[PATCH 2/2] dt-bindings: u-boot: Add an initial binding for config

Tue Oct 12 17:05:29 CEST 2021

 On Tue, Oct 12, 2021 at 8:41 AM Simon Glass <sjg at chromium.org> wrote:
>
> Hi Rob,
>
> On Mon, 4 Oct 2021 at 13:30, Rob Herring <robh at kernel.org> wrote:
> >
> > On Sun, Oct 03, 2021 at 12:51:53PM -0600, Simon Glass wrote:
> > > U-Boot makes use of the devicetree for its driver model. Devices are bound
> > > based on the hardware description in the devicetree.
> > >
> > > Since U-Boot is not an operating system, it has no command line or user
> > > space to provide configuration and policy information. This must be made
> > > available in some other way.
> > >
> > > Therefore U-Boot uses devicetree for configuration and run-time control
> > > and has done for approximately 9 years. This works extremely well in the
> > > project and is very flexible. However the bindings have never been
> > > incorporated in the devicetree bindings in the Linux tree. This could be
> > > a good time to start this work as we try to create standard bindings for
> > > communicating between firmware components.
> > >
> > > Add an initial binding for this node, covering just the config node, which
> > > is the main requirement. It is similar in concept to the chosen node, but
> > > used for passing information between firmware components, instead of from
> > > firmware to operating system.
> > >
> > > Signed-off-by: Simon Glass <sjg at chromium.org>
> > > ---
> > > Please be kind in your review. Some words about why this is needed are
> > > included in the description in config.yaml file.
> > >
> > > The last attempt to add just one property needed by U-Boot went into the
> > > weeds 6 years ago, with what I see as confusion about the role of the
> > > chosen node in devicetree[1].
> > >
> > > I am trying again in the hope of reaching resolution rather than just
> > > going around in circles with the 'devicetree is a hardware description'
> > > argument :-)
> > >
> > > Quoting from the introduction to latest devicetree spec[2]:
> > >
> > > >>>
> > > To initialize and boot a computer system, various software components
> > > interact. Firmware might perform low-level initialization of the system
> > > hardware before passing control to software such as an operating system,
> > > bootloader, or  hypervisor. Bootloaders and hypervisors can, in turn,
> > > load and transfer control to operating systems. Standard, consistent
> > > interfaces and conventions facilitate the interactions between these
> > > software components. In this document the term boot program is used to
> > > generically refer to a software component that initializes the system
> > > state and executes another software component referred to as a client
> > > program.
> > > <<<
> > >
> > > This clearly envisages multiple software components in the firmware
> > > domain and in fact that is the case today. They need some way to
> > > communicate configuration data such as memory setup, runtime-feature
> > > selection and developer conveniences. Devicetree seems ideal, at least for
> > > components where the performance / memory requirements of devicetree are
> > > affordable.
> > >
> > > I hope that the Linux community (which owns the devicetree bindings) finds
> > > this initiative valuable and acceptable.
> >
> > Owns? I'm having a sale and can make you a good offer. Buy 1 binding,
> > get 2000 free. :)
>
> Yes, it's the price of that first binding that surely puts everyone off.
>
> (sorry for sitting on this for a week, my spam filter doesn't like
> some mailing lists and I'm working on it)
>
> >
> > >
> > > [1] https://lists.denx.de/pipermail/u-boot/2015-July/218585.html
> > > [2] https://github.com/devicetree-org/devicetree-specification/releases/tag/v0.3
> > >
> > >  .../devicetree/bindings/u-boot/config.yaml    | 137 ++++++++++++++++++
> > >  1 file changed, 137 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/u-boot/config.yaml
> >
> > Might as well put this into dt-schema rather than the kernel. But might
> > get more review here first.
>
> OK, so does that mean a PR to https://github.com/robherring/dt-schema

Wrong one: https://github.com/devicetree-org/dt-schema

I need to update the readme there for the old one.

> or is there a mailing list for it? I think I am missing some
> understanding here.

You can send a PR or to a DT mailing list, but the mail list will get
more reviews (hopefully). devicetree-spec is better than devicetree as
it is not a firehose.

> >
> > > diff --git a/Documentation/devicetree/bindings/u-boot/config.yaml b/Documentation/devicetree/bindings/u-boot/config.yaml
> > > new file mode 100644
> > > index 00000000000000..336577a17fdf5a
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/u-boot/config.yaml
> > > @@ -0,0 +1,137 @@
> > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/u-boot/config.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: U-Boot configuration node
> > > +
> > > +maintainers:
> > > +  - Simon Glass <sjg at chromium.org>
> > > +
> > > +description: |
> > > +  The config node does not represent a real device, but serves as a place
> > > +  for passing data between firmware elements, like memory maps. Data in the
> > > +  config node does not represent the hardware. It is ignored by operating
> > > +  systems.
> > > +
> > > +  Purpose of config node
> > > +  ----------------------
> > > +
> > > +  A common problem with firmware is that many builds are needed to deal with the
> > > +  slight variations between different, related models. For example, one model
> > > +  may have a TPM and another may not. Devicetree provides an excellent solution
> > > +  to this problem, in that the devicetree to actually use on a platform can be
> > > +  injected in the factory based on which model is being manufactured at the time.
> > > +
> > > +  A related problem causing build proliferation is dealing with the differences
> > > +  between development firmware, developer-friendly firmware (e.g. with all
> > > +  security features present but with the ability to access the command line),
> > > +  test firmware (which runs tests used in the factory), final production
> > > +  firmware (before signing), signed firmware (where the signatures have been
> > > +  inserted) and the like. Ideally all or most of these should use the same
> > > +  U-Boot build, with just some options to determine the features available. For
> > > +  example, being able to control whether the UART console or JTAG are available,
> > > +  on any image, is a great debugging aid.
> > > +
> > > +  When the firmware consists of multiple parts (various U-Boot phases, TF-A,
> > > +  OP-TEE), it is helpful that all operate the same way at runtime, regardless of
> > > +  how they were built. This can be achieved by passing the runtime configuration
> > > +  (e.g. 'enable UART console', 'here are your public keys') along the chain
> > > +  through each firmware stage. It is frustrating to have to replicate a bug on
> > > +  production firmware which does happen on developer firmware, because they are
> > > +  completely different builds.
> > > +
> > > +  The config node provides useful functionality for this. It allows the different
> > > +  controls to be 'factored out' of the U-Boot binary, so they can be controlled
> > > +  separately from the initial source-code build. The node can be easily updated
> > > +  by a build or factory tool and can control various features in U-Boot. It is
> > > +  similar in concept to a Kconfig option, except that it can be changed after
> > > +  U-Boot is built.
> > > +
> > > +  The config node is similar in concept to /chosen (see chosen.txt) except that
> >
> > chosen.yaml now (in dt-schema).
>
> OK
>
> >
> > > +  it is for passing information *into* and *between) firmware components,
> > > +  instead of from firmware to the Operating System. Also, while operating
> > > +  systems typically have a (sometimes extremely long) command line, U-Boot does
> > > +  not support this, except with sandbox. The devicetree provides a more
> > > +  structured approach in any case.
> >
> > What about having a /chosen/u-boot/ node instead?
>
> What is your rationale for doing that?

Simply that /chosen is where the s/w configuration for the next stage
consuming the DT goes. Also, we already have bootcmd defined in chosen
and don't need it in a whole other place.

Arguably, we don't even need another sub-node here. We could just say
a given component is responsible for consuming /chosen and then
updating it for the next component. The problem with that is if you
want all the configuration to coexist at the start. Overlapping
properties is also a problem. The only overlap in this case is
bootcmd, but you could handle that with a 'u-boot,bootcmd'. Not saying
we should do that though given we need to extend things beyond 2
components.

> Should we perhaps have a vendor/ directory for vendor-specific tags?

In the kernel tree, we already have bindings/soc/<vendor> and vendors
like to just dump all their stuff there when it belongs in a directory
for the function.

> Also, thinking ahead, I am interested in how we can add bindings for
> firmware-to-firmware communications. There are some settings that
> could be defined across projects (such as memory layout, security
> level/settings) and these should ideally be harmless to pass to the
> kernel (i.e. ignored by the kernel). It is possible that some of these
> could be used by the kernel but then we can always recreate them using
> kernel bindings as needed (and cross that bridge when we come to it).
> So this would be a set of bindings used by firmware components in
> general. We would not want to use "u-boot,xxx" in that case.

Yes, that is also why I'm thinking about how do we extend /chosen.
More generally, it's just one stage to the next. firmware-to-firmware
is not really any different than bootloader to OS. /chosen serves that
purpose already, so the question is how to make chosen support
multiple components.

Rob