[PATCH 2/2] ARM: dts: at91: sama7g5ek: Add QSPI0 node

[Tudor Ambarus]

QSPI0 has a MX66LM1G45G SPI NOR flash connected.
Enable the controller and describe the flash.

Signed-off-by: Tudor Ambarus <tudor.ambarus at microchip.com>
---
 arch/arm/dts/sama7g5ek.dts | 38 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm/dts/sama7g5ek.dts b/arch/arm/dts/sama7g5ek.dts
index 1c59a8aaf8..16192ca0b1 100644
--- a/arch/arm/dts/sama7g5ek.dts
+++ b/arch/arm/dts/sama7g5ek.dts
@@ -11,6 +11,7 @@
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include "sama7g5.dtsi"
 #include "sama7g5-pinfunc.h"
+#include <dt-bindings/pinctrl/at91.h>
 
 / {
 	model = "Microchip SAMA7G5 Evaluation Kit";
@@ -64,6 +65,24 @@
 	};
 };
 
+&qspi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <133000000>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		m25p,fast-read;
+
+	};
+};
+
 &flx1 {
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
 	status = "okay";
@@ -126,6 +145,25 @@
 		bias-pull-up;
 	};
 
+	pinctrl_qspi: qspi {
+		pinmux = <PIN_PB12__QSPI0_IO0>,
+			 <PIN_PB11__QSPI0_IO1>,
+			 <PIN_PB10__QSPI0_IO2>,
+			 <PIN_PB9__QSPI0_IO3>,
+			 <PIN_PB16__QSPI0_IO4>,
+			 <PIN_PB17__QSPI0_IO5>,
+			 <PIN_PB18__QSPI0_IO6>,
+			 <PIN_PB19__QSPI0_IO7>,
+			 <PIN_PB13__QSPI0_CS>,
+			 <PIN_PB14__QSPI0_SCK>,
+			 <PIN_PB15__QSPI0_SCKN>,
+			 <PIN_PB20__QSPI0_DQS>,
+			 <PIN_PB21__QSPI0_INT>;
+		bias-disable;
+		slew-rate = <0>;
+		atmel,drive-strength = <ATMEL_PIO_DRVSTR_HI>;
+	};
+
 	pinctrl_sdmmc0_cmd_data_default: sdmmc0_cmd_data_default {
 		pinmux = <PIN_PA1__SDMMC0_CMD>,
 			 <PIN_PA3__SDMMC0_DAT0>,
-- 
2.25.1