @@
xlnx,mio-bank = <1>;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -582,12 +628,16 @@
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ dr_mode = "host";
};
-&dwc3_0 {
+&zynqmp_dpdma {
status = "okay";
- dr_mode = "host";
- snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 1>,
+ <&psgtr 0 PHY_TYPE_DP 1 1>;
};
diff --git a/arch/arm/dts/zynqmp-zcu208-revA.dts b/arch/arm/dts/zynqmp-zcu208-revA.dts
index 268e368b7657..0e114cdacb1a 100644
--- a/arch/arm/dts/zynqmp-zcu208-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu208-revA.dts
@@ -120,6 +120,13 @@
compatible = "iio-hwmon";
io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
};
+
+ /* 48MHz reference crystal */
+ ref48: ref48M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
};
&dcc {
@@ -404,10 +411,41 @@
#size-cells = <0>;
reg = <1>;
si5341: clock-generator at 36 { /* SI5341 - u43 */
- compatible = "si5341";
+ compatible = "silabs,si5341";
reg = <0x36>;
+ #clock-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&ref48>;
+ clock-names = "xtal";
+ clock-output-names = "si5341";
+
+ si5341_2: out at 2 {
+ /* refclk2 for PS-GT, used for USB3 */
+ reg = <2>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_3: out at 3 {
+ /* refclk3 for PS-GT, used for SATA */
+ reg = <3>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_5: out at 5 {
+ /* refclk5 PL CLK100 */
+ reg = <5>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_6: out at 6 {
+ /* refclk6 PL CLK125 */
+ reg = <6>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_9: out at 9 {
+ /* refclk9 used for PS_REF_CLK 33.3 MHz */
+ reg = <9>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
};
-
};
i2c_si570_user_c0: i2c at 2 {
#address-cells = <1>;
@@ -541,6 +579,13 @@
};
};
+&psgtr {
+ status = "okay";
+ /* pcie, sata, usb3, dp */
+ clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+ clock-names = "ref0", "ref1", "ref2", "ref3";
+};
+
&rtc {
status = "okay";
};
@@ -556,8 +601,7 @@
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
- phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
};
/* SD1 with level shifter */
@@ -571,10 +615,6 @@
xlnx,mio-bank = <1>;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -588,6 +628,4 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
};
diff --git a/arch/arm/dts/zynqmp-zcu216-revA.dts b/arch/arm/dts/zynqmp-zcu216-revA.dts
index 847e689c155f..2302b07c4825 100644
--- a/arch/arm/dts/zynqmp-zcu216-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu216-revA.dts
@@ -120,6 +120,20 @@
compatible = "iio-hwmon";
io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
};
+
+ /* 48MHz reference crystal */
+ ref48: ref48M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+};
+
+&psgtr {
+ status = "okay";
+ /* pcie, sata, usb3, dp */
+ clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+ clock-names = "ref0", "ref1", "ref2", "ref3";
};
&dcc {
@@ -408,10 +422,41 @@
#size-cells = <0>;
reg = <1>;
si5341: clock-generator at 36 { /* SI5341 - u43 */
- compatible = "si5341";
+ compatible = "silabs,si5341";
reg = <0x36>;
+ #clock-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&ref48>;
+ clock-names = "xtal";
+ clock-output-names = "si5341";
+
+ si5341_2: out at 2 {
+ /* refclk2 for PS-GT, used for USB3 */
+ reg = <2>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_3: out at 3 {
+ /* refclk3 for PS-GT, used for SATA */
+ reg = <3>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_5: out at 5 {
+ /* refclk5 PL CLK100 */
+ reg = <5>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_6: out at 6 {
+ /* refclk6 PL CLK125 */
+ reg = <6>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
+ si5341_9: out at 9 {
+ /* refclk9 used for PS_REF_CLK 33.3 MHz */
+ reg = <9>;
+ always-on; /* assigned-clocks does not enable, so do it here */
+ };
};
-
};
i2c_si570_user_c0: i2c at 2 {
#address-cells = <1>;
@@ -560,8 +605,7 @@
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
- phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
};
/* SD1 with level shifter */
@@ -575,10 +619,6 @@
xlnx,mio-bank = <1>;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -592,6 +632,4 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
};
diff --git a/arch/arm/dts/zynqmp.dtsi b/arch/arm/dts/zynqmp.dtsi
index 2917a956eb3d..84d9770225aa 100644
--- a/arch/arm/dts/zynqmp.dtsi
+++ b/arch/arm/dts/zynqmp.dtsi
@@ -12,6 +12,7 @@
* the License, or (at your option) any later version.
*/
+#include <dt-bindings/dma/xlnx-zynqmp-dpdma.h>
#include <dt-bindings/power/xlnx-zynqmp-power.h>
#include <dt-bindings/reset/xlnx-zynqmp-resets.h>
@@ -160,11 +161,25 @@
mbox-names = "tx", "rx";
};
+ nvmem_firmware {
+ compatible = "xlnx,zynqmp-nvmem-fw";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ soc_revision: soc_revision at 0 {
+ reg = <0x0 0x4>;
+ };
+ };
+
zynqmp_pcap: pcap {
compatible = "xlnx,zynqmp-pcap-fpga";
clock-names = "ref_clk";
};
+ xlnx_aes: zynqmp-aes {
+ compatible = "xlnx,zynqmp-aes";
+ };
+
zynqmp_reset: reset-controller {
compatible = "xlnx,zynqmp-reset";
#reset-cells = <1>;
@@ -198,16 +213,6 @@
ranges;
};
- nvmem_firmware {
- compatible = "xlnx,zynqmp-nvmem-fw";
- #address-cells = <1>;
- #size-cells = <1>;
-
- soc_revision: soc_revision at 0 {
- reg = <0x0 0x4>;
- };
- };
-
amba: axi {
compatible = "simple-bus";
u-boot,dm-pre-reloc;
@@ -501,8 +506,8 @@
interrupts = <0 112 4>;
};
- nand0: nand at ff100000 {
- compatible = "arasan,nfc-v3p10";
+ nand0: nand-controller at ff100000 {
+ compatible = "xlnx,zynqmp-nand-controller", "arasan,nfc-v3p10";
status = "disabled";
reg = <0x0 0xff100000 0x0 0x1000>;
clock-names = "controller", "bus";
@@ -667,6 +672,15 @@
power-domains = <&zynqmp_firmware PD_QSPI>;
};
+ psgtr: phy at fd400000 {
+ compatible = "xlnx,zynqmp-psgtr-v1.1";
+ status = "disabled";
+ reg = <0x0 0xfd400000 0x0 0x40000>,
+ <0x0 0xfd3d0000 0x0 0x1000>;
+ reg-names = "serdes", "siou";
+ #phy-cells = <4>;
+ };
+
rtc: rtc at ffa60000 {
compatible = "xlnx,zynqmp-rtc";
status = "disabled";
@@ -677,45 +691,6 @@
calibration = <0x8000>;
};
- serdes: zynqmp_phy at fd400000 {
- compatible = "xlnx,zynqmp-psgtr";
- status = "disabled";
- reg = <0x0 0xfd400000 0x0 0x40000>,
- <0x0 0xfd3d0000 0x0 0x1000>,
- <0x0 0xff5e0000 0x0 0x1000>;
- reg-names = "serdes", "siou", "lpd";
- nvmem-cells = <&soc_revision>;
- nvmem-cell-names = "soc_revision";
- resets = <&zynqmp_reset ZYNQMP_RESET_SATA>,
- <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
- <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
- <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
- <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
- <&zynqmp_reset ZYNQMP_RESET_USB0_APB>,
- <&zynqmp_reset ZYNQMP_RESET_USB1_APB>,
- <&zynqmp_reset ZYNQMP_RESET_DP>,
- <&zynqmp_reset ZYNQMP_RESET_GEM0>,
- <&zynqmp_reset ZYNQMP_RESET_GEM1>,
- <&zynqmp_reset ZYNQMP_RESET_GEM2>,
- <&zynqmp_reset ZYNQMP_RESET_GEM3>;
- reset-names = "sata_rst", "usb0_crst", "usb1_crst",
- "usb0_hibrst", "usb1_hibrst", "usb0_apbrst",
- "usb1_apbrst", "dp_rst", "gem0_rst",
- "gem1_rst", "gem2_rst", "gem3_rst";
- lane0: lane0 {
- #phy-cells = <4>;
- };
- lane1: lane1 {
- #phy-cells = <4>;
- };
- lane2: lane2 {
- #phy-cells = <4>;
- };
- lane3: lane3 {
- #phy-cells = <4>;
- };
- };
-
sata: ahci at fd0c0000 {
compatible = "ceva,ahci-1v84";
status = "disabled";
@@ -740,11 +715,11 @@
xlnx,device_id = <0>;
#stream-id-cells = <1>;
iommus = <&smmu 0x870>;
- power-domains = <&zynqmp_firmware PD_SD_0>;
nvmem-cells = <&soc_revision>;
nvmem-cell-names = "soc_revision";
#clock-cells = <1>;
clock-output-names = "clk_out_sd0", "clk_in_sd0";
+ power-domains = <&zynqmp_firmware PD_SD_0>;
};
sdhci1: mmc at ff170000 {
@@ -758,11 +733,11 @@
xlnx,device_id = <1>;
#stream-id-cells = <1>;
iommus = <&smmu 0x871>;
- power-domains = <&zynqmp_firmware PD_SD_1>;
nvmem-cells = <&soc_revision>;
nvmem-cell-names = "soc_revision";
#clock-cells = <1>;
clock-output-names = "clk_out_sd1", "clk_in_sd1";
+ power-domains = <&zynqmp_firmware PD_SD_1>;
};
smmu: iommu at fd800000 {
@@ -962,37 +937,18 @@
};
};
- xlnx_dpdma: dma at fd4c0000 {
- compatible = "xlnx,dpdma";
+ zynqmp_dpdma: dma-controller at fd4c0000 {
+ compatible = "xlnx,zynqmp-dpdma";
status = "disabled";
reg = <0x0 0xfd4c0000 0x0 0x1000>;
interrupts = <0 122 4>;
interrupt-parent = <&gic>;
clock-names = "axi_clk";
power-domains = <&zynqmp_firmware PD_DP>;
- dma-channels = <6>;
#dma-cells = <1>;
- dma-video0channel {
- compatible = "xlnx,video0";
- };
- dma-video1channel {
- compatible = "xlnx,video1";
- };
- dma-video2channel {
- compatible = "xlnx,video2";
- };
- dma-graphicschannel {
- compatible = "xlnx,graphics";
- };
- dma-audio0channel {
- compatible = "xlnx,audio0";
- };
- dma-audio1channel {
- compatible = "xlnx,audio1";
- };
};
- zynqmp_dpsub: zynqmp-display at fd4a0000 {
+ zynqmp_dpsub: display at fd4a0000 {
compatible = "xlnx,zynqmp-dpsub-1.7";
status = "disabled";
reg = <0x0 0xfd4a0000 0x0 0x1000>,
@@ -1002,51 +958,15 @@
reg-names = "dp", "blend", "av_buf", "aud";
interrupts = <0 119 4>;
interrupt-parent = <&gic>;
-
clock-names = "dp_apb_clk", "dp_aud_clk",
"dp_vtc_pixel_clk_in";
-
power-domains = <&zynqmp_firmware PD_DP>;
-
- vid-layer {
- dma-names = "vid0", "vid1", "vid2";
- dmas = <&xlnx_dpdma 0>,
- <&xlnx_dpdma 1>,
- <&xlnx_dpdma 2>;
- };
-
- gfx-layer {
- dma-names = "gfx0";
- dmas = <&xlnx_dpdma 3>;
- };
-
- /* dummy node to indicate there's no child i2c device */
- i2c-bus {
- };
-
- zynqmp_dp_snd_codec0: zynqmp_dp_snd_codec0 {
- compatible = "xlnx,dp-snd-codec";
- clock-names = "aud_clk";
- };
-
- zynqmp_dp_snd_pcm0: zynqmp_dp_snd_pcm0 {
- compatible = "xlnx,dp-snd-pcm";
- dmas = <&xlnx_dpdma 4>;
- dma-names = "tx";
- };
-
- zynqmp_dp_snd_pcm1: zynqmp_dp_snd_pcm1 {
- compatible = "xlnx,dp-snd-pcm";
- dmas = <&xlnx_dpdma 5>;
- dma-names = "tx";
- };
-
- zynqmp_dp_snd_card0: zynqmp_dp_snd_card {
- compatible = "xlnx,dp-snd-card";
- xlnx,dp-snd-pcm = <&zynqmp_dp_snd_pcm0>,
- <&zynqmp_dp_snd_pcm1>;
- xlnx,dp-snd-codec = <&zynqmp_dp_snd_codec0>;
- };
+ resets = <&zynqmp_reset ZYNQMP_RESET_DP>;
+ dma-names = "vid0", "vid1", "vid2", "gfx0";
+ dmas = <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO0>,
+ <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO1>,
+ <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO2>,
+ <&zynqmp_dpdma ZYNQMP_DPDMA_GRAPHICS>;
};
};
};
diff --git a/include/dt-bindings/dma/xlnx-zynqmp-dpdma.h b/include/dt-bindings/dma/xlnx-zynqmp-dpdma.h
new file mode 100644
index 000000000000..3719cda5679d
--- /dev/null
+++ b/include/dt-bindings/dma/xlnx-zynqmp-dpdma.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/*
+ * Copyright 2019 Laurent Pinchart <laurent.pinchart at ideasonboard.com>
+ */
+
+#ifndef __DT_BINDINGS_DMA_XLNX_ZYNQMP_DPDMA_H__
+#define __DT_BINDINGS_DMA_XLNX_ZYNQMP_DPDMA_H__
+
+#define ZYNQMP_DPDMA_VIDEO0 0
+#define ZYNQMP_DPDMA_VIDEO1 1
+#define ZYNQMP_DPDMA_VIDEO2 2
+#define ZYNQMP_DPDMA_GRAPHICS 3
+#define ZYNQMP_DPDMA_AUDIO0 4
+#define ZYNQMP_DPDMA_AUDIO1 5
+
+#endif /* __DT_BINDINGS_DMA_XLNX_ZYNQMP_DPDMA_H__ */
--
2.30.1
More information about the U-Boot
mailing list