[PATCH v4 11/14] board: synquacer: Add DeveloperBox 96boards EE support

Masami Hiramatsu masami.hiramatsu at linaro.org
Wed May 19 07:46:22 CEST 2021


Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.

For more information, see this page;
  https://www.96boards.org/product/developerbox/

Signed-off-by: Masami Hiramatsu <masami.hiramatsu at linaro.org>
---
 Changes in v4:
  - Add I2C and RTC configuration.
  - Enable RTC and Date command.
  - Remove I2C0 node before booting linux to hide it same as EDK2 does.
  - Add some configurations to make it EBBR compliant.
 Changes in v3:
  - Enable CONFIG_MMC_SDHCI_F_SDH30.
  - Enable CONFIG_CMD_GENERIC (fstype command) for distro boot.
  - Remove unneeded CONFIG_ONLY_GENERIC_GPIO.
 Changes in v2:
  - Do not include arch/gpio.h and remove arch-sc2a11/gpio.h.
  - Remove non-UEFI boot commands.
  - Use Distro boot.
  - Remove NOR-connected SPI node by path instead of alias.
  - Rename configs/SynQuacer_defconfig to
    configs/synquacer_developerbox_defconfig.
  - Rename include/configs/SynQuacer.h to include/configs/synquacer.h.
  - Move README under doc/board/socionext/ and make it .rst text.
---
 arch/arm/Kconfig                            |   14 +++
 board/socionext/developerbox/Kconfig        |   36 +++++++
 board/socionext/developerbox/MAINTAINERS    |   14 +++
 board/socionext/developerbox/Makefile       |    9 ++
 board/socionext/developerbox/developerbox.c |  146 +++++++++++++++++++++++++++
 configs/synquacer_developerbox_defconfig    |  114 +++++++++++++++++++++
 doc/board/index.rst                         |    1 
 doc/board/socionext/developerbox.rst        |   87 ++++++++++++++++
 doc/board/socionext/index.rst               |    9 ++
 include/configs/synquacer.h                 |  109 ++++++++++++++++++++
 10 files changed, 539 insertions(+)
 create mode 100644 board/socionext/developerbox/Kconfig
 create mode 100644 board/socionext/developerbox/MAINTAINERS
 create mode 100644 board/socionext/developerbox/Makefile
 create mode 100644 board/socionext/developerbox/developerbox.c
 create mode 100644 configs/synquacer_developerbox_defconfig
 create mode 100644 doc/board/socionext/developerbox.rst
 create mode 100644 doc/board/socionext/index.rst
 create mode 100644 include/configs/synquacer.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 023824df77..7ff24535cd 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1760,6 +1760,19 @@ config ARCH_UNIPHIER
 	  Support for UniPhier SoC family developed by Socionext Inc.
 	  (formerly, System LSI Business Division of Panasonic Corporation)
 
+config ARCH_SYNQUACER
+	bool "Socionext SynQuacer SoCs"
+	select ARM64
+	select DM
+	select GIC_V3
+	select PSCI_RESET
+	select SYSRESET
+	select SYSRESET_PSCI
+	select OF_CONTROL
+	help
+	  Support for SynQuacer SoC family developed by Socionext Inc.
+	  This SoC is used on 96boards EE DeveloperBox.
+
 config ARCH_STM32
 	bool "Support STMicroelectronics STM32 MCU with cortex M"
 	select CPU_V7M
@@ -2102,6 +2115,7 @@ source "board/hisilicon/poplar/Kconfig"
 source "board/isee/igep003x/Kconfig"
 source "board/kontron/sl28/Kconfig"
 source "board/myir/mys_6ulx/Kconfig"
+source "board/socionext/developerbox/Kconfig"
 source "board/spear/spear300/Kconfig"
 source "board/spear/spear310/Kconfig"
 source "board/spear/spear320/Kconfig"
diff --git a/board/socionext/developerbox/Kconfig b/board/socionext/developerbox/Kconfig
new file mode 100644
index 0000000000..706b8dc0f1
--- /dev/null
+++ b/board/socionext/developerbox/Kconfig
@@ -0,0 +1,36 @@
+if ARCH_SYNQUACER
+
+choice
+	prompt "SC2A11 Cortex-A53 MPCore 24cores"
+	optional
+
+config TARGET_DEVELOPERBOX
+	bool "Socionext DeveloperBox"
+	select PCI
+	select DM_PCI
+	select PCIE_ECAM_SYNQUACER
+	select SYS_DISABLE_DCACHE_OPS
+	select OF_BOARD_SETUP
+	help
+	 Choose this option if you build the U-Boot for the DeveloperBox
+	 96boards Enterprise Edition.
+	 This board will booted from SCP firmware and it enables SMMU, thus
+	 the dcache is updated automatically when DMA operation is executed.
+endchoice
+
+config SYS_SOC
+	default "sc2a11"
+
+if TARGET_DEVELOPERBOX
+
+config SYS_BOARD
+	default "developerbox"
+
+config SYS_VENDOR
+	default "socionext"
+
+config SYS_CONFIG_NAME
+	default "synquacer"
+
+endif
+endif
diff --git a/board/socionext/developerbox/MAINTAINERS b/board/socionext/developerbox/MAINTAINERS
new file mode 100644
index 0000000000..aa672b6e05
--- /dev/null
+++ b/board/socionext/developerbox/MAINTAINERS
@@ -0,0 +1,14 @@
+DEVELOPER BOX
+M:	Masami Hiramatsu <masami.hiramatsu at linaro.org>
+M:	Jassi Brar <jaswinder.singh at linaro.org>
+S:	Maintained
+F:	arch/arm/dts/synquacer-*
+F:	board/socionext/developerbox/*
+F:	configs/synquacer_developerbox_defconfig
+F:	drivers/i2c/synquacer_i2c.c
+F:	drivers/mmc/f_sdh30.c
+F:	drivers/net/sni_netsec.c
+F:	drivers/pci/pcie_ecam_synquacer.c
+F:	drivers/spi/spi-synquacer.c
+F:	include/configs/synquacer.h
+F:	doc/board/socionext/developerbox.rst
diff --git a/board/socionext/developerbox/Makefile b/board/socionext/developerbox/Makefile
new file mode 100644
index 0000000000..4a46de995a
--- /dev/null
+++ b/board/socionext/developerbox/Makefile
@@ -0,0 +1,9 @@
+#
+# Author: Masami Hiramatsu <masami.hiramatsu at linaro.org>
+#
+# Copyright (C) 2021 Linaro Ltd.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= developerbox.o
diff --git a/board/socionext/developerbox/developerbox.c b/board/socionext/developerbox/developerbox.c
new file mode 100644
index 0000000000..34335baec3
--- /dev/null
+++ b/board/socionext/developerbox/developerbox.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * u-boot/board/socionext/developerbox/developerbox.c
+ *
+ * Copyright (C) 2016-2017 Socionext Inc.
+ * Copyright (C) 2021 Linaro Ltd.
+ */
+#include <asm/types.h>
+#include <asm/armv8/mmu.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <common.h>
+#include <env_internal.h>
+#include <fdt_support.h>
+#include <log.h>
+
+static struct mm_region sc2a11_mem_map[] = {
+	{
+		.virt = 0x0UL,
+		.phys = 0x0UL,
+		.size = 0x80000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+			 PTE_BLOCK_OUTER_SHARE
+	}, {
+		/* 1st DDR block */
+		.virt = 0x80000000UL,
+		.phys = 0x80000000UL,
+		.size = PHYS_SDRAM_SIZE,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+			 PTE_BLOCK_OUTER_SHARE
+	}, {
+		/* 2nd DDR place holder */
+		0,
+	}, {
+		/* 3rd DDR place holder */
+		0,
+	}, {
+		/* List terminator */
+		0,
+	}
+};
+
+struct mm_region *mem_map = sc2a11_mem_map;
+
+#define DDR_REGION_INDEX(i)	(1 + (i))
+#define MAX_DDR_REGIONS		3
+
+struct draminfo_entry {
+	u64	base;
+	u64	size;
+};
+
+struct draminfo {
+	u32	nr_regions;
+	u32	reserved;
+	struct draminfo_entry	entry[3];
+};
+
+struct draminfo *synquacer_draminfo = (void *)SQ_DRAMINFO_BASE;
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define LOAD_OFFSET 0x100
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+int board_init(void)
+{
+	gd->bd->bi_boot_params = CONFIG_SYS_LOAD_ADDR + LOAD_OFFSET;
+
+	gd->env_addr = (ulong)&default_environment[0];
+
+	return 0;
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	/* Remove SPI NOR and I2C0 for making DT compatible with EDK2 */
+	fdt_del_node_and_alias(blob, "spi_nor");
+	fdt_del_node_and_alias(blob, "i2c0");
+
+	return 0;
+}
+
+/*
+ * DRAM configuration
+ */
+
+int dram_init(void)
+{
+	struct draminfo_entry *ent = synquacer_draminfo->entry;
+	struct mm_region *mr;
+	int i, ri;
+
+	if (synquacer_draminfo->nr_regions < 1) {
+		log_err("Failed to get correct DRAM information\n");
+		return -1;
+	}
+
+	/*
+	 * U-Boot RAM size must be under the first DRAM region so that it doesn't
+	 * access secure memory which is at the end of the first DRAM region.
+	 */
+	gd->ram_size = ent[0].size;
+
+	/* Update memory region maps */
+	for (i = 0; i < synquacer_draminfo->nr_regions; i++) {
+		if (i >= MAX_DDR_REGIONS)
+			break;
+
+		ri = DDR_REGION_INDEX(i);
+		mem_map[ri].phys = ent[i].base;
+		mem_map[ri].size = ent[i].size;
+		if (i == 0)
+			continue;
+
+		mr = &mem_map[DDR_REGION_INDEX(0)];
+		mem_map[ri].virt = mr->virt + mr->size;
+		mem_map[ri].attrs = mr->attrs;
+	}
+
+	return 0;
+}
+
+int dram_init_banksize(void)
+{
+	struct draminfo_entry *ent = synquacer_draminfo->entry;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(gd->bd->bi_dram); i++) {
+		if (i < synquacer_draminfo->nr_regions) {
+			debug("%s: dram[%d] = %llx@%llx\n", __func__, i, ent[i].size, ent[i].base);
+			gd->bd->bi_dram[i].start = ent[i].base;
+			gd->bd->bi_dram[i].size = ent[i].size;
+		}
+	}
+
+	return 0;
+}
+
+int print_cpuinfo(void)
+{
+	printf("CPU:   SC2A11:Cortex-A53 MPCore 24cores\n");
+	return 0;
+}
diff --git a/configs/synquacer_developerbox_defconfig b/configs/synquacer_developerbox_defconfig
new file mode 100644
index 0000000000..2875fcd794
--- /dev/null
+++ b/configs/synquacer_developerbox_defconfig
@@ -0,0 +1,114 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SYNQUACER=y
+CONFIG_SYS_TEXT_BASE=0x08200000
+CONFIG_ENV_SIZE=0x30000
+CONFIG_ENV_OFFSET=0x300000
+CONFIG_DEBUG_UART_BASE=0x2a400000
+CONFIG_DEBUG_UART_CLOCK=62500000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_TARGET_DEVELOPERBOX=y
+CONFIG_DEFAULT_DEVICE_TREE="synquacer-sc2a11-developerbox"
+CONFIG_AHCI=y
+CONFIG_BOOTSTAGE_STASH_SIZE=4096
+CONFIG_BOOTM_EFI=y
+CONFIG_LOGLEVEL=9
+CONFIG_LOG_MAX_LEVEL=7
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTEFI=y
+CONFIG_CMD_NVEDIT_EFI=y
+CONFIG_CMD_EFIDEBUG=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_IMLS=y
+CONFIG_CMD_NVEDIT_INFO=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_NET=y
+CONFIG_CMD_BOOTP=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_DATE=y
+CONFIG_CMD_RTC=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_POWEROFF=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_SATA=y
+CONFIG_CMD_NVME=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDPARTS_DEFAULT="nor1:448k(BootStrap-BL1),576k(Flash-Writer),512k(SCP-BL2),480k(FIP-TFA),32k(Stg2-Tables),1m at 2m(U-Boot),1m at 3m(UBoot-Env),2m at 5m(Ex-OPTEE)"
+CONFIG_MTDIDS_DEFAULT="nor1=nor1"
+CONFIG_CMD_LOG=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_EFI_PARTITION=y
+CONFIG_EFI_LOADER=y
+CONFIG_EFI_DEVICE_PATH_TO_TEXT=y
+CONFIG_EFI_UNICODE_COLLATION_PROTOCOL2=y
+CONFIG_EFI_UNICODE_CAPITALIZATION=y
+CONFIG_EFI_HAVE_RUNTIME_RESET=y
+CONFIG_EFI_GET_TIME=y
+CONFIG_EFI_SET_TIME=y
+CONFIG_CMD_EFI_VARIABLE_FILE_STORE=Y
+CONFIG_OF_SEPARATE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_PROT_UDP=y
+CONFIG_BAUDRATE=115200
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_CONS_INDEX=0
+CONFIG_DM_SERIAL=y
+CONFIG_PL01X_SERIAL=y
+CONFIG_SATA=y
+CONFIG_NVME=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_SYNQUACER=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_F_SDH30=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_SPEED=31250000
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHYLIB=y
+CONFIG_PHYLIB_10G=y
+CONFIG_NET=y
+CONFIG_NETDEVICES=y
+CONFIG_SNI_NETSEC=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_PHY_GIGE=y
+CONFIG_RGMII=y
+CONFIG_MII=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_PCF8563=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_SYNQUACER_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_PCI=y
+CONFIG_USB_STORAGE=y
diff --git a/doc/board/index.rst b/doc/board/index.rst
index a70d2de19d..242372b321 100644
--- a/doc/board/index.rst
+++ b/doc/board/index.rst
@@ -21,6 +21,7 @@ Board-specific doc
    rockchip/index
    sifive/index
    sipeed/index
+   socionext/index
    st/index
    tbs/index
    toradex/index
diff --git a/doc/board/socionext/developerbox.rst b/doc/board/socionext/developerbox.rst
new file mode 100644
index 0000000000..2d943c23be
--- /dev/null
+++ b/doc/board/socionext/developerbox.rst
@@ -0,0 +1,87 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Introduction
+============
+
+DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
+
+* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
+* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
+* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
+  (1x slots are connected via PCIe bridge chip)
+* 4 USB-3.0 ports
+* 2 SATA ports
+* 1 GbE network port
+* 1 USB-UART serial port (micro USB)
+* 64MB SPI NOR Flash
+* 8GB eMMC Flash Storage
+* 96boards LS connector
+
+The DeveloperBox schematic can be found here: -
+https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdf
+
+And the other documents can be found here: -
+https://www.96boards.org/documentation/enterprise/developerbox/
+
+
+Currently, the U-Boot port supports: -
+
+* USB
+* eMMC
+* SPI-NOR
+* SATA
+* GbE
+
+The DeveloperBox boots the TF-A and EDK2 as a main bootloader by default.
+The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as
+BL33, but no need to combine with it.
+
+Compile from source
+===================
+
+You can build U-Boot without any additinal source code.::
+
+  cd u-boot
+  export ARCH=arm64
+  export CROSS_COMPILE=aarch64-linux-gnu-
+  make SynQuacer_defconfig
+  make -j `noproc`
+
+Then, expand the binary to 1MB for preparing flash.::
+
+  cp u-boot.bin SPI_NOR_UBOOT.fd
+  truncate -s 1M SPI_NOR_UBOOT.fd
+
+Installation
+============
+
+You can install the SNI_NOR_UBOOT.fd via NOR flash writer.
+
+Flashing the U-Boot image on DeveloperBox requires a 96boards UART mezzanine or other mezzanine which can connect to LS-UART0 port.
+Connect USB cable from host to the LS-UART0 and set DSW2-7 to ON, and turn the board on again. The flash writer program will be started automatically; don’t forget to turn the DSW2-7 off again after flashing.
+
+*!!CAUTION!! If you failed to write the U-Boot image on wrong address, the board can be bricked. See below page if you need to recover the bricked board. See the following page for more detail*
+
+https://www.96boards.org/documentation/enterprise/developerbox/installation/board-recovery.md.html
+
+When the serial flasher is running correctly is will show the following boot messages shown via LS-UART0::
+
+
+  /*------------------------------------------*/
+  /*  SC2A11 "SynQuacer" series Flash writer  */
+  /*                                          */
+  /*  Version: cd254ac                        */
+  /*  Build: 12/15/17 11:25:45                */
+  /*------------------------------------------*/
+
+  Command Input >
+
+Once the flasher tool is running we are ready flash the UEFI image::
+
+  flash rawwrite 200000 100000
+  >> Send SPI_NOR_UBOOT.fd via XMODEM (Control-A S in minicom) <<
+
+*!!NOTE!! The flasher command parameter is different from the command for board recovery. U-Boot uses the offset 200000 (2-five-0, 2M in hex) and the size 100000 (1-five-0, 1M in hex).*
+
+After transferring the SPI_NOR_UBOOT.fd, turn off the DSW2-7 and reset the board.
+
diff --git a/doc/board/socionext/index.rst b/doc/board/socionext/index.rst
new file mode 100644
index 0000000000..4673dcc45b
--- /dev/null
+++ b/doc/board/socionext/index.rst
@@ -0,0 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Socionext
+=========
+
+.. toctree::
+   :maxdepth: 2
+
+   developerbox
diff --git a/include/configs/synquacer.h b/include/configs/synquacer.h
new file mode 100644
index 0000000000..0dab4de1f1
--- /dev/null
+++ b/include/configs/synquacer.h
@@ -0,0 +1,109 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2016-2017 Socionext Inc.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* Timers for fasp(TIMCLK) */
+#define CONFIG_SYS_HZ			1000		/* 1 msec */
+#define CONFIG_SYS_TIMERBASE		0x31080000	/* AP Timer 1 (ARM-SP804) */
+
+/*
+ * SDRAM (for initialize)
+ */
+#define CONFIG_SYS_SDRAM_BASE		(0x80000000)	/* Start address of DDR3 */
+#define PHYS_SDRAM_SIZE			(0x7c000000)	/* Default size (2GB - Secure memory) */
+
+#define CONFIG_VERY_BIG_RAM				/* SynQuacer supports up to 64GB */
+#define CONFIG_MAX_MEM_MAPPED		PHYS_SDRAM_SIZE
+
+#define SQ_DRAMINFO_BASE		(0x2e00ffc0)	/* DRAM info from TF-A */
+
+/*
+ * Boot info
+ */
+#define CONFIG_SYS_INIT_SP_ADDR		(0xe0000000)	/* stack of init proccess */
+#define CONFIG_SYS_MALLOC_LEN		(0x01000000)	/* 16Mbyte size of malloc() */
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE /* default kernel load address */
+
+/*
+ * Hardware drivers support
+ */
+
+/* RTC */
+#define CONFIG_SYS_I2C_RTC_ADDR		0x51
+
+/* Serial (pl011)       */
+#define UART_CLK			(62500000)
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_PL011_SERIAL
+#define CONFIG_PL011_CLOCK		UART_CLK
+#define CONFIG_PL01x_PORTS		{(void *)(0x2a400000)}
+
+#define CONFIG_ENV_OVERWRITE		/* ethaddr can be reprogrammed */
+
+/* Support MTD */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_FLASH_BASE		(0x08000000)
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE}
+
+#define CONFIG_SYS_MEMTEST_START	(CONFIG_SYS_SDRAM_BASE + (512 * 1024))
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + PHYS_SDRAM_SIZE)
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200, 19200, 38400, 57600, 9600 }
+
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_MAXARGS		128
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Since U-Boot 64bit PCIe support is limited, disable 64bit MMIO support */
+/* #define CONFIG_SYS_PCI_64BIT		1 */
+
+/* Distro boot settings */
+#ifndef CONFIG_SPL_BUILD
+#ifdef CONFIG_CMD_USB
+#define BOOT_TARGET_DEVICE_USB(func)	func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICE_USB(func)
+#endif
+
+#ifdef CONFIG_CMD_MMC
+#define BOOT_TARGET_DEVICE_MMC(func)	func(MMC, mmc, 0)
+#else
+#define BOOT_TARGET_DEVICE_MMC(func)
+#endif
+
+#ifdef CONFIG_CMD_NVME
+#define BOOT_TARGET_DEVICE_NVME(func)	func(NVME, nvme, 0)
+#else
+#define BOOT_TARGET_DEVICE_NVME(func)
+#endif
+
+#ifdef CONFIG_CMD_SCSI
+#define BOOT_TARGET_DEVICE_SCSI(func)	func(SCSI, scsi, 0) func(SCSI, scsi, 1)
+#else
+#define BOOT_TARGET_DEVICE_SCSI(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func)	\
+	BOOT_TARGET_DEVICE_USB(func)	\
+	BOOT_TARGET_DEVICE_MMC(func)	\
+	BOOT_TARGET_DEVICE_SCSI(func)	\
+	BOOT_TARGET_DEVICE_NVME(func)	\
+
+#include <config_distro_bootcmd.h>
+#else /* CONFIG_SPL_BUILD */
+#define BOOTENV
+#endif
+
+#define	CONFIG_EXTRA_ENV_SETTINGS		\
+	"fdt_addr_r=0x9fe00000\0"		\
+	"kernel_addr_r=0x90000000\0"		\
+	"ramdisk_addr_r=0xa0000000\0"		\
+	"scriptaddr=0x88000000\0"		\
+	"pxefile_addr_r=0x88100000\0"		\
+	BOOTENV
+
+#endif /* __CONFIG_H */



More information about the U-Boot mailing list