[PATCH v1 5/6] net: mv88e61xx: Set proper offset when R0_LED/ADDR4 is set on bootstrap

[Lukasz Majewski]

The mv88e61xx driver need to be adjusted to handle situation when
switch MDIO addresses are switched by offset (0x10 in this case).

Signed-off-by: Lukasz Majewski <lukma at denx.de>
---

 drivers/net/phy/mv88e61xx.c | 25 ++++++++++++++++++-------
 1 file changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
index 3d846b89fd12..325d5b56135f 100644
--- a/drivers/net/phy/mv88e61xx.c
+++ b/drivers/net/phy/mv88e61xx.c
@@ -45,7 +45,6 @@
 #define PORT_MASK(port_count)		((1 << (port_count)) - 1)
 
 /* Device addresses */
-#define DEVADDR_PHY(p)			(p)
 #define DEVADDR_SERDES			0x0F
 
 /* SMI indirection registers for multichip addressing mode */
@@ -414,7 +413,7 @@ static int mv88e61xx_phy_write_indirect(struct mii_dev *smi_wrapper, int dev,
 /* Wrapper function to make calls to phy_read_indirect simpler */
 static int mv88e61xx_phy_read(struct phy_device *phydev, int phy, int reg)
 {
-	return mv88e61xx_phy_read_indirect(phydev->bus, DEVADDR_PHY(phy),
+	return mv88e61xx_phy_read_indirect(phydev->bus, phydev->addr,
 					   MDIO_DEVAD_NONE, reg);
 }
 
@@ -422,7 +421,7 @@ static int mv88e61xx_phy_read(struct phy_device *phydev, int phy, int reg)
 static int mv88e61xx_phy_write(struct phy_device *phydev, int phy,
 		int reg, u16 val)
 {
-	return mv88e61xx_phy_write_indirect(phydev->bus, DEVADDR_PHY(phy),
+	return mv88e61xx_phy_write_indirect(phydev->bus, phydev->addr,
 					    MDIO_DEVAD_NONE, reg, val);
 }
 
@@ -926,12 +925,21 @@ static int mv88e61xx_priv_reg_offs_pre_init(struct phy_device *phydev)
 	/*
 	 * Now try via port registers with device address 0x08
 	 * (88E6020 and compatible switches).
+	 *
+	 * When R0_LED/ADDR4 is set during bootstrap, one needs
+	 * to add 0x10 offset to switch addresses.
+	 *
+	 * The phydev->addr is set according to device tree address
+	 * of MDIO accessible device:
+	 *
+	 * When on board RO_LED/ADDR4 = 1 -> 0x10
+	 *                              0 -> 0x0
 	 */
-	priv->port_reg_base = 0x08;
+	priv->port_reg_base = 0x08 + phydev->addr;
 	priv->id = mv88e61xx_get_switch_id(phydev);
 	if (priv->id != 0xfff0) {
-		priv->global1 = 0x0F;
-		priv->global2 = 0x07;
+		priv->global1 = 0x0F + phydev->addr;
+		priv->global2 = 0x07 + phydev->addr;
 		return 0;
 	}
 
@@ -1090,7 +1098,10 @@ static int mv88e61xx_phy_config(struct phy_device *phydev)
 
 	for (i = 0; i < priv->port_count; i++) {
 		if ((1 << i) & CONFIG_MV88E61XX_PHY_PORTS) {
-			phydev->addr = i;
+			if (phydev->addr)
+				phydev->addr += i;
+			else
+				phydev->addr = i;
 
 			res = mv88e61xx_phy_enable(phydev, i);
 			if (res < 0) {
-- 
2.20.1