[PATCH 13/27] ppc: Remove sbc8548 boards

Paul Gortmaker paul.gortmaker at windriver.com
Sat May 15 21:18:25 CEST 2021


[[PATCH 13/27] ppc: Remove sbc8548 boards] On 14/05/2021 (Fri 21:34) Tom Rini wrote:

> These boards have not been converted to CONFIG_DM_PCI by the deadline and are
> also missing conversion to CONFIG_DM.  Remove them.
> 
> Cc: Paul Gortmaker <paul.gortmaker at windriver.com>

Ack - kernel removal was queued several months ago, but has yet to be
merged to mainline or linux-next

https://patchwork.ozlabs.org/project/linuxppc-dev/patch/20210111082823.99562-2-paul.gortmaker@windriver.com/

Thanks,
Paul.
--

> Signed-off-by: Tom Rini <trini at konsulko.com>
> ---
>  arch/powerpc/cpu/mpc85xx/Kconfig      |   5 -
>  board/sbc8548/Kconfig                 |   9 -
>  board/sbc8548/MAINTAINERS             |  10 -
>  board/sbc8548/Makefile                |  12 -
>  board/sbc8548/README                  | 269 -------------
>  board/sbc8548/ddr.c                   | 132 -------
>  board/sbc8548/law.c                   |  54 ---
>  board/sbc8548/sbc8548.c               | 315 ---------------
>  board/sbc8548/tlb.c                   | 121 ------
>  configs/sbc8548_PCI_33_PCIE_defconfig |  42 --
>  configs/sbc8548_PCI_33_defconfig      |  42 --
>  configs/sbc8548_PCI_66_PCIE_defconfig |  42 --
>  configs/sbc8548_PCI_66_defconfig      |  42 --
>  configs/sbc8548_defconfig             |  41 --
>  include/configs/sbc8548.h             | 540 --------------------------
>  15 files changed, 1676 deletions(-)
>  delete mode 100644 board/sbc8548/Kconfig
>  delete mode 100644 board/sbc8548/MAINTAINERS
>  delete mode 100644 board/sbc8548/Makefile
>  delete mode 100644 board/sbc8548/README
>  delete mode 100644 board/sbc8548/ddr.c
>  delete mode 100644 board/sbc8548/law.c
>  delete mode 100644 board/sbc8548/sbc8548.c
>  delete mode 100644 board/sbc8548/tlb.c
>  delete mode 100644 configs/sbc8548_PCI_33_PCIE_defconfig
>  delete mode 100644 configs/sbc8548_PCI_33_defconfig
>  delete mode 100644 configs/sbc8548_PCI_66_PCIE_defconfig
>  delete mode 100644 configs/sbc8548_PCI_66_defconfig
>  delete mode 100644 configs/sbc8548_defconfig
>  delete mode 100644 include/configs/sbc8548.h
> 
> diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
> index 676aaf1d2ca6..22cfa4dc3499 100644
> --- a/arch/powerpc/cpu/mpc85xx/Kconfig
> +++ b/arch/powerpc/cpu/mpc85xx/Kconfig
> @@ -16,10 +16,6 @@ choice
>  	prompt "Target select"
>  	optional
>  
> -config TARGET_SBC8548
> -	bool "Support sbc8548"
> -	select ARCH_MPC8548
> -
>  config TARGET_SOCRATES
>  	bool "Support socrates"
>  	select ARCH_MPC8544
> @@ -1303,7 +1299,6 @@ source "board/freescale/t208xqds/Kconfig"
>  source "board/freescale/t208xrdb/Kconfig"
>  source "board/freescale/t4rdb/Kconfig"
>  source "board/keymile/Kconfig"
> -source "board/sbc8548/Kconfig"
>  source "board/socrates/Kconfig"
>  source "board/xes/xpedite520x/Kconfig"
>  source "board/xes/xpedite537x/Kconfig"
> diff --git a/board/sbc8548/Kconfig b/board/sbc8548/Kconfig
> deleted file mode 100644
> index 626cbdf2ab27..000000000000
> --- a/board/sbc8548/Kconfig
> +++ /dev/null
> @@ -1,9 +0,0 @@
> -if TARGET_SBC8548
> -
> -config SYS_BOARD
> -	default "sbc8548"
> -
> -config SYS_CONFIG_NAME
> -	default "sbc8548"
> -
> -endif
> diff --git a/board/sbc8548/MAINTAINERS b/board/sbc8548/MAINTAINERS
> deleted file mode 100644
> index ba1f2475eabf..000000000000
> --- a/board/sbc8548/MAINTAINERS
> +++ /dev/null
> @@ -1,10 +0,0 @@
> -SBC8548 BOARD
> -M:	Paul Gortmaker <paul.gortmaker at windriver.com>
> -S:	Maintained
> -F:	board/sbc8548/
> -F:	include/configs/sbc8548.h
> -F:	configs/sbc8548_defconfig
> -F:	configs/sbc8548_PCI_33_defconfig
> -F:	configs/sbc8548_PCI_33_PCIE_defconfig
> -F:	configs/sbc8548_PCI_66_defconfig
> -F:	configs/sbc8548_PCI_66_PCIE_defconfig
> diff --git a/board/sbc8548/Makefile b/board/sbc8548/Makefile
> deleted file mode 100644
> index 83d208cf1fe9..000000000000
> --- a/board/sbc8548/Makefile
> +++ /dev/null
> @@ -1,12 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# (C) Copyright 2004-2006
> -# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> -#
> -# (C) Copyright 2007 Wind River Systems Inc <www.windriver.com>.
> -# Added support for Wind River SBC8548 board
> -
> -obj-y	+= sbc8548.o
> -obj-y	+= law.o
> -obj-y	+= tlb.o
> -obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
> diff --git a/board/sbc8548/README b/board/sbc8548/README
> deleted file mode 100644
> index 0def245bd9ce..000000000000
> --- a/board/sbc8548/README
> +++ /dev/null
> @@ -1,269 +0,0 @@
> -Intro:
> -======
> -
> -The SBC8548 is a stand alone single board computer with a 1GHz
> -MPC8548 CPU, 8MB boot flash, 64MB user flash and, 256MB DDR2 400MHz
> -memory. It also has 128MB SDRAM 100MHz LBC memory, with both a PCI-e,
> -and a PCI-X slot, dual mini-DB9 for UART, and dual RJ-45 for eTSEC
> -ethernet connections.
> -
> -U-Boot Configuration:
> -=====================
> -
> -The following possible U-Boot configuration targets are available:
> -
> -	1) sbc8548_config
> -	2) sbc8548_PCI_33_config
> -	3) sbc8548_PCI_66_config
> -	4) sbc8548_PCI_33_PCIE_config
> -	5) sbc8548_PCI_66_PCIE_config
> -
> -Generally speaking, most people should choose to use #5.  Details
> -of each choice are listed below.
> -
> -Choice #1 does not enable CONFIG_PCI, and assumes that the PCI slot
> -will be left empty (M66EN high), and so the board will operate with
> -a base clock of 66MHz.	Note that you need both PCI enabled in U-Boot
> -and linux in order to have functional PCI under linux.
> -
> -The second enables PCI support and builds for a 33MHz clock rate.  Note
> -that if a 33MHz 32bit card is inserted in the slot, then the whole board
> -will clock down to a 33MHz base clock instead of the default 66MHz.  This
> -will change the baud clocks and mess up your serial console output if you
> -were previously running at 66MHz.  If you want to use a 33MHz PCI card,
> -then you should build a U-Boot with a _PCI_33_ config and store this
> -to flash prior to powering down the board and inserting the 33MHz PCI
> -card. [The above discussion assumes that the SW2[1-4] has not been changed
> -to reflect a different CCB:SYSCLK ratio]
> -
> -The third option builds PCI support in, and leaves the clocking at the
> -default 66MHz.	Options four and five are just repeats of option two
> -and three, but with PCI-e support enabled as well.
> -
> -PCI output listing with an intel e1000 PCI-x and a Syskonnect SK-9Exx
> -is shown below for sbc8548_PCI_66_PCIE_config.	(Note that PCI-e with
> -a 33MHz PCI configuration is currently untested.)
> -
> -    => pci 0
> -    Scanning PCI devices on bus 0
> -    BusDevFun  VendorId	  DeviceId   Device Class	Sub-Class
> -    _____________________________________________________________
> -    00.00.00   0x1057	  0x0012     Processor		     0x20
> -    00.01.00   0x8086	  0x1026     Network controller	     0x00
> -    => pci 1
> -    Scanning PCI devices on bus 1
> -    BusDevFun  VendorId	  DeviceId   Device Class	Sub-Class
> -    _____________________________________________________________
> -    01.00.00   0x1957	  0x0012     Processor		     0x20
> -    => pci 2
> -    Scanning PCI devices on bus 2
> -    BusDevFun  VendorId	  DeviceId   Device Class	Sub-Class
> -    _____________________________________________________________
> -    02.00.00   0x1148	  0x9e00     Network controller	     0x00
> -    =>
> -
> -Memory Size and using SPD:
> -==========================
> -
> -The default configuration uses hard coded memory configuration settings
> -for 256MB of DDR2 @400MHz.  It does not by default use the DDR2 SPD
> -EEPROM data to read what memory is installed.
> -
> -There is a hardware errata, which causes the older local bus SDRAM
> -SPD EEPROM to land at the same address as the DDR2 SPD EEPROM, so
> -that the SPD data can not be read reliably.  You can test if your
> -board has the errata fix by running "i2c probe".  If you see 0x53
> -as a valid device, it has been fixed.  If you only see 0x50, 0x51
> -then your board does not have the fix.
> -
> -You can also visually inspect the board to see if this hardware
> -fix has been applied:
> -
> -      1) Remove R314 (RES-R0174-033, 1K, 0603). R314 is located on
> -	 the back of the PCB behind the DDR SDRAM SODIMM connector.
> -      2) Solder RES-R0174-033 (1K, 0603) resistor from R314 pin 2 pad
> -	 to R313 pin 2.	 Pin 2 for each resistor is the end of the
> -	 resistor closest to the CPU.
> -
> -Boards without the mod will have R314 and R313 in parallel, like "||".
> -After the mod, they will be touching and form an "L" shape.
> -
> -If you want to upgrade to larger RAM size, you can simply enable
> -	#define CONFIG_SPD_EEPROM
> -	#define CONFIG_DDR_SPD
> -in include/configs/sbc8548.h file.  (The lines are already there
> -but listed as #undef).
> -
> -If you did the i2c test, and your board does not have the errata
> -fix, then you will have to physically remove the LBC 128MB DIMM
> -from the board's socket to resolve the above i2c address overlap
> -issue and allow SPD autodetection of RAM to work.
> -
> -
> -Updating U-Boot with U-Boot:
> -============================
> -
> -Note that versions of U-Boot up to and including 2009.08 had U-Boot stored
> -at 0xfff8_0000 -> 0xffff_ffff (512k).  Currently it is being stored from
> -0xfffa_0000 -> 0xffff_ffff (384k).  If you use an old macro/script to
> -update U-Boot with U-Boot and it uses the old address, you will render
> -your board inoperable, and you will require JTAG recovery.
> -
> -The following steps list how to update with the current address:
> -
> -	tftp u-boot.bin
> -	md 200000 10
> -	protect off all
> -	erase fffa0000 ffffffff
> -	cp.b 200000 fffa0000 60000
> -	md fffa0000 10
> -	protect on all
> -
> -The "md" steps in the above are just a precautionary step that allow
> -you to confirm the U-Boot version that was downloaded, and then confirm
> -that it was copied to flash.
> -
> -The above assumes that you are using the default board settings which
> -have U-Boot in the 8MB flash, tied to /CS0.
> -
> -If you are running the default 8MB /CS0 settings but want to store an
> -image in the SODIMM that is built with CONFIG_SYS_ALT_BOOT enabled,
> -(as a backup, etc) then the steps will become:
> -
> -	tftp u-boot.bin
> -	md 200000 10
> -	protect off all
> -	era eff00000 efffffff
> -	cp.b 200000 eff00000 100000
> -	md eff00000 10
> -	protect on all
> -
> -Finally, if you are running the alternate 64MB /CS0 settings and want
> -to update the in-use U-Boot image, then (again with CONFIG_SYS_ALT_BOOT
> -enabled) the steps will become:
> -
> -	tftp u-boot.bin
> -	md 200000 10
> -	protect off all
> -	era fff00000 ffffffff
> -	cp.b 200000 fff00000 100000
> -	md fff00000 10
> -	protect on all
> -
> -
> -Hardware Reference:
> -===================
> -
> -The following contains some summary information on hardware settings
> -that are relevant to U-Boot, based on the board manual.	 For the
> -most up to date and complete details of the board, please request the
> -reference manual ERG-00327-001.pdf from www.windriver.com
> -
> -Boot flash:
> -	intel V28F640Jx, 8192x8 (one device) at 0xff80_0000
> -
> -Sodimm flash:
> -	intel V28F128Jx, 16384x8 (4 devices) at 0xfb80_0000
> -	Note that this address reflects the default setting for
> -	the JTAG debugging tools, but since the alignment is
> -	rather inconvenient, U-Boot puts it at 0xec00_0000.
> -
> -
> -	Jumpers:
> -
> -Jumper		Name		ON		OFF
> -----------------------------------------------------------------
> -JP12		CS0/CS6 swap	see note[*]	see note[*]
> -
> -JP13		SODIMM flash	write OK	writes disabled
> -		write prot.
> -
> -JP14		HRESET/TRST	joined		isolated
> -
> -JP15		PWR ON		when AC pwr	use S1 for on/off
> -
> -JP16		Demo LEDs	lit		not lit
> -
> -JP19		PCI mode	PCI		PCI-X
> -
> -
> -[*]JP12, when jumpered parallel to the SODIMM, puts the boot flash
> -onto /CS0 and the SODIMM flash on /CS6 (default).  When JP12
> -is jumpered parallel to the LBC-SDRAM, then /CS0 is for the
> -SODIMM flash and /CS6 is for the boot flash.  Note that in this
> -alternate setting, you also need to switch SW2.8 to ON.
> -See the setting CONFIG_SYS_ALT_BOOT if you want to use this setting
> -and boot U-Boot from the 64MB SODIMM
> -
> -
> -	Switches:
> -
> -The defaults are marked with a *
> -
> -Name		Desc.			ON		OFF
> -------------------------------------------------------------------
> -S1		Pwr toggle		n/a		n/a
> -
> -SW2.1		CFG_SYS_PLL0		1		0*
> -SW2.2		CFG_SYS_PLL1		1*		0
> -SW2.3		CFG_SYS_PLL2		1*		0
> -SW2.4		CFG_SYS_PLL3		1		0*
> -SW2.5		CFG_CORE_PLL0		1*		0
> -SW2.6		CFG_CORE_PLL1		1		0*
> -SW2.7		CFG_CORE_PLL2		1*		0
> -SW2.8		CFG_ROM_LOC1		1		0*
> -
> -SW3.1		CFG_HOST_AGT0		1*		0
> -SW3.2		CFG_HOST_AGT1		1*		0
> -SW3.3		CFG_HOST_AGT2		1*		0
> -SW3.4		CFG_IO_PORTS0		1*		0
> -SW3.5		CFG_IO_PORTS0		1		0*
> -SW3.6		CFG_IO_PORTS0		1		0*
> -
> -SerDes CLK(MHz)		SW5.1		SW5.2
> -----------------------------------------------
> -25			0		0
> -100*			1		0
> -125			0		1
> -200			1		1
> -
> -SerDes CLK spread	SW5.3		SW5.4
> -----------------------------------------------
> -+/- 0.25%		0		0
> --0.50%			1		0
> --0.75%			0		1
> -No Spread*		1		1
> -
> -SW4 settings are readable from the EPLD and are currently not used for
> -any hardware settings (i.e. user configuration switches).
> -
> -	LEDs:
> -
> -Name		Desc.			ON		OFF
> -------------------------------------------------------------------
> -D13		PCI/PCI-X		PCI-X		PCI
> -D14		3.3V PWR		3.3V		no power
> -D15		SYSCLK			66MHz		33MHz
> -
> -
> -	Default Memory Map:
> -
> -start		end		CS<n>	width	Desc.
> -----------------------------------------------------------------------
> -0000_0000	0fff_ffff	MCS0,1	64	DDR2 (256MB)
> -f000_0000	f7ff_ffff	CS3,4	32	LB SDRAM (128MB)
> -f800_0000	f8b0_1fff	CS5	-	EPLD
> -fb80_0000	ff7f_ffff	CS6	32	SODIMM flash (64MB) [*]
> -ff80_0000	ffff_ffff	CS0	8	Boot flash (8MB)
> -
> -[*] fb80 represents the default programmed by WR JTAG register files,
> -    but U-Boot places the flash at either ec00 or fc00 based on JP12.
> -
> -The EPLD on CS5 demuxes the following devices at the following offsets:
> -
> -offset		size	width	device
> ---------------------------------------------------------
> -0		1fff	8	7 segment display LED
> -10_0000		1fff	4	user switches
> -30_0000		1fff	4	HW Rev. register
> -b0_0000		1fff	8	8kB EEPROM
> diff --git a/board/sbc8548/ddr.c b/board/sbc8548/ddr.c
> deleted file mode 100644
> index 61bc77c418a9..000000000000
> --- a/board/sbc8548/ddr.c
> +++ /dev/null
> @@ -1,132 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Copyright 2008 Freescale Semiconductor, Inc.
> - */
> -
> -#include <common.h>
> -#include <i2c.h>
> -#include <linux/delay.h>
> -
> -#include <fsl_ddr_sdram.h>
> -#include <fsl_ddr_dimm_params.h>
> -
> -void fsl_ddr_board_options(memctl_options_t *popts,
> -				dimm_params_t *pdimm,
> -				unsigned int ctrl_num)
> -{
> -	/*
> -	 * Factors to consider for clock adjust:
> -	 *	- number of chips on bus
> -	 *	- position of slot
> -	 *	- DDR1 vs. DDR2?
> -	 *	- ???
> -	 *
> -	 * This needs to be determined on a board-by-board basis.
> -	 *	0110	3/4 cycle late
> -	 *	0111	7/8 cycle late
> -	 */
> -	popts->clk_adjust = 7;
> -
> -	/*
> -	 * Factors to consider for CPO:
> -	 *	- frequency
> -	 *	- ddr1 vs. ddr2
> -	 */
> -	popts->cpo_override = 10;
> -
> -	/*
> -	 * Factors to consider for write data delay:
> -	 *	- number of DIMMs
> -	 *
> -	 * 1 = 1/4 clock delay
> -	 * 2 = 1/2 clock delay
> -	 * 3 = 3/4 clock delay
> -	 * 4 = 1   clock delay
> -	 * 5 = 5/4 clock delay
> -	 * 6 = 3/2 clock delay
> -	 */
> -	popts->write_data_delay = 3;
> -
> -	/*
> -	 * Factors to consider for half-strength driver enable:
> -	 *	- number of DIMMs installed
> -	 */
> -	popts->half_strength_driver_enable = 0;
> -}
> -
> -#ifdef CONFIG_SPD_EEPROM
> -/*
> - * Workaround for hardware errata.  An i2c address conflict
> - * existed on earlier boards; the workaround moved the DDR
> - * SPD from 0x51 to 0x53.  So we try and read 0x53 1st, and
> - * if that fails, then fall back to reading at 0x51.
> - */
> -void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
> -{
> -	int ret;
> -
> -#ifdef ALT_SPD_EEPROM_ADDRESS
> -	if (i2c_address == SPD_EEPROM_ADDRESS) {
> -		ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
> -				sizeof(generic_spd_eeprom_t));
> -		if (ret == 0)
> -			return;		/* Good data at 0x53 */
> -		memset(spd, 0, sizeof(generic_spd_eeprom_t));
> -	}
> -#endif
> -	ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
> -				sizeof(generic_spd_eeprom_t));
> -	if (ret) {
> -		printf("DDR: failed to read SPD from addr %u\n", i2c_address);
> -		memset(spd, 0, sizeof(generic_spd_eeprom_t));
> -	}
> -}
> -
> -#else
> -/*
> - *  fixed_sdram init -- doesn't use serial presence detect.
> - *  Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
> - */
> -phys_size_t fixed_sdram(void)
> -{
> -	struct ccsr_ddr __iomem *ddr =
> -		(struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
> -
> -	out_be32(&ddr->cs0_bnds,	0x0000007f);
> -	out_be32(&ddr->cs1_bnds,	0x008000ff);
> -	out_be32(&ddr->cs2_bnds,	0x00000000);
> -	out_be32(&ddr->cs3_bnds,	0x00000000);
> -
> -	out_be32(&ddr->cs0_config,	0x80010101);
> -	out_be32(&ddr->cs1_config,	0x80010101);
> -	out_be32(&ddr->cs2_config,	0x00000000);
> -	out_be32(&ddr->cs3_config,	0x00000000);
> -
> -	out_be32(&ddr->timing_cfg_3,	0x00000000);
> -	out_be32(&ddr->timing_cfg_0,	0x00220802);
> -	out_be32(&ddr->timing_cfg_1,	0x38377322);
> -	out_be32(&ddr->timing_cfg_2,	0x0fa044C7);
> -
> -	out_be32(&ddr->sdram_cfg,	0x4300C000);
> -	out_be32(&ddr->sdram_cfg_2,	0x24401000);
> -
> -	out_be32(&ddr->sdram_mode,	0x23C00542);
> -	out_be32(&ddr->sdram_mode_2,	0x00000000);
> -
> -	out_be32(&ddr->sdram_interval,	0x05080100);
> -	out_be32(&ddr->sdram_md_cntl,	0x00000000);
> -	out_be32(&ddr->sdram_data_init,	0x00000000);
> -	out_be32(&ddr->sdram_clk_cntl,	0x03800000);
> -	asm("sync;isync;msync");
> -	udelay(500);
> -
> -	#ifdef CONFIG_DDR_ECC
> -	  /* Enable ECC checking */
> -	  out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
> -	#else
> -	  out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
> -	#endif
> -
> -	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
> -}
> -#endif
> diff --git a/board/sbc8548/law.c b/board/sbc8548/law.c
> deleted file mode 100644
> index 97271ea6f66b..000000000000
> --- a/board/sbc8548/law.c
> +++ /dev/null
> @@ -1,54 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright 2008 Freescale Semiconductor, Inc.
> - *
> - * (C) Copyright 2000
> - * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> - */
> -
> -#include <common.h>
> -#include <asm/fsl_law.h>
> -#include <asm/mmu.h>
> -
> -/*
> - * LAW(Local Access Window) configuration:
> - *
> - * 0x0000_0000	0x0fff_ffff	DDR			256M
> - * 0x8000_0000	0x9fff_ffff	PCI1 MEM		512M
> - * 0xa000_0000	0xbfff_ffff	PCIe MEM		512M
> - * 0xe000_0000	0xe000_ffff	CCSR			1M
> - * 0xe200_0000	0xe27f_ffff	PCI1 IO			8M
> - * 0xe280_0000	0xe2ff_ffff	PCIe IO			8M
> - * 0xec00_0000	0xefff_ffff	FLASH (2nd bank)	64M
> - * 0xf000_0000	0xf7ff_ffff	SDRAM			128M
> - * 0xf8b0_0000	0xf80f_ffff	EEPROM			1M
> - * 0xff80_0000	0xffff_ffff	FLASH (boot bank)	8M
> - *
> - * If swapped CS0/CS6 via JP12+SW2.8:
> - * 0xef80_0000	0xefff_ffff	FLASH (2nd bank)	8M
> - * 0xfc00_0000	0xffff_ffff	FLASH (boot bank)	64M
> - *
> - * Notes:
> - *	CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
> - *	If flash is 8M at default position (last 8M), no LAW needed.
> - */
> -
> -struct law_entry law_table[] = {
> -#ifdef CONFIG_SYS_ALT_BOOT
> -	SET_LAW(CONFIG_SYS_ALT_FLASH, LAW_SIZE_8M, LAW_TRGT_IF_LBC),
> -#else
> -	SET_LAW(CONFIG_SYS_ALT_FLASH, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
> -#endif
> -#ifndef CONFIG_SPD_EEPROM
> -	SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
> -#endif
> -#ifdef CONFIG_SYS_LBC_SDRAM_BASE
> -	/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
> -	SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
> -#else
> -	/* LBC window - maps 128M 0xf8000000 -> 0xffffffff */
> -	SET_LAW(CONFIG_SYS_EPLD_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
> -#endif
> -};
> -
> -int num_law_entries = ARRAY_SIZE(law_table);
> diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c
> deleted file mode 100644
> index bd4b528d03f7..000000000000
> --- a/board/sbc8548/sbc8548.c
> +++ /dev/null
> @@ -1,315 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright 2007,2009 Wind River Systems, Inc. <www.windriver.com>
> - *
> - * Copyright 2007 Embedded Specialties, Inc.
> - *
> - * Copyright 2004, 2007 Freescale Semiconductor.
> - *
> - * (C) Copyright 2002 Scott McNutt <smcnutt at artesyncp.com>
> - */
> -
> -#include <common.h>
> -#include <init.h>
> -#include <log.h>
> -#include <net.h>
> -#include <pci.h>
> -#include <asm/processor.h>
> -#include <asm/immap_85xx.h>
> -#include <asm/fsl_pci.h>
> -#include <fsl_ddr_sdram.h>
> -#include <asm/fsl_serdes.h>
> -#include <spd_sdram.h>
> -#include <netdev.h>
> -#include <tsec.h>
> -#include <miiphy.h>
> -#include <linux/delay.h>
> -#include <linux/libfdt.h>
> -#include <fdt_support.h>
> -
> -void local_bus_init(void);
> -
> -int board_early_init_f (void)
> -{
> -	return 0;
> -}
> -
> -int checkboard (void)
> -{
> -	volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
> -	volatile u_char *rev= (void *)CONFIG_SYS_BD_REV;
> -
> -	printf ("Board: Wind River SBC8548 Rev. 0x%01x\n",
> -			in_8(rev) >> 4);
> -
> -	/*
> -	 * Initialize local bus.
> -	 */
> -	local_bus_init ();
> -
> -	out_be32(&ecm->eedr, 0xffffffff);	/* clear ecm errors */
> -	out_be32(&ecm->eeer, 0xffffffff);	/* enable ecm errors */
> -	return 0;
> -}
> -
> -/*
> - * Initialize Local Bus
> - */
> -void
> -local_bus_init(void)
> -{
> -	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
> -	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
> -
> -	uint clkdiv, lbc_mhz, lcrr = CONFIG_SYS_LBC_LCRR;
> -	sys_info_t sysinfo;
> -
> -	get_sys_info(&sysinfo);
> -
> -	lbc_mhz = sysinfo.freq_localbus / 1000000;
> -	clkdiv = sysinfo.freq_systembus / sysinfo.freq_localbus;
> -
> -	debug("LCRR=0x%x, CD=%d, MHz=%d\n", lcrr, clkdiv, lbc_mhz);
> -
> -	out_be32(&gur->lbiuiplldcr1, 0x00078080);
> -	if (clkdiv == 16) {
> -		out_be32(&gur->lbiuiplldcr0, 0x7c0f1bf0);
> -	} else if (clkdiv == 8) {
> -		out_be32(&gur->lbiuiplldcr0, 0x6c0f1bf0);
> -	} else if (clkdiv == 4) {
> -		out_be32(&gur->lbiuiplldcr0, 0x5c0f1bf0);
> -	}
> -
> -	/*
> -	 * Local Bus Clock > 83.3 MHz. According to timing
> -	 * specifications set LCRR[EADC] to 2 delay cycles.
> -	 */
> -	if (lbc_mhz > 83) {
> -		lcrr &= ~LCRR_EADC;
> -		lcrr |= LCRR_EADC_2;
> -	}
> -
> -	/*
> -	 * According to MPC8548ERMAD Rev. 1.3, 13.3.1.16, 13-30
> -	 * disable PLL bypass for Local Bus Clock > 83 MHz.
> -	 */
> -	if (lbc_mhz >= 66)
> -		lcrr &= (~LCRR_DBYP);	/* DLL Enabled */
> -
> -	else
> -		lcrr |= LCRR_DBYP;	/* DLL Bypass */
> -
> -	out_be32(&lbc->lcrr, lcrr);
> -	asm("sync;isync;msync");
> -
> -	 /*
> -	 * According to MPC8548ERMAD Rev.1.3 read back LCRR
> -	 * and terminate with isync
> -	 */
> -	lcrr = in_be32(&lbc->lcrr);
> -	asm ("isync;");
> -
> -	/* let DLL stabilize */
> -	udelay(500);
> -
> -	out_be32(&lbc->ltesr, 0xffffffff);	/* Clear LBC error IRQs */
> -	out_be32(&lbc->lteir, 0xffffffff);	/* Enable LBC error IRQs */
> -}
> -
> -/*
> - * Initialize SDRAM memory on the Local Bus.
> - */
> -void lbc_sdram_init(void)
> -{
> -#if defined(CONFIG_SYS_LBC_SDRAM_SIZE)
> -
> -	uint idx;
> -	const unsigned long size = CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024;
> -	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
> -	uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
> -	uint *sdram_addr2 = (uint *)(CONFIG_SYS_LBC_SDRAM_BASE + size/2);
> -
> -	puts("    SDRAM: ");
> -
> -	print_size(size, "\n");
> -
> -	/*
> -	 * Setup SDRAM Base and Option Registers
> -	 */
> -	set_lbc_or(3, CONFIG_SYS_OR3_PRELIM);
> -	set_lbc_br(3, CONFIG_SYS_BR3_PRELIM);
> -	set_lbc_or(4, CONFIG_SYS_OR4_PRELIM);
> -	set_lbc_br(4, CONFIG_SYS_BR4_PRELIM);
> -
> -	out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
> -	asm("msync");
> -
> -	out_be32(&lbc->lsrt,  CONFIG_SYS_LBC_LSRT);
> -	out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
> -	asm("msync");
> -
> -	/*
> -	 * Issue PRECHARGE ALL command.
> -	 */
> -	out_be32(&lbc->lsdmr, CONFIG_SYS_LBC_LSDMR_PCHALL);
> -	asm("sync;msync");
> -	*sdram_addr = 0xff;
> -	ppcDcbf((unsigned long) sdram_addr);
> -	*sdram_addr2 = 0xff;
> -	ppcDcbf((unsigned long) sdram_addr2);
> -	udelay(100);
> -
> -	/*
> -	 * Issue 8 AUTO REFRESH commands.
> -	 */
> -	for (idx = 0; idx < 8; idx++) {
> -		out_be32(&lbc->lsdmr, CONFIG_SYS_LBC_LSDMR_ARFRSH);
> -		asm("sync;msync");
> -		*sdram_addr = 0xff;
> -		ppcDcbf((unsigned long) sdram_addr);
> -		*sdram_addr2 = 0xff;
> -		ppcDcbf((unsigned long) sdram_addr2);
> -		udelay(100);
> -	}
> -
> -	/*
> -	 * Issue 8 MODE-set command.
> -	 */
> -	out_be32(&lbc->lsdmr, CONFIG_SYS_LBC_LSDMR_MRW);
> -	asm("sync;msync");
> -	*sdram_addr = 0xff;
> -	ppcDcbf((unsigned long) sdram_addr);
> -	*sdram_addr2 = 0xff;
> -	ppcDcbf((unsigned long) sdram_addr2);
> -	udelay(100);
> -
> -	/*
> -	 * Issue RFEN command.
> -	 */
> -	out_be32(&lbc->lsdmr, CONFIG_SYS_LBC_LSDMR_RFEN);
> -	asm("sync;msync");
> -	*sdram_addr = 0xff;
> -	ppcDcbf((unsigned long) sdram_addr);
> -	*sdram_addr2 = 0xff;
> -	ppcDcbf((unsigned long) sdram_addr2);
> -	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
> -
> -#endif	/* enable SDRAM init */
> -}
> -
> -#if defined(CONFIG_SYS_DRAM_TEST)
> -int
> -testdram(void)
> -{
> -	uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
> -	uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
> -	uint *p;
> -
> -	printf("Testing DRAM from 0x%08x to 0x%08x\n",
> -	       CONFIG_SYS_MEMTEST_START,
> -	       CONFIG_SYS_MEMTEST_END);
> -
> -	printf("DRAM test phase 1:\n");
> -	for (p = pstart; p < pend; p++)
> -		*p = 0xaaaaaaaa;
> -
> -	for (p = pstart; p < pend; p++) {
> -		if (*p != 0xaaaaaaaa) {
> -			printf ("DRAM test fails at: %08x\n", (uint) p);
> -			return 1;
> -		}
> -	}
> -
> -	printf("DRAM test phase 2:\n");
> -	for (p = pstart; p < pend; p++)
> -		*p = 0x55555555;
> -
> -	for (p = pstart; p < pend; p++) {
> -		if (*p != 0x55555555) {
> -			printf ("DRAM test fails at: %08x\n", (uint) p);
> -			return 1;
> -		}
> -	}
> -
> -	printf("DRAM test passed.\n");
> -	return 0;
> -}
> -#endif
> -
> -#ifdef CONFIG_PCI1
> -static struct pci_controller pci1_hose;
> -#endif	/* CONFIG_PCI1 */
> -
> -#ifdef CONFIG_PCI
> -void
> -pci_init_board(void)
> -{
> -	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
> -	int first_free_busno = 0;
> -
> -#ifdef CONFIG_PCI1
> -	struct fsl_pci_info pci_info;
> -	u32 devdisr = in_be32(&gur->devdisr);
> -	u32 pordevsr = in_be32(&gur->pordevsr);
> -	u32 porpllsr = in_be32(&gur->porpllsr);
> -
> -	if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
> -		uint pci_32 = pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32;
> -		uint pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
> -		uint pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
> -		uint pci_speed = CONFIG_SYS_CLK_FREQ;	/* get_clock_freq() */
> -
> -		printf("PCI: Host, %d bit, %s MHz, %s, %s\n",
> -			(pci_32) ? 32 : 64,
> -			(pci_speed == 33000000) ? "33" :
> -			(pci_speed == 66000000) ? "66" : "unknown",
> -			pci_clk_sel ? "sync" : "async",
> -			pci_arb ? "arbiter" : "external-arbiter");
> -
> -		SET_STD_PCI_INFO(pci_info, 1);
> -		set_next_law(pci_info.mem_phys,
> -			law_size_bits(pci_info.mem_size), pci_info.law);
> -		set_next_law(pci_info.io_phys,
> -			law_size_bits(pci_info.io_size), pci_info.law);
> -
> -		first_free_busno = fsl_pci_init_port(&pci_info,
> -					&pci1_hose, first_free_busno);
> -	} else {
> -		printf("PCI: disabled\n");
> -	}
> -
> -	puts("\n");
> -#else
> -	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
> -#endif
> -
> -	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI2); /* disable PCI2 */
> -
> -	fsl_pcie_init_board(first_free_busno);
> -}
> -#endif
> -
> -int board_eth_init(struct bd_info *bis)
> -{
> -	tsec_standard_init(bis);
> -	pci_eth_init(bis);
> -	return 0;	/* otherwise cpu_eth_init gets run */
> -}
> -
> -int last_stage_init(void)
> -{
> -	return 0;
> -}
> -
> -#if defined(CONFIG_OF_BOARD_SETUP)
> -int ft_board_setup(void *blob, struct bd_info *bd)
> -{
> -	ft_cpu_setup(blob, bd);
> -
> -#ifdef CONFIG_FSL_PCI_INIT
> -	FT_FSL_PCI_SETUP;
> -#endif
> -
> -	return 0;
> -}
> -#endif
> diff --git a/board/sbc8548/tlb.c b/board/sbc8548/tlb.c
> deleted file mode 100644
> index 8ad01d10e49b..000000000000
> --- a/board/sbc8548/tlb.c
> +++ /dev/null
> @@ -1,121 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright 2008 Freescale Semiconductor, Inc.
> - *
> - * (C) Copyright 2000
> - * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> - */
> -
> -#include <common.h>
> -#include <asm/mmu.h>
> -
> -struct fsl_e_tlb_entry tlb_table[] = {
> -	/* TLB 0 - for temp stack in cache */
> -	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
> -		      0, 0, BOOKE_PAGESZ_4K, 0),
> -	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
> -		      CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
> -		      0, 0, BOOKE_PAGESZ_4K, 0),
> -	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
> -		      CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
> -		      0, 0, BOOKE_PAGESZ_4K, 0),
> -	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
> -		      CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
> -		      0, 0, BOOKE_PAGESZ_4K, 0),
> -
> -	/*
> -	 * TLB 0:	64M	Non-cacheable, guarded
> -	 * 0xfc000000	56M	unused
> -	 * 0xff800000	8M	boot FLASH
> -	 *	.... or ....
> -	 * 0xfc000000	64M	user flash
> -	 *
> -	 * Out of reset this entry is only 4K.
> -	 */
> -	SET_TLB_ENTRY(1, 0xfc000000, 0xfc000000,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 0, BOOKE_PAGESZ_64M, 1),
> -
> -	/*
> -	 * TLB 1:	1G	Non-cacheable, guarded
> -	 * 0x80000000	512M	PCI1 MEM
> -	 * 0xa0000000	512M	PCIe MEM
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT, CONFIG_SYS_PCI1_MEM_PHYS,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 1, BOOKE_PAGESZ_1G, 1),
> -
> -	/*
> -	 * TLB 2:	64M	Non-cacheable, guarded
> -	 * 0xe0000000	1M	CCSRBAR
> -	 * 0xe2000000	8M	PCI1 IO
> -	 * 0xe2800000	8M	PCIe IO
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 2, BOOKE_PAGESZ_64M, 1),
> -
> -#ifdef CONFIG_SYS_LBC_SDRAM_BASE
> -	/*
> -	 * TLB 3:	64M	Cacheable, non-guarded
> -	 * 0xf0000000	64M	LBC SDRAM First half
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
> -		      0, 3, BOOKE_PAGESZ_64M, 1),
> -
> -	/*
> -	 * TLB 4:	64M	Cacheable, non-guarded
> -	 * 0xf4000000	64M	LBC SDRAM Second half
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE + 0x4000000,
> -		      CONFIG_SYS_LBC_SDRAM_BASE + 0x4000000,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
> -		      0, 4, BOOKE_PAGESZ_64M, 1),
> -#endif
> -
> -	/*
> -	 * TLB 5:	16M	Cacheable, non-guarded
> -	 * 0xf8000000	1M	7-segment LED display
> -	 * 0xf8100000	1M	User switches
> -	 * 0xf8300000	1M	Board revision
> -	 * 0xf8b00000	1M	EEPROM
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_EPLD_BASE, CONFIG_SYS_EPLD_BASE,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 5, BOOKE_PAGESZ_16M, 1),
> -
> -#ifndef CONFIG_SYS_ALT_BOOT
> -	/*
> -	 * TLB 6:	64M	Non-cacheable, guarded
> -	 * 0xec000000	64M	64MB user FLASH
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH, CONFIG_SYS_ALT_FLASH,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 6, BOOKE_PAGESZ_64M, 1),
> -#else
> -	/*
> -	 * TLB 6:	4M	Non-cacheable, guarded
> -	 * 0xef800000	4M	1st 1/2 8MB soldered FLASH
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH, CONFIG_SYS_ALT_FLASH,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 6, BOOKE_PAGESZ_4M, 1),
> -
> -	/*
> -	 * TLB 7:	4M	Non-cacheable, guarded
> -	 * 0xefc00000	4M	2nd half 8MB soldered FLASH
> -	 */
> -	SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH + 0x400000,
> -		      CONFIG_SYS_ALT_FLASH + 0x400000,
> -		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> -		      0, 7, BOOKE_PAGESZ_4M, 1),
> -#endif
> -
> -};
> -
> -int num_tlb_entries = ARRAY_SIZE(tlb_table);
> diff --git a/configs/sbc8548_PCI_33_PCIE_defconfig b/configs/sbc8548_PCI_33_PCIE_defconfig
> deleted file mode 100644
> index 3157ed92f396..000000000000
> --- a/configs/sbc8548_PCI_33_PCIE_defconfig
> +++ /dev/null
> @@ -1,42 +0,0 @@
> -CONFIG_PPC=y
> -CONFIG_SYS_TEXT_BASE=0xFFFA0000
> -CONFIG_ENV_SIZE=0x2000
> -CONFIG_ENV_SECT_SIZE=0x20000
> -CONFIG_MPC85xx=y
> -# CONFIG_CMD_ERRATA is not set
> -CONFIG_TARGET_SBC8548=y
> -CONFIG_OF_BOARD_SETUP=y
> -CONFIG_OF_STDOUT_VIA_ALIAS=y
> -CONFIG_SYS_EXTRA_OPTIONS="33,PCIE"
> -CONFIG_BOOTDELAY=10
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_BOARD_EARLY_INIT_F=y
> -# CONFIG_MISC_INIT_R is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_IMLS=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_PCI=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -# CONFIG_CMD_HASH is not set
> -# CONFIG_CMD_IRQ is not set
> -CONFIG_ENV_OVERWRITE=y
> -CONFIG_ENV_ADDR=0xFFFE0000
> -# CONFIG_MMC is not set
> -CONFIG_MTD_NOR_FLASH=y
> -CONFIG_FLASH_CFI_DRIVER=y
> -CONFIG_SYS_FLASH_CFI=y
> -CONFIG_PHY_ATHEROS=y
> -CONFIG_PHY_BROADCOM=y
> -CONFIG_PHY_DAVICOM=y
> -CONFIG_PHY_LXT=y
> -CONFIG_PHY_MARVELL=y
> -CONFIG_PHY_NATSEMI=y
> -CONFIG_PHY_REALTEK=y
> -CONFIG_PHY_SMSC=y
> -CONFIG_PHY_VITESSE=y
> -CONFIG_MII=y
> -CONFIG_TSEC_ENET=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_OF_LIBFDT=y
> diff --git a/configs/sbc8548_PCI_33_defconfig b/configs/sbc8548_PCI_33_defconfig
> deleted file mode 100644
> index ac4dbd04215b..000000000000
> --- a/configs/sbc8548_PCI_33_defconfig
> +++ /dev/null
> @@ -1,42 +0,0 @@
> -CONFIG_PPC=y
> -CONFIG_SYS_TEXT_BASE=0xFFFA0000
> -CONFIG_ENV_SIZE=0x2000
> -CONFIG_ENV_SECT_SIZE=0x20000
> -CONFIG_MPC85xx=y
> -# CONFIG_CMD_ERRATA is not set
> -CONFIG_TARGET_SBC8548=y
> -CONFIG_OF_BOARD_SETUP=y
> -CONFIG_OF_STDOUT_VIA_ALIAS=y
> -CONFIG_SYS_EXTRA_OPTIONS="33"
> -CONFIG_BOOTDELAY=10
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_BOARD_EARLY_INIT_F=y
> -# CONFIG_MISC_INIT_R is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_IMLS=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_PCI=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -# CONFIG_CMD_HASH is not set
> -# CONFIG_CMD_IRQ is not set
> -CONFIG_ENV_OVERWRITE=y
> -CONFIG_ENV_ADDR=0xFFFE0000
> -# CONFIG_MMC is not set
> -CONFIG_MTD_NOR_FLASH=y
> -CONFIG_FLASH_CFI_DRIVER=y
> -CONFIG_SYS_FLASH_CFI=y
> -CONFIG_PHY_ATHEROS=y
> -CONFIG_PHY_BROADCOM=y
> -CONFIG_PHY_DAVICOM=y
> -CONFIG_PHY_LXT=y
> -CONFIG_PHY_MARVELL=y
> -CONFIG_PHY_NATSEMI=y
> -CONFIG_PHY_REALTEK=y
> -CONFIG_PHY_SMSC=y
> -CONFIG_PHY_VITESSE=y
> -CONFIG_MII=y
> -CONFIG_TSEC_ENET=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_OF_LIBFDT=y
> diff --git a/configs/sbc8548_PCI_66_PCIE_defconfig b/configs/sbc8548_PCI_66_PCIE_defconfig
> deleted file mode 100644
> index b7cd900e5d8e..000000000000
> --- a/configs/sbc8548_PCI_66_PCIE_defconfig
> +++ /dev/null
> @@ -1,42 +0,0 @@
> -CONFIG_PPC=y
> -CONFIG_SYS_TEXT_BASE=0xFFFA0000
> -CONFIG_ENV_SIZE=0x2000
> -CONFIG_ENV_SECT_SIZE=0x20000
> -CONFIG_MPC85xx=y
> -# CONFIG_CMD_ERRATA is not set
> -CONFIG_TARGET_SBC8548=y
> -CONFIG_OF_BOARD_SETUP=y
> -CONFIG_OF_STDOUT_VIA_ALIAS=y
> -CONFIG_SYS_EXTRA_OPTIONS="66,PCIE"
> -CONFIG_BOOTDELAY=10
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_BOARD_EARLY_INIT_F=y
> -# CONFIG_MISC_INIT_R is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_IMLS=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_PCI=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -# CONFIG_CMD_HASH is not set
> -# CONFIG_CMD_IRQ is not set
> -CONFIG_ENV_OVERWRITE=y
> -CONFIG_ENV_ADDR=0xFFFE0000
> -# CONFIG_MMC is not set
> -CONFIG_MTD_NOR_FLASH=y
> -CONFIG_FLASH_CFI_DRIVER=y
> -CONFIG_SYS_FLASH_CFI=y
> -CONFIG_PHY_ATHEROS=y
> -CONFIG_PHY_BROADCOM=y
> -CONFIG_PHY_DAVICOM=y
> -CONFIG_PHY_LXT=y
> -CONFIG_PHY_MARVELL=y
> -CONFIG_PHY_NATSEMI=y
> -CONFIG_PHY_REALTEK=y
> -CONFIG_PHY_SMSC=y
> -CONFIG_PHY_VITESSE=y
> -CONFIG_MII=y
> -CONFIG_TSEC_ENET=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_OF_LIBFDT=y
> diff --git a/configs/sbc8548_PCI_66_defconfig b/configs/sbc8548_PCI_66_defconfig
> deleted file mode 100644
> index eb3c56b47b07..000000000000
> --- a/configs/sbc8548_PCI_66_defconfig
> +++ /dev/null
> @@ -1,42 +0,0 @@
> -CONFIG_PPC=y
> -CONFIG_SYS_TEXT_BASE=0xFFFA0000
> -CONFIG_ENV_SIZE=0x2000
> -CONFIG_ENV_SECT_SIZE=0x20000
> -CONFIG_MPC85xx=y
> -# CONFIG_CMD_ERRATA is not set
> -CONFIG_TARGET_SBC8548=y
> -CONFIG_OF_BOARD_SETUP=y
> -CONFIG_OF_STDOUT_VIA_ALIAS=y
> -CONFIG_SYS_EXTRA_OPTIONS="66"
> -CONFIG_BOOTDELAY=10
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_BOARD_EARLY_INIT_F=y
> -# CONFIG_MISC_INIT_R is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_IMLS=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_PCI=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -# CONFIG_CMD_HASH is not set
> -# CONFIG_CMD_IRQ is not set
> -CONFIG_ENV_OVERWRITE=y
> -CONFIG_ENV_ADDR=0xFFFE0000
> -# CONFIG_MMC is not set
> -CONFIG_MTD_NOR_FLASH=y
> -CONFIG_FLASH_CFI_DRIVER=y
> -CONFIG_SYS_FLASH_CFI=y
> -CONFIG_PHY_ATHEROS=y
> -CONFIG_PHY_BROADCOM=y
> -CONFIG_PHY_DAVICOM=y
> -CONFIG_PHY_LXT=y
> -CONFIG_PHY_MARVELL=y
> -CONFIG_PHY_NATSEMI=y
> -CONFIG_PHY_REALTEK=y
> -CONFIG_PHY_SMSC=y
> -CONFIG_PHY_VITESSE=y
> -CONFIG_MII=y
> -CONFIG_TSEC_ENET=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_OF_LIBFDT=y
> diff --git a/configs/sbc8548_defconfig b/configs/sbc8548_defconfig
> deleted file mode 100644
> index 6e38d9257969..000000000000
> --- a/configs/sbc8548_defconfig
> +++ /dev/null
> @@ -1,41 +0,0 @@
> -CONFIG_PPC=y
> -CONFIG_SYS_TEXT_BASE=0xFFFA0000
> -CONFIG_ENV_SIZE=0x2000
> -CONFIG_ENV_SECT_SIZE=0x20000
> -CONFIG_MPC85xx=y
> -# CONFIG_CMD_ERRATA is not set
> -CONFIG_TARGET_SBC8548=y
> -CONFIG_OF_BOARD_SETUP=y
> -CONFIG_OF_STDOUT_VIA_ALIAS=y
> -CONFIG_BOOTDELAY=10
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_BOARD_EARLY_INIT_F=y
> -# CONFIG_MISC_INIT_R is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_IMLS=y
> -CONFIG_CMD_I2C=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -# CONFIG_CMD_HASH is not set
> -# CONFIG_CMD_IRQ is not set
> -CONFIG_ENV_OVERWRITE=y
> -CONFIG_ENV_ADDR=0xFFFE0000
> -# CONFIG_MMC is not set
> -CONFIG_MTD_NOR_FLASH=y
> -CONFIG_FLASH_CFI_DRIVER=y
> -CONFIG_SYS_FLASH_CFI=y
> -CONFIG_PHY_ATHEROS=y
> -CONFIG_PHY_BROADCOM=y
> -CONFIG_PHY_DAVICOM=y
> -CONFIG_PHY_LXT=y
> -CONFIG_PHY_MARVELL=y
> -CONFIG_PHY_NATSEMI=y
> -CONFIG_PHY_REALTEK=y
> -CONFIG_PHY_SMSC=y
> -CONFIG_PHY_VITESSE=y
> -CONFIG_MII=y
> -CONFIG_TSEC_ENET=y
> -# CONFIG_PCI is not set
> -CONFIG_SYS_NS16550=y
> -CONFIG_OF_LIBFDT=y
> diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
> deleted file mode 100644
> index 6e26d456ab74..000000000000
> --- a/include/configs/sbc8548.h
> +++ /dev/null
> @@ -1,540 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright 2007,2009 Wind River Systems <www.windriver.com>
> - * Copyright 2007 Embedded Specialties, Inc.
> - * Copyright 2004, 2007 Freescale Semiconductor.
> - */
> -
> -/*
> - * sbc8548 board configuration file
> - * Please refer to board/sbc8548/README for more info.
> - */
> -#ifndef __CONFIG_H
> -#define __CONFIG_H
> -
> -#include <linux/stringify.h>
> -
> -/*
> - * Top level Makefile configuration choices
> - */
> -#ifdef CONFIG_PCI
> -#define CONFIG_PCI_INDIRECT_BRIDGE
> -#define CONFIG_PCI1
> -#endif
> -
> -#ifdef CONFIG_66
> -#define CONFIG_SYS_CLK_DIV 1
> -#endif
> -
> -#ifdef CONFIG_33
> -#define CONFIG_SYS_CLK_DIV 2
> -#endif
> -
> -#ifdef CONFIG_PCIE
> -#define CONFIG_PCIE1
> -#endif
> -
> -/*
> - * High Level Configuration Options
> - */
> -
> -/*
> - * If you want to boot from the SODIMM flash, instead of the soldered
> - * on flash, set this, and change JP12, SW2:8 accordingly.
> - */
> -#undef CONFIG_SYS_ALT_BOOT
> -
> -#undef CONFIG_RIO
> -
> -#ifdef CONFIG_PCI
> -#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
> -#define CONFIG_SYS_PCI_64BIT    1	/* enable 64-bit PCI resources */
> -#endif
> -
> -#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
> -
> -/*
> - * Below assumes that CCB:SYSCLK remains unchanged at 6:1 via SW2:[1-4]
> - */
> -#ifndef CONFIG_SYS_CLK_DIV
> -#define CONFIG_SYS_CLK_DIV	1	/* 2, if 33MHz PCI card installed */
> -#endif
> -#define CONFIG_SYS_CLK_FREQ	(66000000 / CONFIG_SYS_CLK_DIV)
> -
> -/*
> - * These can be toggled for performance analysis, otherwise use default.
> - */
> -#define CONFIG_L2_CACHE			/* toggle L2 cache */
> -#define CONFIG_BTB			/* toggle branch predition */
> -
> -/*
> - * Only possible on E500 Version 2 or newer cores.
> - */
> -#define CONFIG_ENABLE_36BIT_PHYS	1
> -
> -#undef	CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
> -
> -#define CONFIG_SYS_CCSRBAR		0xe0000000
> -#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
> -
> -/* DDR Setup */
> -#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
> -/*
> - * A hardware errata caused the LBC SDRAM SPD and the DDR2 SPD
> - * to collide, meaning you couldn't reliably read either. So
> - * physically remove the LBC PC100 SDRAM module from the board
> - * before enabling the two SPD options below, or check that you
> - * have the hardware fix on your board via "i2c probe" and looking
> - * for a device at 0x53.
> - */
> -#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
> -#undef CONFIG_DDR_SPD
> -
> -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
> -#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
> -
> -#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
> -#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
> -#define CONFIG_VERY_BIG_RAM
> -
> -#define CONFIG_DIMM_SLOTS_PER_CTLR	1
> -#define CONFIG_CHIP_SELECTS_PER_CTRL	2
> -
> -/*
> - * The hardware fix for the I2C address collision puts the DDR
> - * SPD at 0x53, but if we are running on an older board w/o the
> - * fix, it will still be at 0x51.  We check 0x53 1st.
> - */
> -#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
> -#define ALT_SPD_EEPROM_ADDRESS	0x53	/* CTLR 0 DIMM 0 */
> -
> -/*
> - * Make sure required options are set
> - */
> -#ifndef CONFIG_SPD_EEPROM
> -	#define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256MB */
> -	#define CONFIG_SYS_DDR_CONTROL	0xc300c000
> -#endif
> -
> -/*
> - * FLASH on the Local Bus
> - * Two banks, one 8MB the other 64MB, using the CFI driver.
> - * JP12+SW2.8 are used to swap CS0 and CS6, defaults are to have
> - * CS0 the 8MB boot flash, and CS6 the 64MB flash.
> - *
> - *	Default:
> - *	ec00_0000	efff_ffff	64MB SODIMM
> - *	ff80_0000	ffff_ffff	8MB soldered flash
> - *
> - *	Alternate:
> - *	ef80_0000	efff_ffff	8MB soldered flash
> - *	fc00_0000	ffff_ffff	64MB SODIMM
> - *
> - * BR0_8M:
> - *    Base address 0 = 0xff80_0000 = BR0[0:16] = 1111 1111 1000 0000 0
> - *    Port Size = 8 bits = BRx[19:20] = 01
> - *    Use GPCM = BRx[24:26] = 000
> - *    Valid = BRx[31] = 1
> - *
> - * BR0_64M:
> - *    Base address 0 = 0xfc00_0000 = BR0[0:16] = 1111 1100 0000 0000 0
> - *    Port Size = 32 bits = BRx[19:20] = 11
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801    BR0_8M
> - * 1111 1100 0000 0000 0001 1000 0000 0001 = fc001801    BR0_64M
> - */
> -#define CONFIG_SYS_BR0_8M	0xff800801
> -#define CONFIG_SYS_BR0_64M	0xfc001801
> -
> -/*
> - * BR6_8M:
> - *    Base address 6 = 0xef80_0000 = BR6[0:16] = 1110 1111 1000 0000 0
> - *    Port Size = 8 bits = BRx[19:20] = 01
> - *    Use GPCM = BRx[24:26] = 000
> - *    Valid = BRx[31] = 1
> -
> - * BR6_64M:
> - *    Base address 6 = 0xec00_0000 = BR6[0:16] = 1110 1100 0000 0000 0
> - *    Port Size = 32 bits = BRx[19:20] = 11
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1110 1111 1000 0000 0000 1000 0000 0001 = ef800801    BR6_8M
> - * 1110 1100 0000 0000 0001 1000 0000 0001 = ec001801    BR6_64M
> - */
> -#define CONFIG_SYS_BR6_8M	0xef800801
> -#define CONFIG_SYS_BR6_64M	0xec001801
> -
> -/*
> - * OR0_8M:
> - *    Addr Mask = 8M = OR1[0:16] = 1111 1111 1000 0000 0
> - *    XAM = OR0[17:18] = 11
> - *    CSNT = OR0[20] = 1
> - *    ACS = half cycle delay = OR0[21:22] = 11
> - *    SCY = 6 = OR0[24:27] = 0110
> - *    TRLX = use relaxed timing = OR0[29] = 1
> - *    EAD = use external address latch delay = OR0[31] = 1
> - *
> - * OR0_64M:
> - *    Addr Mask = 64M = OR1[0:16] = 1111 1100 0000 0000 0
> - *
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    OR0_8M
> - * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65    OR0_64M
> - */
> -#define CONFIG_SYS_OR0_8M	0xff806e65
> -#define CONFIG_SYS_OR0_64M	0xfc006e65
> -
> -/*
> - * OR6_8M:
> - *    Addr Mask = 8M = OR6[0:16] = 1111 1111 1000 0000 0
> - *    XAM = OR6[17:18] = 11
> - *    CSNT = OR6[20] = 1
> - *    ACS = half cycle delay = OR6[21:22] = 11
> - *    SCY = 6 = OR6[24:27] = 0110
> - *    TRLX = use relaxed timing = OR6[29] = 1
> - *    EAD = use external address latch delay = OR6[31] = 1
> - *
> - * OR6_64M:
> - *    Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    OR6_8M
> - * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65    OR6_64M
> - */
> -#define CONFIG_SYS_OR6_8M	0xff806e65
> -#define CONFIG_SYS_OR6_64M	0xfc006e65
> -
> -#ifndef CONFIG_SYS_ALT_BOOT		/* JP12 in default position */
> -#define CONFIG_SYS_BOOT_BLOCK		0xff800000	/* start of 8MB Flash */
> -#define CONFIG_SYS_ALT_FLASH		0xec000000	/* 64MB "user" flash */
> -
> -#define CONFIG_SYS_BR0_PRELIM		CONFIG_SYS_BR0_8M
> -#define CONFIG_SYS_OR0_PRELIM		CONFIG_SYS_OR0_8M
> -
> -#define CONFIG_SYS_BR6_PRELIM		CONFIG_SYS_BR6_64M
> -#define CONFIG_SYS_OR6_PRELIM		CONFIG_SYS_OR6_64M
> -#else					/* JP12 in alternate position */
> -#define CONFIG_SYS_BOOT_BLOCK		0xfc000000	/* start 64MB Flash */
> -#define CONFIG_SYS_ALT_FLASH		0xef800000	/* 8MB soldered flash */
> -
> -#define CONFIG_SYS_BR0_PRELIM		CONFIG_SYS_BR0_64M
> -#define CONFIG_SYS_OR0_PRELIM		CONFIG_SYS_OR0_64M
> -
> -#define CONFIG_SYS_BR6_PRELIM		CONFIG_SYS_BR6_8M
> -#define CONFIG_SYS_OR6_PRELIM		CONFIG_SYS_OR6_8M
> -#endif
> -
> -#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_BOOT_BLOCK
> -#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, \
> -					 CONFIG_SYS_ALT_FLASH}
> -#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
> -#define CONFIG_SYS_MAX_FLASH_SECT	256		/* sectors per device */
> -#undef	CONFIG_SYS_FLASH_CHECKSUM
> -#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
> -#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
> -
> -#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
> -
> -#define CONFIG_SYS_FLASH_EMPTY_INFO
> -
> -/* CS5 = Local bus peripherals controlled by the EPLD */
> -
> -#define CONFIG_SYS_BR5_PRELIM		0xf8000801
> -#define CONFIG_SYS_OR5_PRELIM		0xff006e65
> -#define CONFIG_SYS_EPLD_BASE		0xf8000000
> -#define CONFIG_SYS_LED_DISP_BASE	0xf8000000
> -#define CONFIG_SYS_USER_SWITCHES_BASE	0xf8100000
> -#define CONFIG_SYS_BD_REV		0xf8300000
> -#define CONFIG_SYS_EEPROM_BASE		0xf8b00000
> -
> -/*
> - * SDRAM on the Local Bus (CS3 and CS4)
> - * Note that most boards have a hardware errata where both the
> - * LBC SDRAM and the DDR2 SDRAM decode at 0x51, making it impossible
> - * to use CONFIG_DDR_SPD unless you physically remove the LBC DIMM.
> - * A hardware workaround is also available, see README.sbc8548 file.
> - */
> -#define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
> -#define CONFIG_SYS_LBC_SDRAM_SIZE	128		/* LBC SDRAM is 128MB */
> -
> -/*
> - * Base Register 3 and Option Register 3 configure the 1st 1/2 SDRAM.
> - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
> - *
> - * For BR3, need:
> - *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
> - *    port-size = 32-bits = BR2[19:20] = 11
> - *    no parity checking = BR2[21:22] = 00
> - *    SDRAM for MSEL = BR2[24:26] = 011
> - *    Valid = BR[31] = 1
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
> - *
> - */
> -
> -#define CONFIG_SYS_BR3_PRELIM		0xf0001861
> -
> -/*
> - * The SDRAM size in MB, of 1/2 CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
> - *
> - * For OR3, need:
> - *    64MB mask for AM, OR3[0:7] = 1111 1100
> - *		   XAM, OR3[17:18] = 11
> - *    10 columns OR3[19-21] = 011
> - *    12 rows   OR3[23-25] = 011
> - *    EAD set for extra time OR[31] = 0
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0
> - */
> -
> -#define CONFIG_SYS_OR3_PRELIM		0xfc006cc0
> -
> -/*
> - * Base Register 4 and Option Register 4 configure the 2nd 1/2 SDRAM.
> - * The base address, (SDRAM_BASE + 1/2*SIZE), is 0xf4000000.
> - *
> - * For BR4, need:
> - *    Base address of 0xf4000000 = BR[0:16] = 1111 0100 0000 0000 0
> - *    port-size = 32-bits = BR2[19:20] = 11
> - *    no parity checking = BR2[21:22] = 00
> - *    SDRAM for MSEL = BR2[24:26] = 011
> - *    Valid = BR[31] = 1
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 0000 0000 0000 0001 1000 0110 0001 = f4001861
> - *
> - */
> -
> -#define CONFIG_SYS_BR4_PRELIM		0xf4001861
> -
> -/*
> - * The SDRAM size in MB, of 1/2 CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
> - *
> - * For OR4, need:
> - *    64MB mask for AM, OR3[0:7] = 1111 1100
> - *		   XAM, OR3[17:18] = 11
> - *    10 columns OR3[19-21] = 011
> - *    12 rows   OR3[23-25] = 011
> - *    EAD set for extra time OR[31] = 0
> - *
> - * 0    4    8    12   16   20   24   28
> - * 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0
> - */
> -
> -#define CONFIG_SYS_OR4_PRELIM		0xfc006cc0
> -
> -#define CONFIG_SYS_LBC_LCRR		0x00000002    /* LB clock ratio reg */
> -#define CONFIG_SYS_LBC_LBCR		0x00000000    /* LB config reg */
> -#define CONFIG_SYS_LBC_LSRT		0x20000000  /* LB sdram refresh timer */
> -#define CONFIG_SYS_LBC_MRTPR		0x00000000  /* LB refresh timer prescal*/
> -
> -/*
> - * Common settings for all Local Bus SDRAM commands.
> - */
> -#define CONFIG_SYS_LBC_LSDMR_COMMON	( LSDMR_RFCR16		\
> -				| LSDMR_BSMA1516	\
> -				| LSDMR_PRETOACT3	\
> -				| LSDMR_ACTTORW3	\
> -				| LSDMR_BUFCMD		\
> -				| LSDMR_BL8		\
> -				| LSDMR_WRC2		\
> -				| LSDMR_CL3		\
> -				)
> -
> -#define CONFIG_SYS_LBC_LSDMR_PCHALL	\
> -	 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
> -#define CONFIG_SYS_LBC_LSDMR_ARFRSH	\
> -	 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
> -#define CONFIG_SYS_LBC_LSDMR_MRW	\
> -	 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
> -#define CONFIG_SYS_LBC_LSDMR_RFEN	\
> -	 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_RFEN)
> -
> -#define CONFIG_SYS_INIT_RAM_LOCK	1
> -#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
> -#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
> -
> -#define CONFIG_SYS_INIT_L2_ADDR	0xf8f80000	/* relocate boot L2SRAM */
> -
> -#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> -#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
> -
> -/*
> - * For soldered on flash, (128kB/sector) we use 2 sectors for u-boot and
> - * one for env+bootpg (CONFIG_SYS_TEXT_BASE=0xfffa_0000, 384kB total).  For SODIMM
> - * flash (512kB/sector) we use 1 sector for u-boot, and one for env+bootpg
> - * (CONFIG_SYS_TEXT_BASE=0xfff0_0000, 1MB total).  This dynamically sets the right
> - * thing for MONITOR_LEN in both cases.
> - */
> -#define CONFIG_SYS_MONITOR_LEN		(~CONFIG_SYS_TEXT_BASE + 1)
> -#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024) /* Reserved for malloc */
> -
> -/* Serial Port */
> -#define CONFIG_SYS_NS16550_SERIAL
> -#define CONFIG_SYS_NS16550_REG_SIZE	1
> -#define CONFIG_SYS_NS16550_CLK		(400000000 / CONFIG_SYS_CLK_DIV)
> -
> -#define CONFIG_SYS_BAUDRATE_TABLE \
> -	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
> -
> -#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
> -#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
> -
> -/*
> - * I2C
> - */
> -#define CONFIG_SYS_I2C
> -#define CONFIG_SYS_I2C_FSL
> -#define CONFIG_SYS_FSL_I2C_SPEED	400000
> -#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
> -#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
> -#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
> -
> -/*
> - * General PCI
> - * Memory space is mapped 1-1, but I/O space must start from 0.
> - */
> -#define CONFIG_SYS_PCI_VIRT		0x80000000	/* 1G PCI TLB */
> -#define CONFIG_SYS_PCI_PHYS		0x80000000	/* 1G PCI TLB */
> -
> -#define CONFIG_SYS_PCI1_MEM_VIRT	0x80000000
> -#define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
> -#define CONFIG_SYS_PCI1_MEM_PHYS	0x80000000
> -#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
> -#define CONFIG_SYS_PCI1_IO_VIRT		0xe2000000
> -#define CONFIG_SYS_PCI1_IO_BUS		0x00000000
> -#define CONFIG_SYS_PCI1_IO_PHYS		0xe2000000
> -#define CONFIG_SYS_PCI1_IO_SIZE		0x00800000	/* 8M */
> -
> -#ifdef CONFIG_PCIE1
> -#define CONFIG_SYS_PCIE1_MEM_VIRT	0xa0000000
> -#define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
> -#define CONFIG_SYS_PCIE1_MEM_PHYS	0xa0000000
> -#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
> -#define CONFIG_SYS_PCIE1_IO_VIRT	0xe2800000
> -#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
> -#define CONFIG_SYS_PCIE1_IO_PHYS	0xe2800000
> -#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
> -#endif
> -
> -#ifdef CONFIG_RIO
> -/*
> - * RapidIO MMU
> - */
> -#define CONFIG_SYS_RIO_MEM_BASE	0xC0000000
> -#define CONFIG_SYS_RIO_MEM_SIZE	0x20000000	/* 512M */
> -#endif
> -
> -#if defined(CONFIG_PCI)
> -
> -#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
> -
> -#endif	/* CONFIG_PCI */
> -
> -#if defined(CONFIG_TSEC_ENET)
> -
> -#define CONFIG_TSEC1	1
> -#define CONFIG_TSEC1_NAME	"eTSEC0"
> -#define CONFIG_TSEC2	1
> -#define CONFIG_TSEC2_NAME	"eTSEC1"
> -#undef CONFIG_MPC85XX_FEC
> -
> -#define TSEC1_PHY_ADDR		0x19
> -#define TSEC2_PHY_ADDR		0x1a
> -
> -#define TSEC1_PHYIDX		0
> -#define TSEC2_PHYIDX		0
> -
> -#define TSEC1_FLAGS		TSEC_GIGABIT
> -#define TSEC2_FLAGS		TSEC_GIGABIT
> -
> -/* Options are: eTSEC[0-3] */
> -#define CONFIG_ETHPRIME		"eTSEC0"
> -#endif	/* CONFIG_TSEC_ENET */
> -
> -#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
> -#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
> -
> -/*
> - * BOOTP options
> - */
> -#define CONFIG_BOOTP_BOOTFILESIZE
> -
> -#undef CONFIG_WATCHDOG			/* watchdog disabled */
> -
> -/*
> - * Miscellaneous configurable options
> - */
> -#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
> -
> -/*
> - * For booting Linux, the board info and command line data
> - * have to be in the first 8 MB of memory, since this is
> - * the maximum mapped by the Linux kernel during initialization.
> - */
> -#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
> -
> -#if defined(CONFIG_CMD_KGDB)
> -#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
> -#endif
> -
> -/*
> - * Environment Configuration
> - */
> -#if defined(CONFIG_TSEC_ENET)
> -#define CONFIG_HAS_ETH0
> -#define CONFIG_HAS_ETH1
> -#endif
> -
> -#define CONFIG_IPADDR	 192.168.0.55
> -
> -#define CONFIG_HOSTNAME	 "sbc8548"
> -#define CONFIG_ROOTPATH	 "/opt/eldk/ppc_85xx"
> -#define CONFIG_BOOTFILE	 "/uImage"
> -#define CONFIG_UBOOTPATH /u-boot.bin	/* TFTP server */
> -
> -#define CONFIG_SERVERIP	 192.168.0.2
> -#define CONFIG_GATEWAYIP 192.168.0.1
> -#define CONFIG_NETMASK	 255.255.255.0
> -
> -#define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
> -
> -#define	CONFIG_EXTRA_ENV_SETTINGS				\
> -"netdev=eth0\0"						\
> -"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"				\
> -"tftpflash=tftpboot $loadaddr $uboot; "			\
> -	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
> -	"erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
> -	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
> -	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
> -	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
> -"consoledev=ttyS0\0"				\
> -"ramdiskaddr=2000000\0"			\
> -"ramdiskfile=uRamdisk\0"			\
> -"fdtaddr=1e00000\0"				\
> -"fdtfile=sbc8548.dtb\0"
> -
> -#define CONFIG_NFSBOOTCOMMAND						\
> -   "setenv bootargs root=/dev/nfs rw "					\
> -      "nfsroot=$serverip:$rootpath "					\
> -      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
> -      "console=$consoledev,$baudrate $othbootargs;"			\
> -   "tftp $loadaddr $bootfile;"						\
> -   "tftp $fdtaddr $fdtfile;"						\
> -   "bootm $loadaddr - $fdtaddr"
> -
> -#define CONFIG_RAMBOOTCOMMAND \
> -   "setenv bootargs root=/dev/ram rw "					\
> -      "console=$consoledev,$baudrate $othbootargs;"			\
> -   "tftp $ramdiskaddr $ramdiskfile;"					\
> -   "tftp $loadaddr $bootfile;"						\
> -   "tftp $fdtaddr $fdtfile;"						\
> -   "bootm $loadaddr $ramdiskaddr $fdtaddr"
> -
> -#define CONFIG_BOOTCOMMAND	CONFIG_RAMBOOTCOMMAND
> -
> -#endif	/* __CONFIG_H */
> -- 
> 2.17.1
> 


More information about the U-Boot mailing list