[PATCH v2] imx: Add SeeedStudio NPI-IMX6ULL Support

Navin Sankar Velliangiri navin at linumiz.com
Tue May 18 05:33:20 CEST 2021


CPU:   Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 49C
Reset cause: POR
Model: Seeed NPi iMX6ULL Dev Board with NAND
Board: Seeed NPi i.MX6ULL Dev Board
DRAM:  512 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial at 2020000
Out:   serial at 2020000
Err:   serial at 2020000
Net:   FEC0

Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host

Signed-off-by: Navin Sankar Velliangiri <navin at linumiz.com>

Note:

Changes in v2:

 * removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file.
 * Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation.
---
 arch/arm/Kconfig                              |   1 +
 arch/arm/dts/Makefile                         |   1 +
 .../imx6ull-seeed-npi-imx6ull-dev-board.dts   |  19 ++
 .../dts/imx6ull-seeed-npi-imx6ull-u-boot.dtsi |  24 ++
 arch/arm/dts/imx6ull-seeed-npi-imx6ull.dtsi   | 271 ++++++++++++++++++
 arch/arm/mach-imx/mx6/Kconfig                 |  11 +
 board/seeed/npi_imx6ull/Kconfig               |  12 +
 board/seeed/npi_imx6ull/MAINTAINERS           |   9 +
 board/seeed/npi_imx6ull/Makefile              |   4 +
 board/seeed/npi_imx6ull/README                |  61 ++++
 board/seeed/npi_imx6ull/npi_imx6ull.c         | 114 ++++++++
 board/seeed/npi_imx6ull/spl.c                 | 205 +++++++++++++
 configs/seeed_npi_imx6ull_defconfig           |  80 ++++++
 include/configs/npi_imx6ull.h                 |  96 +++++++
 14 files changed, 908 insertions(+)
 create mode 100644 arch/arm/dts/imx6ull-seeed-npi-imx6ull-dev-board.dts
 create mode 100644 arch/arm/dts/imx6ull-seeed-npi-imx6ull-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx6ull-seeed-npi-imx6ull.dtsi
 create mode 100644 board/seeed/npi_imx6ull/Kconfig
 create mode 100644 board/seeed/npi_imx6ull/MAINTAINERS
 create mode 100644 board/seeed/npi_imx6ull/Makefile
 create mode 100644 board/seeed/npi_imx6ull/README
 create mode 100644 board/seeed/npi_imx6ull/npi_imx6ull.c
 create mode 100644 board/seeed/npi_imx6ull/spl.c
 create mode 100644 configs/seeed_npi_imx6ull_defconfig
 create mode 100644 include/configs/npi_imx6ull.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 31d687ea01..3c46f3ff39 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -2008,6 +2008,7 @@ source "board/hisilicon/poplar/Kconfig"
 source "board/isee/igep003x/Kconfig"
 source "board/kontron/sl28/Kconfig"
 source "board/myir/mys_6ulx/Kconfig"
+source "board/seeed/npi_imx6ull/Kconfig"
 source "board/spear/spear300/Kconfig"
 source "board/spear/spear310/Kconfig"
 source "board/spear/spear320/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index aec5020a0f..6cbaafcc73 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -798,6 +798,7 @@ dtb-$(CONFIG_MX6ULL) += \
 	imx6ull-14x14-evk.dtb \
 	imx6ull-colibri.dtb \
 	imx6ull-myir-mys-6ulx-eval.dtb \
+	imx6ull-seeed-npi-imx6ull-dev-board.dtb \
 	imx6ull-phytec-segin-ff-rdk-emmc.dtb \
 	imx6ull-dart-6ul.dtb \
 	imx6ull-somlabs-visionsom.dtb \
diff --git a/arch/arm/dts/imx6ull-seeed-npi-imx6ull-dev-board.dts b/arch/arm/dts/imx6ull-seeed-npi-imx6ull-dev-board.dts
new file mode 100644
index 0000000000..ce03ddfd21
--- /dev/null
+++ b/arch/arm/dts/imx6ull-seeed-npi-imx6ull-dev-board.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021 Linumiz
+ * Author: Navin Sankar Velliangiri <navin at linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-seeed-npi-imx6ull.dtsi"
+#include "imx6ull-seeed-npi-imx6ull-u-boot.dtsi"
+
+/ {
+	model = "Seeed NPi iMX6ULL Dev Board with NAND";
+	compatible = "seeed,imx6ull-seeed-npi-imx6ull", "fsl,imx6ull";
+};
+
+&gpmi {
+	status = "okay";
+};
diff --git a/arch/arm/dts/imx6ull-seeed-npi-imx6ull-u-boot.dtsi b/arch/arm/dts/imx6ull-seeed-npi-imx6ull-u-boot.dtsi
new file mode 100644
index 0000000000..054e1aa94b
--- /dev/null
+++ b/arch/arm/dts/imx6ull-seeed-npi-imx6ull-u-boot.dtsi
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021 Linumiz
+ * Author: Navin Sankar Velliangiri <navin at linumiz.com>
+ */
+
+&pinctrl_uart1 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpmi {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&usdhc1 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&usdhc2 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/imx6ull-seeed-npi-imx6ull.dtsi b/arch/arm/dts/imx6ull-seeed-npi-imx6ull.dtsi
new file mode 100644
index 0000000000..b019474dba
--- /dev/null
+++ b/arch/arm/dts/imx6ull-seeed-npi-imx6ull.dtsi
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021 Linumiz
+ * Author: Navin Sankar Velliangiri <navin at linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Seeed NPi-iMX6ULL Dev Board";
+	compatible = "fsl,imx6ull";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user-led {
+			label = "User";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_gpios>;
+			gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-name = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	keep-power-in-suspend;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 2 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <2>;
+			micrel,led-mode = <1>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+
+		ethphy1: ethernet-phy at 1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			micrel,led-mode = <1>;
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpios>;
+
+	pinctrl_uart1: uart1grp {
+		fsl,pin = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pin = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__RAWNAND_DQS		0x0b0b1
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
+			MX6UL_PAD_NAND_CE1_B__RAWNAND_CE1_B	0x0b0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06   0x0b0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170b9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170b9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170b9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b031
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO        0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2  0x4001b031
+		>;
+	};
+
+	pinctrl_gpios: gpiosgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x0b0b0
+		>;
+	};
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 9450e6a683..c313698423 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -453,6 +453,17 @@ config TARGET_NITROGEN6X
 	imply USB_ETHER_SMSC95XX
 	imply USB_HOST_ETHER
 
+config TARGET_NPI_IMX6ULL
+	bool "Seeed NPI-IMX6ULL"
+	depends on MX6ULL
+	select DM
+	select DM_ETH
+	select DM_MMC
+	select DM_GPIO
+	select DM_SERIAL
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 config TARGET_OPOS6ULDEV
 	bool "Armadeus OPOS6ULDev board"
 	depends on MX6UL
diff --git a/board/seeed/npi_imx6ull/Kconfig b/board/seeed/npi_imx6ull/Kconfig
new file mode 100644
index 0000000000..5e298299a3
--- /dev/null
+++ b/board/seeed/npi_imx6ull/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NPI_IMX6ULL
+
+config SYS_BOARD
+	default "npi_imx6ull"
+
+config SYS_VENDOR
+	default "seeed"
+
+config SYS_CONFIG_NAME
+	default "npi_imx6ull"
+
+endif
diff --git a/board/seeed/npi_imx6ull/MAINTAINERS b/board/seeed/npi_imx6ull/MAINTAINERS
new file mode 100644
index 0000000000..c6a915c79b
--- /dev/null
+++ b/board/seeed/npi_imx6ull/MAINTAINERS
@@ -0,0 +1,9 @@
+NPI_IMX6ULL BOARD
+M:	Navin Sankar Velliangiri <navin at linumiz.com>
+S:	Maintained
+F:	arch/arm/dts/imx6ull-seeed-npi-imx6ull-dev-board.dts
+F:	arch/arm/dts/imx6ull-seeed-npi-imx6ull-u-boot.dtsi
+F:	arch/arm/dts/imx6ull-seeed-npi-imx6ull.dtsi
+F:	board/seeed/npi-imx6ull/
+F:	configs/seeed_npi_imx6ull_defconfig
+F:	include/configs/npi_imx6ull.h
diff --git a/board/seeed/npi_imx6ull/Makefile b/board/seeed/npi_imx6ull/Makefile
new file mode 100644
index 0000000000..93ea413517
--- /dev/null
+++ b/board/seeed/npi_imx6ull/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier:	GPL-2.0+
+
+obj-y	:= npi_imx6ull.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/seeed/npi_imx6ull/README b/board/seeed/npi_imx6ull/README
new file mode 100644
index 0000000000..01d218a9bc
--- /dev/null
+++ b/board/seeed/npi_imx6ull/README
@@ -0,0 +1,61 @@
+How to use U-BOOT on SeeedStudio NPI-IMX6ULL Single Board Computer
+------------------------------------------------------------------
+
+- Configure and build U-Boot for NPI-IMX6ULL:
+
+    $ export ARCH=arm
+    $ export CROSS_COMPILE=arm-none-linux-gnueabihf-
+    $ make seeed_npi_imx6ull_defconfig
+    $ make
+
+This will generate SPL and u-boot-dtb.img images.
+
+Boot from MMC/SD:
+- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
+
+    $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+  Boot switch position: SW1 -> 0
+			SW2 -> 1
+			SW3 -> 0
+			SW4 -> 0
+			SW5 -> 1
+			SW6 -> 0
+			SW7 -> 0
+			SW8 -> 1
+
+Boot from NAND:
+- Boot the board using SD/MMC or Serial download and load the SPL into memory
+either from SD/MMC or TFTP.
+
+Default MTD layout is 512k(spl),1m(uboot),1m(uboot-dup),-(ubi)
+
+Flash SPL to NAND from SD/MMC,
+
+    $ ext4load mmc 0:2 $loadaddr SPL
+    $ nand erase.part spl
+    $ nandbcb init $loadaddr 0x0 $filesize
+
+Flash u-boot image to NAND from SD/MMC,
+
+    $ ext4load mmc 0:2 $loadaddr u-boot-dtb.img
+    $ nand erase.part uboot
+    $ nand write $loadaddr uboot $filesize
+
+- Boot mode settings:
+
+  Boot switch position: SW1 -> 0
+			SW2 -> 1
+			SW3 -> 1
+			SW4 -> 0
+			SW5 -> 0
+			SW6 -> 1
+			SW7 -> 0
+			SW8 -> 0
+
+- Connect the Serial cable to UART0 and the PC for the console.
+
+- Reset the board using reset button and U-Boot should boot from NAND.
diff --git a/board/seeed/npi_imx6ull/npi_imx6ull.c b/board/seeed/npi_imx6ull/npi_imx6ull.c
new file mode 100644
index 0000000000..eb9ee555c8
--- /dev/null
+++ b/board/seeed/npi_imx6ull/npi_imx6ull.c
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Linumiz
+ * Author: Navin Sankar Velliangiri <navin at linumiz.com>
+ */
+
+#include <init.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc_imx.h>
+#include <linux/bitops.h>
+#include <miiphy.h>
+#include <net.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE         | PAD_CTL_PUE       | \
+			PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+			PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | \
+			PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+#ifdef CONFIG_FEC_MXC
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	if (fec_id == 0) {
+		/*
+		 * Use 50MHz anatop loopback REF_CLK1 for ENET1,
+		 * clear gpr1[13], set gpr1[17].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+				IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+	} else {
+		/*
+		 * Use 50MHz anatop loopbak REF_CLK2 for ENET2,
+		 * clear gpr1[14], set gpr1[18].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+				IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+	}
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	printf("Board: Seeed NPi i.MX6ULL Dev Board\n");
+
+	return 0;
+}
diff --git a/board/seeed/npi_imx6ull/spl.c b/board/seeed/npi_imx6ull/spl.c
new file mode 100644
index 0000000000..4b56f52d98
--- /dev/null
+++ b/board/seeed/npi_imx6ull/spl.c
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Linumiz
+ * Author: Navin Sankar Velliangiri <navin at linumiz.com>
+ */
+
+#include <common.h>
+#include <init.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
+#include <fsl_esdhc_imx.h>
+
+/* Configuration for Micron MT41K256M16TW-107 32M x 16 x 8 -> 512MiB */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000030,
+	.dram_sdqs0 = 0x00000030,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0 = 0x41480148,
+	.p0_mprddlctl = 0x40403E42,
+	.p0_mpwrdlctl = 0x40405852,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,             /* Bus size = 16bit */
+	.cs_density = 32,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 1,
+	.rtt_nom = 1,
+	.walat = 1,             /* Write additional latency */
+	.ralat = 5,             /* Read additional latency */
+	.mif3_mode = 3,         /* Command prediction working mode */
+	.bi_on = 1,             /* Bank interleaving enabled */
+	.pd_fast_exit = 1,
+	.sde_to_rst = 0x10,
+	.rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
+	.ddr_type = DDR_TYPE_DDR3,
+	.refsel = 1,            /* Refresh cycles at 32KHz */
+	.refr = 7,              /* 8 refresh commands per refresh cycle */
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 1600,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+#ifdef CONFIG_FSL_ESDHC_IMX
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE         | PAD_CTL_PUE       | \
+			PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW | \
+			PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | \
+			PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{
+		.esdhc_base = USDHC1_BASE_ADDR,
+		.max_bus_width = 4,
+	},
+#ifndef CONFIG_NAND_MXS
+	{
+		.esdhc_base = USDHC2_BASE_ADDR,
+		.max_bus_width = 8,
+	},
+#endif
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1;
+}
+
+int board_mmc_init(struct bd_info *bis)
+{
+	int i, ret;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			SETUP_IOMUX_PADS(usdhc1_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#ifndef CONFIG_NAND_MXS
+		case 1:
+			SETUP_IOMUX_PADS(usdhc2_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#endif
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+#endif /* CONFIG_FSL_ESDHC_IMX */
+
+void board_init_f(ulong dummy)
+{
+	ccgr_init();
+
+	/* Setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* Setup iomux and fec */
+	board_early_init_f();
+
+	/* Setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+}
diff --git a/configs/seeed_npi_imx6ull_defconfig b/configs/seeed_npi_imx6ull_defconfig
new file mode 100644
index 0000000000..6503cabbd0
--- /dev/null
+++ b/configs/seeed_npi_imx6ull_defconfig
@@ -0,0 +1,80 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_ENV_SIZE=0x4000
+CONFIG_MX6ULL=y
+CONFIG_TARGET_NPI_IMX6ULL=y
+CONFIG_SPL_TEXT_BASE=0x908000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-seeed-npi-imx6ull-dev-board"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_DMA=y
+CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x80000000
+CONFIG_SYS_MEMTEST_END=0x90000000
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+# CONFIG_CMD_I2C is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
+CONFIG_MTDPARTS_DEFAULT="gpmi-nand:512k(spl),1m(uboot),1m(uboot-dup),-(ubi)"
+CONFIG_SYS_NAND_USE_FLASH_BBT=y
+CONFIG_CMD_UBI=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+# CONFIG_DM_I2C_GPIO is not set
+# CONFIG_SYS_I2C_MXC is not set
+CONFIG_FSL_USDHC=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND_MXS=y
+CONFIG_NAND_MXS_DT=y
+CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
+CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
+CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND=0x180000
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_PMIC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_MMC=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_OFFSET=0x3c00000
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_SMBIOS_MANUFACTURER="Seeed"
diff --git a/include/configs/npi_imx6ull.h b/include/configs/npi_imx6ull.h
new file mode 100644
index 0000000000..3be9b8ff55
--- /dev/null
+++ b/include/configs/npi_imx6ull.h
@@ -0,0 +1,96 @@
+/* SPDX-License-Identifier: GPL-2.0+
+ *
+ * Copyright (c) 2021 Linumiz
+ * Author: Navin Sankar Velliangiri <navin at linumiz.com>
+ */
+
+#ifndef _NPI_IMX6ULL_H
+#define _NPI_IMX6ULL_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+#define CONFIG_SYS_FSL_USDHC_NUM	1
+
+/* Size of malloc() poll */
+#define CONFIG_SYS_MALLOC_LEN		SZ_2M
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+
+#define CONFIG_NETMASK			255.255.255.0
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* environment settings */
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#elif defined(CONFIG_ENV_IS_IN_NAND)
+#undef CONFIG_ENV_SIZE
+#define CONFIG_ENV_SECT_SIZE		(128 << 10)
+#define CONFIG_ENV_SIZE			CONFIG_ENV_SECT_SIZE
+#endif
+
+/* NAND */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	1
+
+#ifdef CONFIG_CMD_NET
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR		0x1
+#define CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_ETHPRIME			"eth0"
+#endif
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_FEC_ENET_DEV		1
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console=ttymxc0,115200n8\0" \
+	"image=zImage\0" \
+	"fdtfile=imx6ull-seeed-npi-dev-board.dtb\0" \
+	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
+	"fdt_addr_r=0x82000000\0" \
+	"kernel_addr_r=0x81000000\0" \
+	"pxefile_addr_r=0x87100000\0" \
+	"ramdisk_addr_r=0x82100000\0" \
+	"scriptaddr=0x87000000\0" \
+	"root=/dev/mmcblk0p2 rootwait\0" \
+	BOOTENV
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(UBIFS, ubifs, 0) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#endif /* _NPI_IMX6ULL_H */
-- 
2.31.1



More information about the U-Boot mailing list