[PATCH v4 4/5] sf: doc: Add documentation for the 'sf' command
Heinrich Schuchardt
xypron.glpk at gmx.de
Sat Nov 13 12:34:52 CET 2021
On 9/19/21 23:49, Simon Glass wrote:
> This command is fairly complicated so documentation is useful.
> Unfortunately I an not sure how the MTD side of things works and cannot
> find information about that.
>
> Signed-off-by: Simon Glass <sjg at chromium.org>
>
> Acked-by: Pratyush Yadav <p.yadav at ti.com>
> ---
>
> Changes in v4:
> - Split out the 'const' change into a separate patch
> - Show the 'sf probe' output in the examples
>
> Changes in v2:
> - Many fixes as suggested by Heinrich
>
> doc/usage/index.rst | 1 +
> doc/usage/sf.rst | 245 ++++++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 246 insertions(+)
> create mode 100644 doc/usage/sf.rst
>
> diff --git a/doc/usage/index.rst b/doc/usage/index.rst
> index 356f2a56181..9a7b12b7c54 100644
> --- a/doc/usage/index.rst
> +++ b/doc/usage/index.rst
> @@ -43,6 +43,7 @@ Shell commands
> qfw
> reset
> sbi
> + sf
Please, keep this list in alphabetical order.
> scp03
> setexpr
> size
> diff --git a/doc/usage/sf.rst b/doc/usage/sf.rst
> new file mode 100644
> index 00000000000..71bd1be5175
> --- /dev/null
> +++ b/doc/usage/sf.rst
> @@ -0,0 +1,245 @@
> +.. SPDX-License-Identifier: GPL-2.0+:
> +
> +sf command
> +==========
> +
> +Synopis
> +-------
> +
> +::
> +
> + sf probe [[[<bus>:]<cs>] [<hz> [<mode>]]]
> + sf read <addr> <offset>|<partition> <len>
> + sf write <addr> <offset>|<partition> <len>
> + sf erase <offset>|<partition> <len>
> + sf update <addr> <offset>|<partition> <len>
> + sf protect lock|unlock <sector> <len>
> + sf test <offset>|<partition> <len>
> +
> +Description
> +-----------
> +
> +The *sf* command is used to access SPI flash, supporting read/write/erase and
> +a few other functions.
> +
> +Probe
> +-----
> +
> +The flash must first be probed with *sf probe* before any of the other
> +subcommands can be used. All of the parameters are optional:
> +
> +bus
> + SPI bus number containing the SPI-flash chip, e.g. 0. If you don't know
> + the number, you can use 'dm uclass' to see all the spi devices,
> + and check the value for 'seq' for each one (here 0 and 2)::
I would have expected the 'spi' command to have an info sub-command like
the other subsystems. But that is missing.
> +
> + uclass 89: spi
> + 0 spi at 0 @ 05484960, seq 0
> + 1 spi at 1 @ 05484b40, seq 2
> +
> +cs
> + SPI chip-select to use for the chip. This is often 0 and can be omitted,
> + but in some cases multiple slaves are attached to a SPI controller,
> + selected by a chip-select line for each one.
> +
> +hz
> + Speed of the SPI bus in hertz. This normally defaults to 100000, i.e.
> + 100KHz, which is very slow. Note that if the device exists in the
> + device tree, there might be a speed provided there, in which case this
> + setting is ignored.
> +
> +mode
> + SPI mode to use:
> +
> + ===== ================
> + Mode Meaning
> + ===== ================
> + 0 CPOL=0, CPHA=0
> + 1 CPOL=0, CPHA=1
> + 2 CPOL=1, CPHA=0
> + 3 CPOL=1, CPHA=1
> + ===== ================
> +
> + Clock phase (CPHA) 0 means that data is transferred (sampled) on the
> + first clock edge; 1 means the second.
> +
> + Clock polarity (CPOL) controls the idle state of the clock, 0 for low,
> + 1 for high.
> + The active state is the opposite of idle.
> +
> + You may find this `SPI documentation`_ useful.
> +
> +Parameters for other subcommands (described below) are as follows:
I would not expect parameters for other sub-commands in chapter "Probe".
Please put all parameters into a separate section "Parameters". This
makes navigation easier.
> +
> +addr
> + Memory address to start transfer
> +
> +offset
> + Flash offset to start transfer
> +
> +partition
> + If the parameter is not numeric, it is assumed to be a partition
> + description in the format <dev_type><dev_num>,<part_num> which is not
> + covered here. This requires CONFIG_CMD_MTDPARTS.
> +
> +len
> + Number of bytes to transfer
> +
> +Read
> +~~~~
> +
> +Use *sf read* to read from SPI flash to memory. The read will fail if an
> +attempt is made to read past the end of the flash.
> +
> +
> +Write
> +~~~~~
> +
> +Use *sf write* to write from memory to SPI flash. The SPI flash should be
> +erased first, since otherwise the result is undefined.
> +
> +The write will fail if an attempt is made to read past the end of the flash.
> +
> +
> +Erase
> +~~~~~
> +
> +Use *sf erase* to erase a region of SPI flash. The erase will fail if any part
> +of the region to be erased is protected or lies past the end of the flash. It
> +may also fail if the start offset or length are not aligned to an erase region
> +(e.g. 256 bytes).
> +
> +
> +Update
> +~~~~~~
> +
> +Use *sf update* to automatically erase and update a region of SPI flash from
> +memory. This works a sector at a time (typical 4KB or 64KB). For each
> +sector it first checks if the sector already has the right data. If so it is
> +skipped. If not, the sector is erased and the new data written. Note that if
> +the length is not a multiple of the erase size, the space after the data in
> +the last sector will be erased. If the offset does not start at the beginning
> +of an erase block, the operation will fail.
> +
> +Speed statistics are shown including the number of bytes that were already
> +correct.
> +
> +
> +Protect
> +~~~~~~~
> +
> +SPI-flash chips often have a protection feature where the chip is split up into
> +regions which can be locked or unlocked. With *sf protect* it is possible to
> +change these settings, if supported by the driver.
> +
> +lock|unlock
> + Selects whether to lock or unlock the sectors
> +
> +<sector>
> + Start sector number to lock/unlock. This may be the byte offset or some
> + other value, depending on the chip.
> +
> +<len>
> + Number of bytes to lock/unlock
> +
> +
> +Test
> +~~~~
> +
> +A convenient and fast *sf test* subcommand provides a way to check that SPI
> +flash is working as expected. This works in four stages:
> +
> + * erase - erases the entire region
> + * check - checks that the region is erased
> + * write - writes a test pattern to the region, consisting of the U-Boot code
> + * read - reads back the test pattern to check that it was written correctly
> +
> +Memory is allocated for two buffers, each <len> bytes in size. At typical
> +size is 64KB to 1MB. The offset and size must be aligned to an erase boundary.
> +
> +Note that this test will fail if any part of the SPI flash is write-protected.
> +
> +
> +Examples
> +--------
> +
> +This first example uses sandbox::
"the sandbox"
> +
> + => sf probe
> + SF: Detected m25p16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB
> + => sf read 1000 1100 80000
> + device 0 offset 0x1100, size 0x80000
> + SF: 524288 bytes @ 0x1100 Read: OK
> + => md 1000
> + 00001000: edfe0dd0 f33a0000 78000000 84250000 ......:....x..%.
> + 00001010: 28000000 11000000 10000000 00000000 ...(............
> + 00001020: 6f050000 0c250000 00000000 00000000 ...o..%.........
> + 00001030: 00000000 00000000 00000000 00000000 ................
> + 00001040: 00000000 00000000 00000000 00000000 ................
> + 00001050: 00000000 00000000 00000000 00000000 ................
> + 00001060: 00000000 00000000 00000000 00000000 ................
> + 00001070: 00000000 00000000 01000000 00000000 ................
> + 00001080: 03000000 04000000 00000000 01000000 ................
> + 00001090: 03000000 04000000 0f000000 01000000 ................
> + 000010a0: 03000000 08000000 1b000000 646e6173 ............sand
> + 000010b0: 00786f62 03000000 08000000 21000000 box............!
> + 000010c0: 646e6173 00786f62 01000000 61696c61 sandbox.....alia
> + 000010d0: 00736573 03000000 07000000 2c000000 ses............,
> + 000010e0: 6332692f 00003040 03000000 07000000 /i2c at 0..........
> + 000010f0: 31000000 6963702f 00003040 03000000 ...1/pci at 0......
> + => sf erase 0 80000
> + SF: 524288 bytes @ 0x0 Erased: OK
> + => sf read 1000 1100 80000
> + device 0 offset 0x1100, size 0x80000
> + SF: 524288 bytes @ 0x1100 Read: OK
> + => md 1000
> + 00001000: ffffffff ffffffff ffffffff ffffffff ................
> + 00001010: ffffffff ffffffff ffffffff ffffffff ................
> + 00001020: ffffffff ffffffff ffffffff ffffffff ................
> + 00001030: ffffffff ffffffff ffffffff ffffffff ................
> + 00001040: ffffffff ffffffff ffffffff ffffffff ................
> + 00001050: ffffffff ffffffff ffffffff ffffffff ................
> + 00001060: ffffffff ffffffff ffffffff ffffffff ................
> + 00001070: ffffffff ffffffff ffffffff ffffffff ................
> + 00001080: ffffffff ffffffff ffffffff ffffffff ................
> + 00001090: ffffffff ffffffff ffffffff ffffffff ................
> + 000010a0: ffffffff ffffffff ffffffff ffffffff ................
> + 000010b0: ffffffff ffffffff ffffffff ffffffff ................
> + 000010c0: ffffffff ffffffff ffffffff ffffffff ................
> + 000010d0: ffffffff ffffffff ffffffff ffffffff ................
> + 000010e0: ffffffff ffffffff ffffffff ffffffff ................
> + 000010f0: ffffffff ffffffff ffffffff ffffffff ................
> +
> +This second example is running on coral, an x86 Chromebook::
Proper names should be capitalized: "Google Coral".
> +
> + => sf probe
> + SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB
> + => sf erase 300000 80000
> + SF: 524288 bytes @ 0x300000 Erased: OK
> + => sf update 1110000 300000 80000
> + device 0 offset 0x300000, size 0x80000
> + 524288 bytes written, 0 bytes skipped in 0.457s, speed 1164578 B/s
> +
> + # This does nothing as the flash is already updated
> + => sf update 1110000 300000 80000
> + device 0 offset 0x300000, size 0x80000
> + 0 bytes written, 524288 bytes skipped in 0.196s, speed 2684354 B/s
> + => sf test 00000 80000 # try a protected region
> + SPI flash test:
> + Erase failed (err = -5)
> + Test failed
> + => sf test 800000 80000
> + SPI flash test:
> + 0 erase: 18 ticks, 28444 KiB/s 227.552 Mbps
> + 1 check: 192 ticks, 2666 KiB/s 21.328 Mbps
> + 2 write: 227 ticks, 2255 KiB/s 18.040 Mbps
> + 3 read: 189 ticks, 2708 KiB/s 21.664 Mbps
> + Test passed
> + 0 erase: 18 ticks, 28444 KiB/s 227.552 Mbps
> + 1 check: 192 ticks, 2666 KiB/s 21.328 Mbps
> + 2 write: 227 ticks, 2255 KiB/s 18.040 Mbps
> + 3 read: 189 ticks, 2708 KiB/s 21.664 Mbps
> +
> +
> +.. _SPI documentation:
> + https://en.wikipedia.org/wiki/Serial_Peripheral_Interface
>
Please, add a section "Configuration" (cf. loady command). For other
commands we also describe the return value of $? to expect.
Best regards
Heinrich
More information about the U-Boot
mailing list