[PATCH] imx: ventana: enable dm support for PCI and FEC ethernet
Tim Harvey
tharvey at gateworks.com
Sat May 29 03:22:23 CEST 2021
On Mon, May 3, 2021 at 11:21 AM Tim Harvey <tharvey at gateworks.com> wrote:
>
> Enable driver model support for FEC ethernet which allows us to remove
> the iomux and board_eth_init function. Replace the toggling of the ethernet
> phy reset with dt configuration.
>
> Enable driver model support for PCI which allows us to remove the
> eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
> PCI devices on init such as the e1000 that is present on the GW552x.
>
> Convert board_pci_fixup to use dm callback and remove pcidisable env
> variable which is not supported for DM_PCI and thus leave PCI always
> enabled during init.
>
> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
> ---
> v2: rebase
> ---
> arch/arm/dts/imx6qdl-gw51xx.dtsi | 2 +
> arch/arm/dts/imx6qdl-gw52xx.dtsi | 2 +
> arch/arm/dts/imx6qdl-gw53xx.dtsi | 3 +
> arch/arm/dts/imx6qdl-gw54xx.dtsi | 3 +
> arch/arm/dts/imx6qdl-gw560x.dtsi | 2 +
> arch/arm/dts/imx6qdl-gw5903.dtsi | 3 +
> arch/arm/dts/imx6qdl-gw5904.dtsi | 3 +
> arch/arm/dts/imx6qdl-gw5907.dtsi | 2 +
> arch/arm/dts/imx6qdl-gw5910.dtsi | 3 +
> arch/arm/dts/imx6qdl-gw5912.dtsi | 4 +
> arch/arm/dts/imx6qdl-gw5913.dtsi | 3 +
> board/gateworks/gw_ventana/common.h | 1 -
> board/gateworks/gw_ventana/gw_ventana.c | 99 ++++---------------------
> configs/gwventana_emmc_defconfig | 5 ++
> configs/gwventana_gw5904_defconfig | 5 ++
> configs/gwventana_nand_defconfig | 5 ++
> include/configs/gw_ventana.h | 10 ---
> 17 files changed, 61 insertions(+), 94 deletions(-)
>
> diff --git a/arch/arm/dts/imx6qdl-gw51xx.dtsi b/arch/arm/dts/imx6qdl-gw51xx.dtsi
> index 2a21c6731e..7e28463084 100644
> --- a/arch/arm/dts/imx6qdl-gw51xx.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw51xx.dtsi
> @@ -129,6 +129,8 @@
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw52xx.dtsi b/arch/arm/dts/imx6qdl-gw52xx.dtsi
> index 6eedf8d40d..f1d9ba1fac 100644
> --- a/arch/arm/dts/imx6qdl-gw52xx.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw52xx.dtsi
> @@ -195,6 +195,8 @@
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw53xx.dtsi b/arch/arm/dts/imx6qdl-gw53xx.dtsi
> index 9deec7e352..172a45ba17 100644
> --- a/arch/arm/dts/imx6qdl-gw53xx.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw53xx.dtsi
> @@ -188,6 +188,8 @@
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> @@ -597,6 +599,7 @@
> MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
> >;
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw54xx.dtsi b/arch/arm/dts/imx6qdl-gw54xx.dtsi
> index a30ba4848e..e09fad6068 100644
> --- a/arch/arm/dts/imx6qdl-gw54xx.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw54xx.dtsi
> @@ -225,6 +225,8 @@
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> @@ -675,6 +677,7 @@
> MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
> >;
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw560x.dtsi b/arch/arm/dts/imx6qdl-gw560x.dtsi
> index 0786b0d546..bfe65fd3c0 100644
> --- a/arch/arm/dts/imx6qdl-gw560x.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw560x.dtsi
> @@ -279,6 +279,8 @@
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw5903.dtsi b/arch/arm/dts/imx6qdl-gw5903.dtsi
> index 78f9ec90b7..6ebf6aef2f 100644
> --- a/arch/arm/dts/imx6qdl-gw5903.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw5903.dtsi
> @@ -223,6 +223,9 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw5904.dtsi b/arch/arm/dts/imx6qdl-gw5904.dtsi
> index 5b7bd56932..9adbd728dc 100644
> --- a/arch/arm/dts/imx6qdl-gw5904.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw5904.dtsi
> @@ -200,6 +200,9 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
>
> fixed-link {
> diff --git a/arch/arm/dts/imx6qdl-gw5907.dtsi b/arch/arm/dts/imx6qdl-gw5907.dtsi
> index c8b29246b7..58f73a141e 100644
> --- a/arch/arm/dts/imx6qdl-gw5907.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw5907.dtsi
> @@ -131,6 +131,8 @@
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw5910.dtsi b/arch/arm/dts/imx6qdl-gw5910.dtsi
> index 248e077a56..446c1043a7 100644
> --- a/arch/arm/dts/imx6qdl-gw5910.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw5910.dtsi
> @@ -146,6 +146,9 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw5912.dtsi b/arch/arm/dts/imx6qdl-gw5912.dtsi
> index 7593872c07..88234a6f13 100644
> --- a/arch/arm/dts/imx6qdl-gw5912.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw5912.dtsi
> @@ -141,6 +141,9 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> @@ -426,6 +429,7 @@
> MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
> >;
> };
>
> diff --git a/arch/arm/dts/imx6qdl-gw5913.dtsi b/arch/arm/dts/imx6qdl-gw5913.dtsi
> index 9fae4cccd7..f4c2b2189f 100644
> --- a/arch/arm/dts/imx6qdl-gw5913.dtsi
> +++ b/arch/arm/dts/imx6qdl-gw5913.dtsi
> @@ -121,6 +121,9 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <10>;
> + phy-reset-post-delay = <100>;
> status = "okay";
> };
>
> diff --git a/board/gateworks/gw_ventana/common.h b/board/gateworks/gw_ventana/common.h
> index d73850c5b9..813f7d9f56 100644
> --- a/board/gateworks/gw_ventana/common.h
> +++ b/board/gateworks/gw_ventana/common.h
> @@ -11,7 +11,6 @@
> #include "ventana_eeprom.h"
>
> /* GPIO's common to all baseboards */
> -#define GP_PHY_RST IMX_GPIO_NR(1, 30)
> #define GP_RS232_EN IMX_GPIO_NR(2, 11)
> #define GP_MSATA_SEL IMX_GPIO_NR(2, 8)
>
> diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
> index 5237f2dac4..1ed9c1a39f 100644
> --- a/board/gateworks/gw_ventana/gw_ventana.c
> +++ b/board/gateworks/gw_ventana/gw_ventana.c
> @@ -31,7 +31,6 @@
> #include <linux/ctype.h>
> #include <miiphy.h>
> #include <mtd_node.h>
> -#include <netdev.h>
> #include <pci.h>
> #include <linux/delay.h>
> #include <linux/libfdt.h>
> @@ -54,42 +53,6 @@ DECLARE_GLOBAL_DATA_PTR;
> struct ventana_board_info ventana_info;
> static int board_type;
>
> -/* ENET */
> -static iomux_v3_cfg_t const enet_pads[] = {
> - IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
> - MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |
> - MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
> - MUX_PAD_CTRL(ENET_PAD_CTRL)),
> - /* PHY nRST */
> - IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | DIO_PAD_CFG),
> -};
> -
> -static void setup_iomux_enet(int gpio)
> -{
> - SETUP_IOMUX_PADS(enet_pads);
> -
> - /* toggle PHY_RST# */
> - gpio_request(gpio, "phy_rst#");
> - gpio_direction_output(gpio, 0);
> - mdelay(10);
> - gpio_set_value(gpio, 1);
> - mdelay(100);
> -}
> -
> #ifdef CONFIG_USB_EHCI_MX6
> /* toggle USB_HUB_RST# for boards that have it; it is not defined in dt */
> int board_ehci_hcd_init(int port)
> @@ -195,40 +158,7 @@ int mv88e61xx_hw_reset(struct phy_device *phydev)
> }
> #endif // CONFIG_MV88E61XX_SWITCH
>
> -int board_eth_init(struct bd_info *bis)
> -{
> -#ifdef CONFIG_FEC_MXC
> - struct ventana_board_info *info = &ventana_info;
> -
> - if (test_bit(EECONFIG_ETH0, info->config)) {
> - setup_iomux_enet(GP_PHY_RST);
> - cpu_eth_init(bis);
> - }
> -#endif
> -
> -#ifdef CONFIG_E1000
> - e1000_initialize(bis);
> -#endif
> -
> -#ifdef CONFIG_CI_UDC
> - /* For otg ethernet*/
> - usb_eth_initialize(bis);
> -#endif
> -
> - /* default to the first detected enet dev */
> - if (!env_get("ethprime")) {
> - struct eth_device *dev = eth_get_dev_by_index(0);
> - if (dev) {
> - env_set("ethprime", dev->name);
> - printf("set ethprime to %s\n", env_get("ethprime"));
> - }
> - }
> -
> - return 0;
> -}
> -
> #if defined(CONFIG_VIDEO_IPUV3)
> -
> static void enable_hdmi(struct display_info_t const *dev)
> {
> imx_enable_hdmi_phy();
> @@ -427,7 +357,6 @@ int power_init_board(void)
> return 0;
> }
>
> -#if defined(CONFIG_CMD_PCI)
> int imx6_pcie_toggle_reset(void)
> {
> if (board_type < GW_UNKNOWN) {
> @@ -448,6 +377,7 @@ int imx6_pcie_toggle_reset(void)
> #define MAX_PCI_DEVS 32
> struct pci_dev {
> pci_dev_t devfn;
> + struct udevice *dev;
> unsigned short vendor;
> unsigned short device;
> unsigned short class;
> @@ -458,18 +388,21 @@ struct pci_dev pci_devs[MAX_PCI_DEVS];
> int pci_devno;
> int pci_bridgeno;
>
> -void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
> - unsigned short vendor, unsigned short device,
> - unsigned short class)
> +void board_pci_fixup_dev(struct udevice *bus, struct udevice *udev)
> {
> - int i;
> - u32 dw;
> + struct pci_child_plat *pdata = dev_get_parent_plat(udev);
> struct pci_dev *pdev = &pci_devs[pci_devno++];
> + unsigned short vendor = pdata->vendor;
> + unsigned short device = pdata->device;
> + unsigned int class = pdata->class;
> + pci_dev_t dev = dm_pci_get_bdf(udev);
> + int i;
>
> debug("%s: %02d:%02d.%02d: %04x:%04x\n", __func__,
> PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), vendor, device);
>
> /* store array of devs for later use in device-tree fixup */
> + pdev->dev = udev;
> pdev->devfn = dev;
> pdev->vendor = vendor;
> pdev->device = device;
> @@ -496,19 +429,19 @@ void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
> if (vendor == PCI_VENDOR_ID_PLX &&
> (device & 0xfff0) == 0x8600 &&
> PCI_DEV(dev) == 0 && PCI_FUNC(dev) == 0) {
> + ulong val;
> debug("configuring PLX 860X downstream PERST#\n");
> - pci_hose_read_config_dword(hose, dev, 0x62c, &dw);
> - dw |= 0xaaa8; /* GPIO1-7 outputs */
> - pci_hose_write_config_dword(hose, dev, 0x62c, dw);
> + pci_bus_read_config(bus, dev, 0x62c, &val, PCI_SIZE_32);
> + val |= 0xaaa8; /* GPIO1-7 outputs */
> + pci_bus_write_config(bus, dev, 0x62c, val, PCI_SIZE_32);
>
> - pci_hose_read_config_dword(hose, dev, 0x644, &dw);
> - dw |= 0xfe; /* GPIO1-7 output high */
> - pci_hose_write_config_dword(hose, dev, 0x644, dw);
> + pci_bus_read_config(bus, dev, 0x644, &val, PCI_SIZE_32);
> + val |= 0xfe; /* GPIO1-7 output high */
> + pci_bus_write_config(bus, dev, 0x644, val, PCI_SIZE_32);
>
> mdelay(100);
> }
> }
> -#endif /* CONFIG_CMD_PCI */
>
> #ifdef CONFIG_SERIAL_TAG
> /*
> diff --git a/configs/gwventana_emmc_defconfig b/configs/gwventana_emmc_defconfig
> index d5270c5232..c2d4ad3b5d 100644
> --- a/configs/gwventana_emmc_defconfig
> +++ b/configs/gwventana_emmc_defconfig
> @@ -34,6 +34,7 @@ CONFIG_USE_PREBOOT=y
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_MISC_INIT_R=y
> +CONFIG_PCI_INIT_R=y
> CONFIG_SPL_BOARD_INIT=y
> CONFIG_SPL_STACK_R=y
> CONFIG_SPL_FIT_IMAGE_TINY=y
> @@ -86,9 +87,13 @@ CONFIG_SUPPORT_EMMC_BOOT=y
> CONFIG_FSL_USDHC=y
> CONFIG_MTD=y
> CONFIG_PHYLIB=y
> +CONFIG_DM_ETH=y
> +CONFIG_DM_MDIO=y
> CONFIG_E1000=y
> +CONFIG_FEC_MXC=y
> CONFIG_MII=y
> CONFIG_PCI=y
> +CONFIG_DM_PCI=y
> CONFIG_PINCTRL=y
> CONFIG_PINCTRL_IMX6=y
> CONFIG_DM_REGULATOR=y
> diff --git a/configs/gwventana_gw5904_defconfig b/configs/gwventana_gw5904_defconfig
> index 091bf30c3b..3d349818cd 100644
> --- a/configs/gwventana_gw5904_defconfig
> +++ b/configs/gwventana_gw5904_defconfig
> @@ -34,6 +34,7 @@ CONFIG_USE_PREBOOT=y
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_MISC_INIT_R=y
> +CONFIG_PCI_INIT_R=y
> CONFIG_SPL_BOARD_INIT=y
> CONFIG_SPL_STACK_R=y
> CONFIG_SPL_FIT_IMAGE_TINY=y
> @@ -90,9 +91,13 @@ CONFIG_MV88E61XX_SWITCH=y
> CONFIG_MV88E61XX_CPU_PORT=5
> CONFIG_MV88E61XX_PHY_PORTS=0xf
> CONFIG_MV88E61XX_FIXED_PORTS=0x0
> +CONFIG_DM_ETH=y
> +CONFIG_DM_MDIO=y
> CONFIG_E1000=y
> +CONFIG_FEC_MXC=y
> CONFIG_MII=y
> CONFIG_PCI=y
> +CONFIG_DM_PCI=y
> CONFIG_PINCTRL=y
> CONFIG_PINCTRL_IMX6=y
> CONFIG_DM_REGULATOR=y
> diff --git a/configs/gwventana_nand_defconfig b/configs/gwventana_nand_defconfig
> index 0ccd3e9dfd..2bb9a21585 100644
> --- a/configs/gwventana_nand_defconfig
> +++ b/configs/gwventana_nand_defconfig
> @@ -34,6 +34,7 @@ CONFIG_USE_PREBOOT=y
> CONFIG_DISPLAY_BOARDINFO_LATE=y
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_MISC_INIT_R=y
> +CONFIG_PCI_INIT_R=y
> CONFIG_SPL_BOARD_INIT=y
> CONFIG_SPL_STACK_R=y
> CONFIG_SPL_FIT_IMAGE_TINY=y
> @@ -92,9 +93,13 @@ CONFIG_MTD_RAW_NAND=y
> CONFIG_NAND_MXS=y
> CONFIG_NAND_MXS_DT=y
> CONFIG_PHYLIB=y
> +CONFIG_DM_ETH=y
> +CONFIG_DM_MDIO=y
> CONFIG_E1000=y
> +CONFIG_FEC_MXC=y
> CONFIG_MII=y
> CONFIG_PCI=y
> +CONFIG_DM_PCI=y
> CONFIG_PINCTRL=y
> CONFIG_PINCTRL_IMX6=y
> CONFIG_DM_REGULATOR=y
> diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
> index 5754b6aef0..4f2f323b77 100644
> --- a/include/configs/gw_ventana.h
> +++ b/include/configs/gw_ventana.h
> @@ -65,8 +65,6 @@
> * PCI express
> */
> #ifdef CONFIG_CMD_PCI
> -#define CONFIG_PCI_SCAN_SHOW
> -#define CONFIG_PCI_FIXUP_DEV
> #define CONFIG_PCIE_IMX
> #endif
>
> @@ -82,13 +80,6 @@
>
> /* Various command support */
>
> -/* Ethernet support */
> -#define CONFIG_FEC_MXC
> -#define IMX_FEC_BASE ENET_BASE_ADDR
> -#define CONFIG_FEC_XCV_TYPE RGMII
> -#define CONFIG_FEC_MXC_PHYADDR 0
> -#define CONFIG_ARP_TIMEOUT 200UL
> -
> /* USB Configs */
> #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
> #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
> @@ -129,7 +120,6 @@
> #define CONFIG_SERVERIP 192.168.1.146
>
> #define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
> - "pcidisable=1\0" \
> "splashpos=m,m\0" \
> "usb_pgood_delay=2000\0" \
> "console=ttymxc1\0" \
> --
> 2.17.1
>
Stefano,
Is everything good with this? I don't see that you've picked it up
yet. I'm anxious to get off the naughty list regarding moving to DM :)
Thanks,
Tim
More information about the U-Boot
mailing list