[PATCH v9 00/28] mtd: spi-nor-core: add xSPI Octal DTR support

Pratyush Yadav p.yadav at ti.com
Wed May 5 11:41:10 CEST 2021


Hi,

This series adds support for octal DTR flashes in the SPI NOR framework,
and then adds hooks for the Cypress S28HS512T and Micron MT35XU512ABA
flashes.

The Cadence QSPI controller driver is also updated to run in Octal DTR
mode.

Tested on TI J721E for MT35XU512ABA and J7200 for S28HS512T. Also tested
on MT25QU512A for regressions.

Changes in v9:
- Fix a typo in patch 26 commit message.

- Add Sean's Reviewed-by in patch 3.

- Drop the 2-byte check from spi_mem_dtr_supports_op(). Instead, perform
  a even-byte length check on all 4 phases. Only do this when the
  buswidth of the phase is 8.

- Make template ops in spi_nor_check_readop() and spi_nor_check_pp()
  have 2-byte data phase so they don't get rejected when 8D-8D-8D
  protocol is being used.

Changes in v8:
- Rebase on latest master, fixing merge conflicts.

- Fix a regression related to address width that was discovered on
  Linux.

- Port spi_mem_dtr_supports_op() from Linux and use it in Cadence qspi
  driver.

- Do not set non-volatile Uniform Sector mode bit on S28HS512T. Instead
  use Takahiro's non-uniform erase patch to enable non-uniform erases.

- Make sure spi_nor_write_reg() does not set data direction to out when
  there is no data to write, like in write enable.

- Set buswidths to 0 before calling spi_nor_setup_op(), like how it is
  done in Linux.

Changes in v7:
- Port back changes requested on the Linux series.

- Introduce the flag SPI_NOR_OCTAL_DTR_PP to indicate 8D page program
  support since it can't be detected from SFDP.

- Re-order Profile 1.0 related defines by DWORD order.

- Drop local variables addr_width and dummy in spi_nor_read_sr()
  spi_nor_read_fsr().

- Do not make having command opcode extension as a reserved field fatal.

- Update doc comment for spi_nor_parse_profile1() and
  spi_nor_cypress_octal_dtr_enable() to add missing fields.

- Move rdsr parameter parsing to where opcode is parsed because it is
  from the same DWORD.

- Convert a comment in Profile 1.0 parsing from multi-line to one line.

- Rename 'table' to 'dwords' in xSPI Profile 1.0 parsing.

- Update spi_nor_check_readop() and spi_nor_check_pp() to use
  spi_nor_setup_op() so the buswidths are properly set up for DTR ops.

- Do not set Uniform Sector bit on the Cypress S28HS512T flash if it is
  already set. It will avoid wearing out the non-volatile bit.

- Enable DQS for Micron MT35XU512ABA. No reason not to.

- Avoid enabling 4-byte addressing mode for all DTR ops instead of just
  Octal DTR ops. This is based on the assumption that DTR ops can only
  use 4-byte addressing.

- Make spi_nor_set_fixups() static.

- Add flag SPI_NOR_OCTAL_DTR_PP to both Cypress S28HS512T and Micron
  MT35XU512ABA.

- Use values set up by spi-{rx,tx}-bus-width via device tree to
  determine if the controller supports the op or not. Gives more
  flexibility to choose protocol per-board.

- Use tiny SPI NOR on x530 because of size constraints.

Changes in v6:
- Use "# CONFIG_SPI_FLASH_SMART_HWCAPS is not set" instead of
  "CONFIG_SPI_FLASH_SMART_HWCAPS=n" in x530_defconfig.

Changes in v5:
- Fix build breaking when CONFIG_SPL_SPI_FLASH_TINY is enabled because
  spi-nor-tiny did not have spi_nor_remove().

- The build was breaking in x530 because of SPL size too big. Fix it by
  the below changes.

- Re-introduce old hwcaps selection logic and put the new one behind a
  config. This lets boards with size restrictions use the old logic
  which takes up less space. The code was getting hard to manage with
  the old code behind ifdefs. So, re-structure the old hwcaps selection
  logic and move it into one function: spi_nor_adjust_hwcaps(). This
  way, the common code just calls spi_nor_adjust_hwcaps(), but the old
  or new hwcaps selection is used based on the config option selected.

- Put spi_nor_soft_reset() behind the config option SPI_NOR_SOFT_RESET.

- Rename the config option used for soft resetting on boot to
  SPI_NOR_SOFT_RESET_ON_BOOT to make its intention clearer.

- Put the fixup hooks of MT35XU512ABA and S28HS512T flashes behind
  config options to reduce code size on platforms that don't need them.

- Introduce spi_nor_set_fixups(). Earlier, the fixup members of each
  flash was specified in spi-nor-ids.c. This meant they had to be
  declared as extern in sf_internal.h. But since spi-nor-tiny.c also
  uses it, and it doesn't have those fixups, they had to be put behind
  in an ifdef. The ".fixups = " assignment in spi-nor-ids.c also had to
  be put in an ifdef to account for spi-nor-tiny.c not having the fixup
  hooks. On top of this, the fixup of each flash is behind the flash's
  config.

  All this lead to a soup of ifdefs that wasn't easy to digest. So don't
  set the fixups in the common code. Instead, add a function in
  spi-nor-core.c that sets the fixups of each flash. This isn't ideal,
  but its the best compromise I could figure out.

- Build were breaking with boards that use spi-mem-nodm.c because it
  doesn't have spi_mem_supports_op() which is needed for smart hwcaps
  selection. Add an equivalent to spi_mem_default_supports_op() there.

- Replace uses of sizeof(op->cmd.opcode) with op->cmd.nbytes.

- Do not set quad_enable to NULL if the value is set to reserved.
  Instead just print a warning and go on. quad_enable should be set to
  NULL in fixup hooks instead. Suggested on the Linux list.

- Set dummy cycles for DTR mode in spi_nor_micron_octal_dtr_enable()
  instead of in the post sfdp hook. This keeps the flash functional in
  case Octal DTR mode is not selected.

- Only use nor->rdsr_addr_nbytes and nor->rdsr_dummy when in Octal DTR
  mode. This makes sure the flash is functional in case Octal DTR is not
  selected.

- Rebase on latest master and fix a small merge conflict.

Changes in v4:
- Fix BFPT parsing stopping too early for JESD216 rev B flashes.

- Instead of just checking for spi_nor_get_protocol_width() in
  spi_nor_octal_dtr_enable(), make sure the protocol is
  SNOR_PROTO_8_8_8_DTR since get_protocol_width() only cares about data
  width.

- Do not enable stateful X-X-X modes if the reset line is broken.

- Instead of setting SNOR_READ_HWCAPS_8_8_8_DTR from Profile 1.0 table
  parsing, do it in spi_nor_info_init_params() instead based on the
  SPI_NOR_OCTAL_DTR_READ flag instead.

- Set SNOR_HWCAPS_PP_8_8_8_DTR in s28hs post_sfdp hook since this
  capability is no longer set in Profile 1.0 parsing.

- Rename spi_nor_cypress_octal_enable() to
  spi_nor_cypress_octal_dtr_enable().

- Instead of hard-coding 8D-8D-8D Fast Read dummy cycles to 20, find
  them out from the Profile 1.0 table.

- Call post-bfpt fixup when exiting early because of JESD rev A.

- Do not make an invalid Quad Enable BFPT field a fatal error. Silently
  ignore it by assuming no quad enable bit is present.

- Set cmd.nbytes to 1 when using SPI_MEM_OP_CMD().

- Reject ops with more than 1 command byte in
  spi_mem_default_supports_op().

- Drop flag SPI_NOR_SOFT_RESET. Instead, discover soft reset capability
  via BFPT.

- Add missing headers that were removed from common header.

Changes in v3:
- Read 2 bytes in Octal DTR mode when reading SR and FSR to avoid
  tripping up controllers.

- Use op->data.nbytes as a measure of whether the data phase exists or
  not. This fixes data buswidth not being updadted for SR and FSR reads
  because they keep data buffer as NULL when calling spi_nor_setup_op().

- Add support for Micron mt35xu512aba to run in Octal DTR mode.

Pratyush Yadav (27):
  spi: spi-mem: allow specifying whether an op is DTR or not
  spi: spi-mem: allow specifying a command's extension
  spi: spi-mem: export spi_mem_default_supports_op()
  spi: spi-mem: add spi_mem_dtr_supports_op()
  spi: cadence-qspi: Do not calibrate when device tree sets read delay
  spi: cadence-qspi: Add a small delay before indirect writes
  spi: cadence-qspi: Add support for octal DTR flashes
  arm: mvebu: x530: Use tiny SPI NOR
  mtd: spi-nor-core: Fix address width on flash chips > 16MB
  mtd: spi-nor-core: Add a ->setup() hook
  mtd: spi-nor-core: Move SFDP related declarations to top
  mtd: spi-nor-core: Introduce flash-specific fixup hooks
  mtd: spi-nor-core: Rework hwcaps selection
  mtd: spi-nor-core: Do not set data direction when there is no data
  mtd: spi-nor-core: Add support for DTR protocol
  mtd: spi-nor-core: prepare BFPT parsing for JESD216 rev D
  mtd: spi-nor-core: Get command opcode extension type from BFPT
  mtd: spi-nor-core: Parse xSPI Profile 1.0 table
  mtd: spi-nor-core: Prepare Read SR and FSR for Octal DTR mode
  mtd: spi-nor-core: Enable octal DTR mode when possible
  mtd: spi-nor-core: Do not make invalid quad enable fatal
  mtd: spi-nor-core: Detect Soft Reset sequence support from BFPT
  mtd: spi-nor-core: Perform a Soft Reset on shutdown
  mtd: spi-nor-core: Perform a Soft Reset on boot
  mtd: spi-nor-core: allow truncated erases
  mtd: spi-nor-core: Add support for Cypress Semper flash
  mtd: spi-nor-core: Allow using Micron mt35xu512aba in Octal DTR mode

Takahiro Kuwano (1):
  mtd: spi-nor-core: Add non-uniform erase for Spansion/Cypress

 configs/x530_defconfig         |    1 -
 drivers/mtd/spi/Kconfig        |   42 +
 drivers/mtd/spi/sf_internal.h  |    1 +
 drivers/mtd/spi/sf_probe.c     |    8 +
 drivers/mtd/spi/spi-nor-core.c | 1447 ++++++++++++++++++++++++++------
 drivers/mtd/spi/spi-nor-ids.c  |    7 +-
 drivers/mtd/spi/spi-nor-tiny.c |   22 -
 drivers/spi/cadence_qspi.c     |   69 +-
 drivers/spi/cadence_qspi.h     |   16 +-
 drivers/spi/cadence_qspi_apb.c |  292 ++++++-
 drivers/spi/mtk_snfi_spi.c     |    3 +-
 drivers/spi/spi-mem-nodm.c     |   66 +-
 drivers/spi/spi-mem.c          |   46 +-
 include/linux/mtd/spi-nor.h    |  279 ++++--
 include/spi-mem.h              |   19 +-
 15 files changed, 1923 insertions(+), 395 deletions(-)

--
2.30.0



More information about the U-Boot mailing list