[PATCH 07/16] arm: rpi: Add a devicetree file for rpi_4
François Ozog
francois.ozog at linaro.org
Wed Oct 13 03:24:59 CEST 2021
Hi Simon
This is making a clean environment go in the wrong direction. I have
witnessed that bus to mmio changed for instance, have seen patches to patch
live u-boot embedded DT because it does not do the work that Videocore
does.
The Videocore handles that properly so why adding this?
Si i would agree to have the file on the documentation directory not on the
dts with the same warning I mentioned earlier
Le mer. 13 oct. 2021 à 03:03, Simon Glass <sjg at chromium.org> a écrit :
> Add this file, obtained from the Raspbian boot disk, so there is a
> reference devicetree in the U-Boot tree. The same one is used for
> 32- and 64-bit variants.
>
> Note that U-Boot does not normally need this at runtime, since
> CONFIG_OF_BOARD is enabled. The previous firmware stage provides a
> devicetree at runtime.
>
> Signed-off-by: Simon Glass <sjg at chromium.org>
> ---
>
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/bcm2711-rpi-4-b.dts | 1958 ++++++++++++++++++++++++++++++
> configs/rpi_4_32b_defconfig | 1 +
> configs/rpi_4_defconfig | 1 +
> configs/rpi_arm64_defconfig | 1 +
> 5 files changed, 1963 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/bcm2711-rpi-4-b.dts
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 52c586f3974..efc01a70bf2 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -1062,7 +1062,8 @@ dtb-$(CONFIG_ARCH_BCM283X) += \
> bcm2837-rpi-3-a-plus.dtb \
> bcm2837-rpi-3-b.dtb \
> bcm2837-rpi-3-b-plus.dtb \
> - bcm2837-rpi-cm3-io3.dtb
> + bcm2837-rpi-cm3-io3.dtb \
> + bcm2711-rpi-4-b.dtb
>
> dtb-$(CONFIG_ARCH_BCM63158) += \
> bcm963158.dtb
> diff --git a/arch/arm/dts/bcm2711-rpi-4-b.dts
> b/arch/arm/dts/bcm2711-rpi-4-b.dts
> new file mode 100644
> index 00000000000..425e9fb91c4
> --- /dev/null
> +++ b/arch/arm/dts/bcm2711-rpi-4-b.dts
> @@ -0,0 +1,1958 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR MIT
> +/*
> + * Sample device tree for rpi_4
> +
> + * Copyright 2021 Google LLC
> + */
> +
> +/dts-v1/;
> +
> +/memreserve/ 0x0000000000000000 0x0000000000001000;
> +/ {
> + compatible = "raspberrypi,4-model-b\0brcm,bcm2838\0brcm,bcm2837";
> + model = "Raspberry Pi 4 Model B";
> + interrupt-parent = <0x01>;
> + #address-cells = <0x02>;
> + #size-cells = <0x01>;
> +
> + aliases {
> + serial0 = "/soc/serial at 7e215040";
> + serial1 = "/soc/serial at 7e201000";
> + audio = "/soc/audio";
> + aux = "/soc/aux at 7e215000";
> + sound = "/soc/sound";
> + soc = "/soc";
> + dma = "/soc/dma at 7e007000";
> + watchdog = "/soc/watchdog at 7e100000";
> + random = "/soc/rng at 7e104000";
> + mailbox = "/soc/mailbox at 7e00b880";
> + gpio = "/soc/gpio at 7e200000";
> + uart0 = "/soc/serial at 7e201000";
> + sdhost = "/soc/mmc at 7e202000";
> + mmc0 = "/soc/emmc2 at 7e340000";
> + i2s = "/soc/i2s at 7e203000";
> + spi0 = "/soc/spi at 7e204000";
> + i2c0 = "/soc/i2c at 7e205000";
> + uart1 = "/soc/serial at 7e215040";
> + spi1 = "/soc/spi at 7e215080";
> + spi2 = "/soc/spi at 7e2150c0";
> + mmc = "/soc/mmc at 7e300000";
> + mmc1 = "/soc/mmcnr at 7e300000";
> + i2c1 = "/soc/i2c at 7e804000";
> + i2c2 = "/soc/i2c at 7e805000";
> + usb = "/soc/usb at 7e980000";
> + leds = "/leds";
> + fb = "/soc/fb";
> + thermal = "/soc/thermal at 7d5d2200";
> + axiperf = "/soc/axiperf";
> + mmc2 = "/soc/mmc at 7e202000";
> + ethernet0 = "/scb/genet at 7d580000";
> + };
> +
> + chosen {
> + bootargs = "8250.nr_uarts=1 cma=64M";
> + };
> +
> + thermal-zones {
> +
> + cpu-thermal {
> + polling-delay-passive = <0x00>;
> + polling-delay = <0x3e8>;
> + thermal-sensors = <0x02>;
> + coefficients = <0xfffffe19 0x641b8>;
> + phandle = <0x2f>;
> +
> + cooling-maps {
> + };
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <0x01>;
> + #size-cells = <0x01>;
> + ranges = <0x7e000000 0x00 0xfe000000 0x1800000
> + 0x7c000000 0x00 0xfc000000 0x2000000
> + 0x40000000 0x00 0xff800000 0x800000>;
> + dma-ranges = <0xc0000000 0x00 0x00 0x3c000000>;
> + phandle = <0x30>;
> +
> + txp at 7e004000 {
> + compatible = "brcm,bcm2835-txp";
> + reg = <0x7e004000 0x20>;
> + interrupts = <0x00 0x4b 0x04>;
> + status = "disabled";
> + phandle = <0x31>;
> + };
> +
> + dma at 7e007000 {
> + compatible = "brcm,bcm2835-dma";
> + reg = <0x7e007000 0xb00>;
> + interrupts = <0x00 0x50 0x04 0x00 0x51 0x04 0x00
> 0x52
> + 0x04 0x00 0x53 0x04 0x00 0x54 0x04 0x00
> + 0x55 0x04 0x00 0x56 0x04 0x00 0x57 0x04
> + 0x00 0x57 0x04 0x00 0x58 0x04 0x00 0x58
> + 0x04>;
> + interrupt-names =
> "dma0\0dma1\0dma2\0dma3\0dma4\0dma5\0dma6\0dma7\0dma8\0dma9\0dma10";
> + #dma-cells = <0x01>;
> + brcm,dma-channel-mask = <0x7ef5>;
> + phandle = <0x0a>;
> + };
> +
> + watchdog at 7e100000 {
> + compatible =
> "brcm,bcm2835-pm\0brcm,bcm2835-pm-wdt";
> + #power-domain-cells = <0x01>;
> + #reset-cells = <0x01>;
> + reg = <0x7e100000 0x114 0x7e00a000 0x24 0x7ec11000
> 0x20>;
> + clocks = <0x03 0x15 0x03 0x1d 0x03 0x17 0x03 0x16>;
> + clock-names = "v3d\0peri_image\0h264\0isp";
> + system-power-controller;
> + phandle = <0x1c>;
> + };
> +
> + cprman at 7e101000 {
> + compatible = "brcm,bcm2838-cprman";
> + #clock-cells = <0x01>;
> + reg = <0x7e101000 0x2000>;
> + clocks = <0x04 0x05 0x00 0x05 0x01 0x05 0x02 0x06
> + 0x00 0x06 0x01 0x06 0x02>;
> + firmware = <0x07>;
> + phandle = <0x03>;
> + };
> +
> + rng at 7e104000 {
> + compatible = "brcm,bcm2838-rng200";
> + reg = <0x7e104000 0x10>;
> + interrupts = <0x00 0x7d 0x04>;
> + phandle = <0x26>;
> + };
> +
> + mailbox at 7e00b880 {
> + compatible = "brcm,bcm2835-mbox";
> + reg = <0x7e00b880 0x40>;
> + interrupts = <0x00 0x21 0x04>;
> + #mbox-cells = <0x00>;
> + phandle = <0x1a>;
> + };
> +
> + gpio: gpio at 7e200000 {
> + compatible = "brcm,bcm2835-gpio";
> + reg = <0x7e200000 0xb4>;
> + interrupts = <0x00 0x71 0x04 0x00 0x72 0x04>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> + interrupt-controller;
> + #interrupt-cells = <0x02>;
> + phandle = <0x0f>;
> +
> + dpi_gpio0 {
> + brcm,pins = <0x00 0x01 0x02 0x03 0x04
> + 0x05 0x06 0x07 0x08 0x09
> + 0x0a 0x0b 0x0c 0x0d 0x0e
> + 0x0f 0x10 0x11 0x12 0x13
> + 0x14 0x15 0x16 0x17 0x18
> + 0x19 0x1a 0x1b>;
> + brcm,function = <0x06>;
> + phandle = <0x32>;
> + };
> +
> + emmc_gpio22 {
> + brcm,pins = <0x16 0x17 0x18 0x19 0x1a
> 0x1b>;
> + brcm,function = <0x07>;
> + phandle = <0x33>;
> + };
> +
> + emmc_gpio34 {
> + brcm,pins = <0x22 0x23 0x24 0x25 0x26
> 0x27>;
> + brcm,function = <0x07>;
> + brcm,pull = <0x00 0x02 0x02 0x02 0x02
> 0x02>;
> + phandle = <0x34>;
> + };
> +
> + emmc_gpio48 {
> + brcm,pins = <0x30 0x31 0x32 0x33 0x34
> 0x35>;
> + brcm,function = <0x07>;
> + phandle = <0x35>;
> + };
> +
> + gpclk0_gpio4 {
> + brcm,pins = <0x04>;
> + brcm,function = <0x04>;
> + phandle = <0x36>;
> + };
> +
> + gpclk1_gpio5 {
> + brcm,pins = <0x05>;
> + brcm,function = <0x04>;
> + phandle = <0x37>;
> + };
> +
> + gpclk1_gpio42 {
> + brcm,pins = <0x2a>;
> + brcm,function = <0x04>;
> + phandle = <0x38>;
> + };
> +
> + gpclk1_gpio44 {
> + brcm,pins = <0x2c>;
> + brcm,function = <0x04>;
> + phandle = <0x39>;
> + };
> +
> + gpclk2_gpio6 {
> + brcm,pins = <0x06>;
> + brcm,function = <0x04>;
> + phandle = <0x3a>;
> + };
> +
> + gpclk2_gpio43 {
> + brcm,pins = <0x2b>;
> + brcm,function = <0x04>;
> + brcm,pull = <0x00>;
> + phandle = <0x3b>;
> + };
> +
> + i2c0_gpio0 {
> + brcm,pins = <0x00 0x01>;
> + brcm,function = <0x04>;
> + phandle = <0x3c>;
> + };
> +
> + i2c0_gpio28 {
> + brcm,pins = <0x1c 0x1d>;
> + brcm,function = <0x04>;
> + phandle = <0x3d>;
> + };
> +
> + i2c0_gpio44 {
> + brcm,pins = <0x2c 0x2d>;
> + brcm,function = <0x05>;
> + phandle = <0x3e>;
> + };
> +
> + i2c1_gpio2 {
> + brcm,pins = <0x02 0x03>;
> + brcm,function = <0x04>;
> + phandle = <0x3f>;
> + };
> +
> + i2c1_gpio44 {
> + brcm,pins = <0x2c 0x2d>;
> + brcm,function = <0x06>;
> + phandle = <0x40>;
> + };
> +
> + jtag_gpio22 {
> + brcm,pins = <0x16 0x17 0x18 0x19 0x1a
> 0x1b>;
> + brcm,function = <0x03>;
> + phandle = <0x41>;
> + };
> +
> + pcm_gpio18 {
> + brcm,pins = <0x12 0x13 0x14 0x15>;
> + brcm,function = <0x04>;
> + phandle = <0x42>;
> + };
> +
> + pcm_gpio28 {
> + brcm,pins = <0x1c 0x1d 0x1e 0x1f>;
> + brcm,function = <0x06>;
> + phandle = <0x43>;
> + };
> +
> + pwm0_gpio12 {
> + brcm,pins = <0x0c>;
> + brcm,function = <0x04>;
> + phandle = <0x44>;
> + };
> +
> + pwm0_gpio18 {
> + brcm,pins = <0x12>;
> + brcm,function = <0x02>;
> + phandle = <0x45>;
> + };
> +
> + pwm0_gpio40 {
> + brcm,pins = <0x28>;
> + brcm,function = <0x04>;
> + phandle = <0x46>;
> + };
> +
> + pwm1_gpio13 {
> + brcm,pins = <0x0d>;
> + brcm,function = <0x04>;
> + phandle = <0x47>;
> + };
> +
> + pwm1_gpio19 {
> + brcm,pins = <0x13>;
> + brcm,function = <0x02>;
> + phandle = <0x48>;
> + };
> +
> + pwm1_gpio41 {
> + brcm,pins = <0x29>;
> + brcm,function = <0x04>;
> + phandle = <0x49>;
> + };
> +
> + pwm1_gpio45 {
> + brcm,pins = <0x2d>;
> + brcm,function = <0x04>;
> + phandle = <0x4a>;
> + };
> +
> + sdhost_gpio48 {
> + brcm,pins = <0x16 0x17 0x18 0x19 0x1a
> 0x1b>;
> + brcm,function = <0x04>;
> + phandle = <0x0b>;
> + };
> +
> + spi0_gpio7 {
> + brcm,pins = <0x07 0x08 0x09 0x0a 0x0b>;
> + brcm,function = <0x04>;
> + phandle = <0x4b>;
> + };
> +
> + spi0_gpio35 {
> + brcm,pins = <0x23 0x24 0x25 0x26 0x27>;
> + brcm,function = <0x04>;
> + phandle = <0x4c>;
> + };
> +
> + spi1_gpio16 {
> + brcm,pins = <0x10 0x11 0x12 0x13 0x14
> 0x15>;
> + brcm,function = <0x03>;
> + phandle = <0x4d>;
> + };
> +
> + spi2_gpio40 {
> + brcm,pins = <0x28 0x29 0x2a 0x2b 0x2c
> 0x2d>;
> + brcm,function = <0x03>;
> + phandle = <0x4e>;
> + };
> +
> + uart0_gpio14: uart0_gpio14 {
> + brcm,pins = <0x0e 0x0f>;
> + brcm,function = <0x04>;
> + phandle = <0x4f>;
> + };
> +
> + uart0: uart0_ctsrts_gpio16 {
> + brcm,pins = <0x10 0x11>;
> + brcm,function = <0x07>;
> + phandle = <0x50>;
> + };
> +
> + uart0_ctsrts_gpio30 {
> + brcm,pins = <0x1e 0x1f>;
> + brcm,function = <0x07>;
> + brcm,pull = <0x02 0x00>;
> + phandle = <0x51>;
> + };
> +
> + uart0_gpio32 {
> + brcm,pins = <0x20 0x21>;
> + brcm,function = <0x07>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x52>;
> + };
> +
> + uart0_gpio36 {
> + brcm,pins = <0x24 0x25>;
> + brcm,function = <0x06>;
> + phandle = <0x53>;
> + };
> +
> + uart0_ctsrts_gpio38 {
> + brcm,pins = <0x26 0x27>;
> + brcm,function = <0x06>;
> + phandle = <0x54>;
> + };
> +
> + uart1_gpio14: uart1_gpio14 {
> + brcm,pins = <0x0e 0x0f>;
> + brcm,function = <0x02>;
> + phandle = <0x55>;
> + };
> +
> + uart1: uart1_ctsrts_gpio16 {
> + brcm,pins = <0x10 0x11>;
> + brcm,function = <0x02>;
> + phandle = <0x56>;
> + };
> +
> + uart1_gpio32 {
> + brcm,pins = <0x20 0x21>;
> + brcm,function = <0x02>;
> + phandle = <0x57>;
> + };
> +
> + uart1_ctsrts_gpio30 {
> + brcm,pins = <0x1e 0x1f>;
> + brcm,function = <0x02>;
> + phandle = <0x58>;
> + };
> +
> + uart1_gpio40 {
> + brcm,pins = <0x28 0x29>;
> + brcm,function = <0x02>;
> + phandle = <0x59>;
> + };
> +
> + uart1_ctsrts_gpio42 {
> + brcm,pins = <0x2a 0x2b>;
> + brcm,function = <0x02>;
> + phandle = <0x5a>;
> + };
> +
> + gpclk0_gpio49 {
> + brcm,pins = <0x31>;
> + brcm,function = <0x05>;
> + brcm,pull = <0x00>;
> + phandle = <0x5b>;
> + };
> +
> + gpclk1_gpio50 {
> + brcm,pins = <0x32>;
> + brcm,function = <0x05>;
> + brcm,pull = <0x00>;
> + phandle = <0x5c>;
> + };
> +
> + gpclk2_gpio51 {
> + brcm,pins = <0x33>;
> + brcm,function = <0x05>;
> + brcm,pull = <0x00>;
> + phandle = <0x5d>;
> + };
> +
> + i2c0_gpio46 {
> + brcm,pins = <0x2e 0x2f>;
> + brcm,function = <0x04>;
> + phandle = <0x5e>;
> + };
> +
> + i2c1_gpio46 {
> + brcm,pins = <0x2e 0x2f>;
> + brcm,function = <0x05>;
> + phandle = <0x5f>;
> + };
> +
> + i2c3_gpio2 {
> + brcm,pins = <0x02 0x03>;
> + brcm,function = <0x02>;
> + phandle = <0x60>;
> + };
> +
> + i2c3_gpio4 {
> + brcm,pins = <0x04 0x05>;
> + brcm,function = <0x02>;
> + phandle = <0x61>;
> + };
> +
> + i2c4_gpio6 {
> + brcm,pins = <0x06 0x07>;
> + brcm,function = <0x02>;
> + phandle = <0x62>;
> + };
> +
> + i2c4_gpio8 {
> + brcm,pins = <0x08 0x09>;
> + brcm,function = <0x02>;
> + phandle = <0x63>;
> + };
> +
> + i2c5_gpio10 {
> + brcm,pins = <0x0a 0x0b>;
> + brcm,function = <0x02>;
> + phandle = <0x64>;
> + };
> +
> + i2c5_gpio12 {
> + brcm,pins = <0x0c 0x0d>;
> + brcm,function = <0x02>;
> + phandle = <0x65>;
> + };
> +
> + i2c6_gpio0 {
> + brcm,pins = <0x00 0x01>;
> + brcm,function = <0x02>;
> + phandle = <0x66>;
> + };
> +
> + i2c6_gpio22 {
> + brcm,pins = <0x16 0x17>;
> + brcm,function = <0x02>;
> + phandle = <0x67>;
> + };
> +
> + i2c_slave_gpio8 {
> + brcm,pins = <0x08 0x09 0x0a 0x0b>;
> + brcm,function = <0x07>;
> + phandle = <0x68>;
> + };
> +
> + jtag_gpio48 {
> + brcm,pins = <0x30 0x31 0x32 0x33 0x34
> 0x35>;
> + brcm,function = <0x03>;
> + phandle = <0x69>;
> + };
> +
> + mii_gpio28 {
> + brcm,pins = <0x1c 0x1d 0x1e 0x1f>;
> + brcm,function = <0x03>;
> + phandle = <0x6a>;
> + };
> +
> + mii_gpio36 {
> + brcm,pins = <0x24 0x25 0x26 0x27>;
> + brcm,function = <0x02>;
> + phandle = <0x6b>;
> + };
> +
> + pcm_gpio50 {
> + brcm,pins = <0x32 0x33 0x34 0x35>;
> + brcm,function = <0x06>;
> + phandle = <0x6c>;
> + };
> +
> + pwm0_gpio52 {
> + brcm,pins = <0x34>;
> + brcm,function = <0x05>;
> + brcm,pull = <0x00>;
> + phandle = <0x6d>;
> + };
> +
> + pwm1_gpio53 {
> + brcm,pins = <0x35>;
> + brcm,function = <0x05>;
> + brcm,pull = <0x00>;
> + phandle = <0x6e>;
> + };
> +
> + rgmii_gpio35 {
> + brcm,pins = <0x23 0x24>;
> + brcm,function = <0x03>;
> + phandle = <0x6f>;
> + };
> +
> + rgmii_irq_gpio34 {
> + brcm,pins = <0x22>;
> + brcm,function = <0x02>;
> + phandle = <0x70>;
> + };
> +
> + rgmii_irq_gpio39 {
> + brcm,pins = <0x27>;
> + brcm,function = <0x03>;
> + phandle = <0x71>;
> + };
> +
> + rgmii_mdio_gpio28 {
> + brcm,pins = <0x1c 0x1d>;
> + brcm,function = <0x02>;
> + phandle = <0x72>;
> + };
> +
> + rgmii_mdio_gpio37 {
> + brcm,pins = <0x25 0x26>;
> + brcm,function = <0x03>;
> + phandle = <0x73>;
> + };
> +
> + spi0_gpio46 {
> + brcm,pins = <0x2e 0x2f 0x30 0x31>;
> + brcm,function = <0x06>;
> + phandle = <0x74>;
> + };
> +
> + spi2_gpio46 {
> + brcm,pins = <0x2e 0x2f 0x30 0x31 0x32>;
> + brcm,function = <0x02>;
> + phandle = <0x75>;
> + };
> +
> + spi3_gpio0 {
> + brcm,pins = <0x00 0x01 0x02 0x03>;
> + brcm,function = <0x07>;
> + phandle = <0x76>;
> + };
> +
> + spi4_gpio4 {
> + brcm,pins = <0x04 0x05 0x06 0x07>;
> + brcm,function = <0x07>;
> + phandle = <0x77>;
> + };
> +
> + spi5_gpio12 {
> + brcm,pins = <0x0c 0x0d 0x0e 0x0f>;
> + brcm,function = <0x07>;
> + phandle = <0x78>;
> + };
> +
> + spi6_gpio18 {
> + brcm,pins = <0x12 0x13 0x14 0x15>;
> + brcm,function = <0x07>;
> + phandle = <0x79>;
> + };
> +
> + uart2_gpio0 {
> + brcm,pins = <0x00 0x01>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x7a>;
> + };
> +
> + uart2_ctsrts_gpio2 {
> + brcm,pins = <0x02 0x03>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x02 0x00>;
> + phandle = <0x7b>;
> + };
> +
> + uart3_gpio4 {
> + brcm,pins = <0x04 0x05>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x7c>;
> + };
> +
> + uart3_ctsrts_gpio6 {
> + brcm,pins = <0x06 0x07>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x02 0x00>;
> + phandle = <0x7d>;
> + };
> +
> + uart4_gpio8 {
> + brcm,pins = <0x08 0x09>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x7e>;
> + };
> +
> + uart4_ctsrts_gpio10 {
> + brcm,pins = <0x0a 0x0b>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x02 0x00>;
> + phandle = <0x7f>;
> + };
> +
> + uart5_gpio12 {
> + brcm,pins = <0x0c 0x0d>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x80>;
> + };
> +
> + uart5_ctsrts_gpio14 {
> + brcm,pins = <0x0e 0x0f>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x02 0x00>;
> + phandle = <0x81>;
> + };
> +
> + dpi_18bit_gpio0 {
> + brcm,pins = <0x00 0x01 0x02 0x03
> + 0x04 0x05 0x06 0x07
> + 0x08 0x09 0x0a 0x0b
> + 0x0c 0x0d 0x0e 0x0f
> + 0x10 0x11 0x12 0x13
> + 0x14 0x15>;
> + brcm,function = <0x06>;
> + phandle = <0x82>;
> + };
> +
> + spi0_pins {
> + brcm,pins = <0x09 0x0a 0x0b>;
> + brcm,function = <0x04>;
> + phandle = <0x0d>;
> + };
> +
> + spi0_cs_pins {
> + brcm,pins = <0x08 0x07>;
> + brcm,function = <0x01>;
> + phandle = <0x0e>;
> + };
> +
> + spi3_pins {
> + brcm,pins = <0x01 0x02 0x03>;
> + brcm,function = <0x07>;
> + phandle = <0x83>;
> + };
> +
> + spi3_cs_pins {
> + brcm,pins = <0x00 0x18>;
> + brcm,function = <0x01>;
> + phandle = <0x84>;
> + };
> +
> + spi4_pins {
> + brcm,pins = <0x05 0x06 0x07>;
> + brcm,function = <0x07>;
> + phandle = <0x85>;
> + };
> +
> + spi4_cs_pins {
> + brcm,pins = <0x04 0x19>;
> + brcm,function = <0x01>;
> + phandle = <0x86>;
> + };
> +
> + spi5_pins {
> + brcm,pins = <0x0d 0x0e 0x0f>;
> + brcm,function = <0x07>;
> + phandle = <0x87>;
> + };
> +
> + spi5_cs_pins {
> + brcm,pins = <0x0c 0x1a>;
> + brcm,function = <0x01>;
> + phandle = <0x88>;
> + };
> +
> + spi6_pins {
> + brcm,pins = <0x13 0x14 0x15>;
> + brcm,function = <0x07>;
> + phandle = <0x89>;
> + };
> +
> + spi6_cs_pins {
> + brcm,pins = <0x12 0x1b>;
> + brcm,function = <0x01>;
> + phandle = <0x8a>;
> + };
> +
> + i2c0 {
> + brcm,pins = <0x00 0x01>;
> + brcm,function = <0x04>;
> + phandle = <0x10>;
> + };
> +
> + i2c1 {
> + brcm,pins = <0x02 0x03>;
> + brcm,function = <0x04>;
> + phandle = <0x14>;
> + };
> +
> + i2c3 {
> + brcm,pins = <0x04 0x05>;
> + brcm,function = <0x02>;
> + phandle = <0x8b>;
> + };
> +
> + i2c4 {
> + brcm,pins = <0x08 0x09>;
> + brcm,function = <0x02>;
> + phandle = <0x8c>;
> + };
> +
> + i2c5 {
> + brcm,pins = <0x0c 0x0d>;
> + brcm,function = <0x02>;
> + phandle = <0x8d>;
> + };
> +
> + i2c6 {
> + brcm,pins = <0x16 0x17>;
> + brcm,function = <0x02>;
> + phandle = <0x8e>;
> + };
> +
> + i2s {
> + brcm,pins = <0x12 0x13 0x14 0x15>;
> + brcm,function = <0x04>;
> + phandle = <0x0c>;
> + };
> +
> + sdio_pins {
> + brcm,pins = <0x22 0x23 0x24 0x25 0x26
> 0x27>;
> + brcm,function = <0x07>;
> + brcm,pull = <0x00 0x02 0x02 0x02 0x02
> 0x02>;
> + phandle = <0x19>;
> + };
> +
> + bt_pins {
> + brcm,pins = [2d 00];
> + brcm,function = <0x00>;
> + brcm,pull = <0x02>;
> + phandle = <0x09>;
> + };
> +
> + uart0_pins {
> + brcm,pins = <0x20 0x21>;
> + brcm,function = <0x07>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x08>;
> + };
> +
> + uart1_pins {
> + brcm,pins;
> + brcm,function;
> + brcm,pull;
> + phandle = <0x12>;
> + };
> +
> + uart2_pins {
> + brcm,pins = <0x00 0x01>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x8f>;
> + };
> +
> + uart3_pins {
> + brcm,pins = <0x04 0x05>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x90>;
> + };
> +
> + uart4_pins {
> + brcm,pins = <0x08 0x09>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x91>;
> + };
> +
> + uart5_pins {
> + brcm,pins = <0x0c 0x0d>;
> + brcm,function = <0x03>;
> + brcm,pull = <0x00 0x02>;
> + phandle = <0x92>;
> + };
> +
> + audio_pins {
> + brcm,pins = <0x28 0x29>;
> + brcm,function = <0x04>;
> + phandle = <0x1b>;
> + };
> + };
> +
> + serial at 7e201000 {
> + compatible =
> "brcm,bcm2835-pl011\0arm,pl011\0arm,primecell";
> + reg = <0x7e201000 0x200>;
> + interrupts = <0x00 0x79 0x04>;
> + clocks = <0x03 0x13 0x03 0x14>;
> + clock-names = "uartclk\0apb_pclk";
> + arm,primecell-periphid = <0x241011>;
> + cts-event-workaround;
> + pinctrl-names = "default";
> + pinctrl-0 = <0x08 0x09>;
> + status = "okay";
> + phandle = <0x1f>;
> + };
> +
> + mmc at 7e202000 {
> + compatible = "brcm,bcm2835-sdhost";
> + reg = <0x7e202000 0x100>;
> + interrupts = <0x00 0x78 0x04>;
> + clocks = <0x03 0x14>;
> + dmas = <0x0a 0x2000000d>;
> + dma-names = "rx-tx";
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x0b>;
> + bus-width = <0x04>;
> + brcm,overclock-50 = <0x00>;
> + brcm,pio-limit = <0x01>;
> + phandle = <0x27>;
> + };
> +
> + i2s at 7e203000 {
> + compatible = "brcm,bcm2835-i2s";
> + reg = <0x7e203000 0x24>;
> + clocks = <0x03 0x1f>;
> + dmas = <0x0a 0x02 0x0a 0x03>;
> + dma-names = "tx\0rx";
> + status = "disabled";
> + #sound-dai-cells = <0x00>;
> + pinctrl-names = "default";
> + pinctrl-0 = <0x0c>;
> + phandle = <0x21>;
> + };
> +
> + spi at 7e204000 {
> + compatible = "brcm,bcm2835-spi";
> + reg = <0x7e204000 0x200>;
> + interrupts = <0x00 0x76 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + dmas = <0x0a 0x06 0x0a 0x07>;
> + dma-names = "tx\0rx";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x0d 0x0e>;
> + cs-gpios = <0x0f 0x08 0x01 0x0f 0x07 0x01>;
> + phandle = <0x22>;
> +
> + spidev at 0 {
> + compatible = "spidev";
> + reg = <0x00>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + spi-max-frequency = <0x7735940>;
> + phandle = <0x93>;
> + };
> +
> + spidev at 1 {
> + compatible = "spidev";
> + reg = <0x01>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + spi-max-frequency = <0x7735940>;
> + phandle = <0x94>;
> + };
> + };
> +
> + i2c at 7e205000 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e205000 0x200>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x10>;
> + clock-frequency = <0x186a0>;
> + phandle = <0x23>;
> + };
> +
> + pixelvalve at 7e206000 {
> + compatible = "brcm,bcm2835-pixelvalve0";
> + reg = <0x7e206000 0x100>;
> + interrupts = <0x00 0x6d 0x04>;
> + status = "disabled";
> + phandle = <0x95>;
> + };
> +
> + pixelvalve at 7e207000 {
> + compatible = "brcm,bcm2835-pixelvalve1";
> + reg = <0x7e207000 0x100>;
> + interrupts = <0x00 0x6e 0x04>;
> + status = "disabled";
> + phandle = <0x96>;
> + };
> +
> + dpi at 7e208000 {
> + compatible = "brcm,bcm2835-dpi";
> + reg = <0x7e208000 0x8c>;
> + clocks = <0x03 0x14 0x03 0x2c>;
> + clock-names = "core\0pixel";
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0x97>;
> + };
> +
> + dsi at 7e209000 {
> + compatible = "brcm,bcm2835-dsi0";
> + reg = <0x7e209000 0x78>;
> + interrupts = <0x00 0x64 0x04>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + #clock-cells = <0x01>;
> + clocks = <0x03 0x20 0x03 0x2f 0x03 0x31>;
> + clock-names = "phy\0escape\0pixel";
> + clock-output-names =
> "dsi0_byte\0dsi0_ddr2\0dsi0_ddr";
> + phandle = <0x05>;
> + };
> +
> + aux at 7e215000 {
> + compatible = "brcm,bcm2835-aux";
> + #clock-cells = <0x01>;
> + reg = <0x7e215000 0x08>;
> + clocks = <0x03 0x14>;
> + phandle = <0x11>;
> + };
> +
> + serial at 7e215040 {
> + compatible = "brcm,bcm2835-aux-uart";
> + reg = <0x7e215040 0x40>;
> + interrupts = <0x00 0x5d 0x04>;
> + clocks = <0x11 0x00>;
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x12>;
> + phandle = <0x20>;
> + };
> +
> + spi at 7e215080 {
> + compatible = "brcm,bcm2835-aux-spi";
> + reg = <0x7e215080 0x40>;
> + interrupts = <0x00 0x5d 0x04>;
> + clocks = <0x11 0x01>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0x98>;
> + };
> +
> + spi at 7e2150c0 {
> + compatible = "brcm,bcm2835-aux-spi";
> + reg = <0x7e2150c0 0x40>;
> + interrupts = <0x00 0x5d 0x04>;
> + clocks = <0x11 0x02>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0x99>;
> + };
> +
> + pwm at 7e20c000 {
> + compatible = "brcm,bcm2835-pwm";
> + reg = <0x7e20c000 0x28>;
> + clocks = <0x03 0x1e>;
> + assigned-clocks = <0x03 0x1e>;
> + assigned-clock-rates = <0x989680>;
> + #pwm-cells = <0x02>;
> + status = "disabled";
> + phandle = <0x9a>;
> + };
> +
> + hvs at 7e400000 {
> + compatible = "brcm,bcm2835-hvs";
> + reg = <0x7e400000 0x6000>;
> + interrupts = <0x00 0x61 0x04>;
> + status = "disabled";
> + phandle = <0x9b>;
> + };
> +
> + dsi at 7e700000 {
> + compatible = "brcm,bcm2835-dsi1";
> + reg = <0x7e700000 0x8c>;
> + interrupts = <0x00 0x6c 0x04>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + #clock-cells = <0x01>;
> + clocks = <0x03 0x23 0x03 0x30 0x03 0x32>;
> + clock-names = "phy\0escape\0pixel";
> + clock-output-names =
> "dsi1_byte\0dsi1_ddr2\0dsi1_ddr";
> + status = "disabled";
> + phandle = <0x06>;
> + };
> +
> + csi at 7e800000 {
> + compatible = "brcm,bcm2835-unicam";
> + reg = <0x7e800000 0x800 0x7e802000 0x04>;
> + interrupts = <0x00 0x66 0x04>;
> + clocks = <0x03 0x2d>;
> + clock-names = "lp";
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + #clock-cells = <0x01>;
> + status = "disabled";
> + power-domains = <0x13 0x0c>;
> + phandle = <0x9c>;
> + };
> +
> + csi at 7e801000 {
> + compatible = "brcm,bcm2835-unicam";
> + reg = <0x7e801000 0x800 0x7e802004 0x04>;
> + interrupts = <0x00 0x67 0x04>;
> + clocks = <0x03 0x2e>;
> + clock-names = "lp";
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + #clock-cells = <0x01>;
> + status = "disabled";
> + power-domains = <0x13 0x0d>;
> + phandle = <0x9d>;
> +
> + port {
> +
> + endpoint {
> + data-lanes = <0x01 0x02>;
> + };
> + };
> + };
> +
> + i2c at 7e804000 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e804000 0x1000>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x14>;
> + clock-frequency = <0x186a0>;
> + phandle = <0x24>;
> + };
> +
> + i2c at 7e805000 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e805000 0x1000>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + clock-frequency = <0x186a0>;
> + phandle = <0x15>;
> + };
> +
> + vec at 7e806000 {
> + compatible = "brcm,bcm2835-vec";
> + reg = <0x7e806000 0x1000>;
> + clocks = <0x03 0x18>;
> + interrupts = <0x00 0x7b 0x04>;
> + status = "disabled";
> + phandle = <0x9e>;
> + };
> +
> + pixelvalve at 7e807000 {
> + compatible = "brcm,bcm2835-pixelvalve2";
> + reg = <0x7e807000 0x100>;
> + interrupts = <0x00 0x6a 0x04>;
> + status = "disabled";
> + phandle = <0x9f>;
> + };
> +
> + hdmi at 7e902000 {
> + compatible = "brcm,bcm2835-hdmi";
> + reg = <0x7e902000 0x600 0x7e808000 0x100>;
> + interrupts = <0x00 0x68 0x04 0x00 0x69 0x04>;
> + ddc = <0x15>;
> + clocks = <0x03 0x10 0x03 0x19>;
> + clock-names = "pixel\0hdmi";
> + dmas = <0x0a 0x11>;
> + dma-names = "audio-rx";
> + status = "disabled";
> + power-domains = <0x13 0x05>;
> + phandle = <0xa0>;
> + };
> +
> + usb at 7e980000 {
> + compatible = "brcm,bcm2708-usb";
> + reg = <0x7e980000 0x10000 0x7e00b200 0x200>;
> + interrupts = <0x00 0x49 0x04 0x00 0x28 0x04>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + clocks = <0x16>;
> + clock-names = "otg";
> + phys = <0x17>;
> + phy-names = "usb2-phy";
> + interrupt-names = "usb\0soft";
> + power-domains = <0x13 0x06>;
> + phandle = <0xa1>;
> + };
> +
> + gpu {
> + compatible = "brcm,bcm2835-vc4";
> + status = "disabled";
> + phandle = <0xa2>;
> + };
> +
> + local_intc at 40000000 {
> + compatible = "brcm,bcm2836-l1-intc";
> + reg = <0x40000000 0x100>;
> + phandle = <0xa3>;
> + };
> +
> + gic400 at 40041000 {
> + interrupt-controller;
> + #interrupt-cells = <0x03>;
> + compatible = "arm,gic-400";
> + reg = <0x40041000 0x1000 0x40042000 0x2000
> 0x40046000 0x2000 0x40048000 0x2000>;
> + phandle = <0x01>;
> + };
> +
> + thermal at 7d5d2200 {
> + compatible = "brcm,avs-tmon-bcm2838";
> + reg = <0x7d5d2200 0x2c>;
> + interrupts = <0x00 0x89 0x04>;
> + interrupt-names = "tmon";
> + clocks = <0x03 0x1b>;
> + #thermal-sensor-cells = <0x00>;
> + status = "okay";
> + phandle = <0x02>;
> + };
> +
> + serial at 7e201400 {
> + compatible =
> "brcm,bcm2835-pl011\0arm,pl011\0arm,primecell";
> + reg = <0x7e201400 0x200>;
> + interrupts = <0x00 0x79 0x04>;
> + clocks = <0x03 0x13 0x03 0x14>;
> + clock-names = "uartclk\0apb_pclk";
> + arm,primecell-periphid = <0x241011>;
> + status = "disabled";
> + phandle = <0xa4>;
> + };
> +
> + serial at 7e201600 {
> + compatible =
> "brcm,bcm2835-pl011\0arm,pl011\0arm,primecell";
> + reg = <0x7e201600 0x200>;
> + interrupts = <0x00 0x79 0x04>;
> + clocks = <0x03 0x13 0x03 0x14>;
> + clock-names = "uartclk\0apb_pclk";
> + arm,primecell-periphid = <0x241011>;
> + status = "disabled";
> + phandle = <0xa5>;
> + };
> +
> + serial at 7e201800 {
> + compatible =
> "brcm,bcm2835-pl011\0arm,pl011\0arm,primecell";
> + reg = <0x7e201800 0x200>;
> + interrupts = <0x00 0x79 0x04>;
> + clocks = <0x03 0x13 0x03 0x14>;
> + clock-names = "uartclk\0apb_pclk";
> + arm,primecell-periphid = <0x241011>;
> + status = "disabled";
> + phandle = <0xa6>;
> + };
> +
> + serial at 7e201a00 {
> + compatible =
> "brcm,bcm2835-pl011\0arm,pl011\0arm,primecell";
> + reg = <0x7e201a00 0x200>;
> + interrupts = <0x00 0x79 0x04>;
> + clocks = <0x03 0x13 0x03 0x14>;
> + clock-names = "uartclk\0apb_pclk";
> + arm,primecell-periphid = <0x241011>;
> + status = "disabled";
> + phandle = <0xa7>;
> + };
> +
> + spi at 7e204600 {
> + compatible = "brcm,bcm2835-spi";
> + reg = <0x7e204600 0x200>;
> + interrupts = <0x00 0x76 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xa8>;
> + };
> +
> + spi at 7e204800 {
> + compatible = "brcm,bcm2835-spi";
> + reg = <0x7e204800 0x200>;
> + interrupts = <0x00 0x76 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xa9>;
> + };
> +
> + spi at 7e204a00 {
> + compatible = "brcm,bcm2835-spi";
> + reg = <0x7e204a00 0x200>;
> + interrupts = <0x00 0x76 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xaa>;
> + };
> +
> + spi at 7e204c00 {
> + compatible = "brcm,bcm2835-spi";
> + reg = <0x7e204c00 0x200>;
> + interrupts = <0x00 0x76 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xab>;
> + };
> +
> + i2c at 7e205600 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e205600 0x200>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xac>;
> + };
> +
> + i2c at 7e205800 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e205800 0x200>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xad>;
> + };
> +
> + i2c at 7e205a00 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e205a00 0x200>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xae>;
> + };
> +
> + i2c at 7e205c00 {
> + compatible = "brcm,bcm2835-i2c";
> + reg = <0x7e205c00 0x200>;
> + interrupts = <0x00 0x75 0x04>;
> + clocks = <0x03 0x14>;
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + status = "disabled";
> + phandle = <0xaf>;
> + };
> +
> + emmc2 at 7e340000 {
> + compatible = "brcm,bcm2711-emmc2";
> + status = "okay";
> + interrupts = <0x00 0x7e 0x04>;
> + clocks = <0x03 0x33>;
> + reg = <0x7e340000 0x100>;
> + broken-cd;
> + vqmmc-supply = <0x18>;
> + phandle = <0xb0>;
> + };
> +
> + mmc at 7e300000 {
> + compatible =
> "brcm,bcm2835-mmc\0brcm,bcm2835-sdhci";
> + reg = <0x7e300000 0x100>;
> + interrupts = <0x00 0x7e 0x04>;
> + clocks = <0x03 0x1c>;
> + dmas = <0x0a 0x0b>;
> + dma-names = "rx-tx";
> + brcm,overclock-50 = <0x00>;
> + status = "disabled";
> + phandle = <0x28>;
> + };
> +
> + mmcnr at 7e300000 {
> + compatible =
> "brcm,bcm2835-mmc\0brcm,bcm2835-sdhci";
> + reg = <0x7e300000 0x100>;
> + interrupts = <0x00 0x7e 0x04>;
> + clocks = <0x03 0x1c>;
> + dmas = <0x0a 0x0b>;
> + dma-names = "rx-tx";
> + brcm,overclock-50 = <0x00>;
> + non-removable;
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x19>;
> + bus-width = <0x04>;
> + phandle = <0x29>;
> + };
> +
> + firmwarekms at 7e600000 {
> + compatible = "raspberrypi,rpi-firmware-kms";
> + reg = <0x7e600000 0x100>;
> + interrupts = <0x00 0x70 0x04>;
> + brcm,firmware = <0x07>;
> + status = "disabled";
> + phandle = <0xb1>;
> + };
> +
> + smi at 7e600000 {
> + compatible = "brcm,bcm2835-smi";
> + reg = <0x7e600000 0x100>;
> + interrupts = <0x00 0x70 0x04>;
> + clocks = <0x03 0x2a>;
> + assigned-clocks = <0x03 0x2a>;
> + assigned-clock-rates = <0x7735940>;
> + dmas = <0x0a 0x04>;
> + dma-names = "rx-tx";
> + status = "disabled";
> + phandle = <0xb2>;
> + };
> +
> + axiperf {
> + compatible = "brcm,bcm2835-axiperf";
> + reg = <0x7e009800 0x100 0x7ee08000 0x100>;
> + firmware = <0x07>;
> + status = "disabled";
> + phandle = <0x2a>;
> + };
> +
> + gpiomem {
> + compatible = "brcm,bcm2835-gpiomem";
> + reg = <0x7e200000 0x1000>;
> + };
> +
> + firmware {
> + compatible =
> "raspberrypi,bcm2835-firmware\0simple-bus";
> + #address-cells = <0x00>;
> + #size-cells = <0x00>;
> + mboxes = <0x1a>;
> + phandle = <0x07>;
> +
> + expgpio {
> + compatible = "raspberrypi,firmware-gpio";
> + gpio-controller;
> + #gpio-cells = <0x02>;
> + status = "okay";
> + phandle = <0x2d>;
> + };
> + };
> +
> + power {
> + compatible = "raspberrypi,bcm2835-power";
> + firmware = <0x07>;
> + #power-domain-cells = <0x01>;
> + phandle = <0x13>;
> + };
> +
> + fb {
> + compatible = "brcm,bcm2708-fb";
> + firmware = <0x07>;
> + status = "okay";
> + phandle = <0xb3>;
> + };
> +
> + vcsm {
> + compatible = "raspberrypi,bcm2835-vcsm";
> + firmware = <0x07>;
> + status = "okay";
> + phandle = <0xb4>;
> + };
> +
> + audio {
> + compatible = "brcm,bcm2835-audio";
> + brcm,pwm-channels = <0x08>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <0x1b>;
> + phandle = <0x25>;
> + };
> +
> + sound {
> + status = "disabled";
> + phandle = <0xb5>;
> + };
> +
> + virtgpio {
> + compatible = "brcm,bcm2835-virtgpio";
> + gpio-controller;
> + #gpio-cells = <0x02>;
> + firmware = <0x07>;
> + status = "okay";
> + phandle = <0xb6>;
> + };
> + };
> +
> + clocks {
> + compatible = "simple-bus";
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> +
> + clock at 3 {
> + compatible = "fixed-clock";
> + reg = <0x03>;
> + #clock-cells = <0x00>;
> + clock-output-names = "osc";
> + clock-frequency = <0x337f980>;
> + phandle = <0x04>;
> + };
> +
> + clock at 4 {
> + compatible = "fixed-clock";
> + reg = <0x04>;
> + #clock-cells = <0x00>;
> + clock-output-names = "otg";
> + clock-frequency = <0x1c9c3800>;
> + phandle = <0x16>;
> + };
> + };
> +
> + phy {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0x00>;
> + phandle = <0x17>;
> + };
> +
> + arm-pmu {
> + compatible = "arm,cortex-a72-pmu\0arm,cortex-a53-pmu";
> + interrupts = <0x00 0x10 0x04 0x00 0x11 0x04 0x00 0x12 0x04
> 0x00 0x13 0x04>;
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <0x01 0x0d 0xf08 0x01 0x0e 0xf08 0x01 0x0b
> 0xf08 0x01 0x0a 0xf08>;
> + arm,cpu-registers-not-fw-configured;
> + always-on;
> + };
> +
> + cpus {
> + #address-cells = <0x01>;
> + #size-cells = <0x00>;
> + enable-method = "brcm,bcm2836-smp";
> + phandle = <0xb7>;
> +
> + cpu at 0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x00>;
> + enable-method = "spin-table";
> + cpu-release-addr = <0x00 0xd8>;
> + phandle = <0xb8>;
> + };
> +
> + cpu at 1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x01>;
> + enable-method = "spin-table";
> + cpu-release-addr = <0x00 0xe0>;
> + phandle = <0xb9>;
> + };
> +
> + cpu at 2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x02>;
> + enable-method = "spin-table";
> + cpu-release-addr = <0x00 0xe8>;
> + phandle = <0xba>;
> + };
> +
> + cpu at 3 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x03>;
> + enable-method = "spin-table";
> + cpu-release-addr = <0x00 0xf0>;
> + phandle = <0xbb>;
> + };
> + };
> +
> + v3dbus {
> + compatible = "simple-bus";
> + #address-cells = <0x01>;
> + #size-cells = <0x01>;
> + ranges = <0x7c500000 0x00 0xfc500000 0x3300000 0x40000000
> 0x00 0xff800000 0x800000>;
> + dma-ranges = <0x00 0x00 0x00 0x3c000000>;
> +
> + v3d at 7ec04000 {
> + compatible = "brcm,2711-v3d";
> + reg = <0x7ec00000 0x4000 0x7ec04000 0x4000>;
> + reg-names = "hub\0core0";
> + power-domains = <0x1c 0x01>;
> + resets = <0x1c 0x00>;
> + clocks = <0x03 0x15>;
> + interrupts = <0x00 0x4a 0x04>;
> + status = "okay";
> + phandle = <0xbc>;
> + };
> + };
> +
> + scb {
> + compatible = "simple-bus";
> + #address-cells = <0x02>;
> + #size-cells = <0x01>;
> + ranges = <0x00 0x7c000000 0x00 0xfc000000
> + 0x3800000 0x00 0x40000000 0x00
> + 0xff800000 0x800000 0x06 0x00
> + 0x06 0x00 0x40000000 0x00
> + 0x00 0x00 0x00 0xfc000000>;
> + dma-ranges = <0x00 0x00 0x00 0x00 0xfc000000>;
> + phandle = <0xbd>;
> +
> + pcie at 7d500000 {
> + reg = <0x00 0x7d500000 0x9310 0x00 0x7e00f300
> 0x20>;
> + msi-controller;
> + msi-parent = <0x1d>;
> + #address-cells = <0x03>;
> + #interrupt-cells = <0x01>;
> + #size-cells = <0x02>;
> + bus-range = <0x00 0x01>;
> + compatible =
> "brcm,bcm7211-pcie\0brcm,bcm7445-pcie\0brcm,pci-plat-dev";
> + max-link-speed = <0x02>;
> + tot-num-pcie = <0x01>;
> + linux,pci-domain = <0x00>;
> + interrupts = <0x00 0x94 0x04 0x00 0x94 0x04>;
> + interrupt-names = "pcie\0msi";
> + interrupt-map-mask = <0x00 0x00 0x00 0x07>;
> + interrupt-map = <0x00 0x00 0x00 0x01
> + 0x01 0x00 0x8f 0x04 0x00 0x00 0x00 0x02
> + 0x01 0x00 0x90 0x04 0x00 0x00 0x00 0x03
> + 0x01 0x00 0x91 0x04 0x00 0x00 0x00 0x04
> + 0x01 0x00 0x92 0x04>;
> + ranges = <0x2000000 0x00 0xf8000000 0x06 0x00 0x00
> 0x4000000>;
> + dma-ranges = <0x2000000 0x00 0x00 0x00 0x00 0x01
> 0x00>;
> + status = "okay";
> + phandle = <0x1d>;
> + };
> +
> + genet at 7d580000 {
> + compatible = "brcm,genet-v5";
> + reg = <0x00 0x7d580000 0x10000>;
> + status = "okay";
> + #address-cells = <0x01>;
> + #size-cells = <0x01>;
> + interrupts = <0x00 0x9d 0x04 0x00 0x9e 0x04>;
> + phy-handle = <0x1e>;
> + phy-mode = "rgmii";
> + phandle = <0xbe>;
> +
> + mdio at e14 {
> + #address-cells = <0x00>;
> + #size-cells = <0x01>;
> + compatible = "brcm,genet-mdio-v5";
> + reg = <0xe14 0x08>;
> + reg-names = "mdio";
> +
> + genet-phy at 0 {
> + compatible =
> "ethernet-phy-ieee802.3-c22";
> + max-speed = <0x3e8>;
> + reg = <0x01>;
> + phandle = <0x1e>;
> + };
> + };
> + };
> +
> + dma at 7e007b00 {
> + compatible = "brcm,bcm2838-dma";
> + reg = <0x00 0x7e007b00 0x400>;
> + interrupts = <0x00 0x59 0x04 0x00 0x5a 0x04 0x00
> 0x5b
> + 0x04 0x00 0x5c 0x04>;
> + interrupt-names = "dma11\0dma12\0dma13\0dma14";
> + #dma-cells = <0x01>;
> + brcm,dma-channel-mask = <0x7000>;
> + phandle = <0xbf>;
> + };
> +
> + xhci at 7e9c0000 {
> + compatible = "generic-xhci";
> + status = "disabled";
> + reg = <0x00 0x7e9c0000 0x100000>;
> + interrupts = <0x00 0xb0 0x04>;
> + phandle = <0xc0>;
> + };
> +
> + mailbox at 7e00b840 {
> + compatible = "brcm,bcm2838-vchiq";
> + reg = <0x00 0x7e00b840 0x3c>;
> + interrupts = <0x00 0x22 0x04>;
> + phandle = <0xc1>;
> + };
> +
> + hevc-decoder at 7eb00000 {
> + compatible = "raspberrypi,argon-hevc-decoder";
> + reg = <0x00 0x7eb00000 0x10000>;
> + status = "okay";
> + };
> +
> + argon-local-intc at 7eb10000 {
> + compatible = "raspberrypi,argon-local-intc";
> + reg = <0x00 0x7eb10000 0x1000>;
> + status = "okay";
> + interrupts = <0x00 0x62 0x04>;
> + };
> +
> + h264-decoder at 7eb20000 {
> + compatible = "raspberrypi,argon-h264-decoder";
> + reg = <0x00 0x7eb20000 0x10000>;
> + status = "okay";
> + };
> +
> + vp9-decoder at 7eb30000 {
> + compatible = "raspberrypi,argon-vp9-decoder";
> + reg = <0x00 0x7eb30000 0x10000>;
> + status = "okay";
> + };
> + };
> +
> + fixedregulator_5v0 {
> + compatible = "regulator-fixed";
> + regulator-name = "5v0";
> + regulator-min-microvolt = <0x4c4b40>;
> + regulator-max-microvolt = <0x4c4b40>;
> + regulator-always-on;
> + phandle = <0x2e>;
> + };
> +
> + fixedregulator_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "3v3";
> + regulator-min-microvolt = <0x325aa0>;
> + regulator-max-microvolt = <0x325aa0>;
> + regulator-always-on;
> + phandle = <0xc2>;
> + };
> +
> + __overrides__ {
> + cam0-pwdn-ctrl;
> + cam0-pwdn;
> + cam0-led-ctrl;
> + cam0-led;
> + cache_line_size;
> + uart0 = [00 00 00 1f 73 74 61 74 75 73 00];
> + uart1 = "\0\0\0 status";
> + i2s = "\0\0\0!status";
> + spi = "\0\0\0\"status";
> + i2c0 = "\0\0\0#status";
> + i2c1 = "\0\0\0$status";
> + i2c2_iknowwhatimdoing = [00 00 00 15 73 74 61 74 75 73 00];
> + i2c0_baudrate = "\0\0\0#clock-frequency:0";
> + i2c1_baudrate = "\0\0\0$clock-frequency:0";
> + i2c2_baudrate = [00 00 00 15 63 6c 6f 63
> + 6b 2d 66 72 65 71 75 65
> + 6e 63 79 3a 30 00];
> + audio = "\0\0\0%status";
> + watchdog = [00 00 00 1c 73 74 61 74 75 73 00];
> + random = "\0\0\0&status";
> + sd_overclock = "\0\0\0'brcm,overclock-50:0";
> + sd_force_pio = "\0\0\0'brcm,force-pio?";
> + sd_pio_limit = "\0\0\0'brcm,pio-limit:0";
> + sd_debug = "\0\0\0'brcm,debug";
> + sdio_overclock =
> "\0\0\0(brcm,overclock-50:0\0\0\0\0)brcm,overclock-50:0";
> + axiperf = "\0\0\0*status";
> + arm_freq;
> + act_led_gpio = "\0\0\0+gpios:4";
> + act_led_activelow = "\0\0\0+gpios:8";
> + act_led_trigger = "\0\0\0+linux,default-trigger";
> + pwr_led_gpio = "\0\0\0,gpios:4";
> + pwr_led_activelow = "\0\0\0,gpios:8";
> + pwr_led_trigger = "\0\0\0,linux,default-trigger";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00 0x00 0x00>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + phandle = <0xc3>;
> +
> + act {
> + label = "led0";
> + linux,default-trigger = "mmc0";
> + gpios = <0x0f 0x2a 0x00>;
> + phandle = <0x2b>;
> + };
> +
> + pwr {
> + label = "led1";
> + linux,default-trigger = "input";
> + gpios = <0x2d 0x02 0x00>;
> + phandle = <0x2c>;
> + };
> + };
> +
> + sd_io_1v8_reg {
> + status = "okay";
> + compatible = "regulator-gpio";
> + vin-supply = <0x2e>;
> + regulator-name = "vdd-sd-io";
> + regulator-min-microvolt = <0x1b7740>;
> + regulator-max-microvolt = <0x325aa0>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-settling-time-us = <0x1388>;
> + gpios = <0x2d 0x04 0x00>;
> + states = <0x1b7740 0x01 0x325aa0 0x00>;
> + phandle = <0x18>;
> + };
> +
> + __symbols__ {
> + cpu_thermal = "/thermal-zones/cpu-thermal";
> + soc = "/soc";
> + txp = "/soc/txp at 7e004000";
> + dma = "/soc/dma at 7e007000";
> + watchdog = "/soc/watchdog at 7e100000";
> + pm = "/soc/watchdog at 7e100000";
> + clocks = "/soc/cprman at 7e101000";
> + random = "/soc/rng at 7e104000";
> + rng = "/soc/rng at 7e104000";
> + mailbox = "/soc/mailbox at 7e00b880";
> + gpio = "/soc/gpio at 7e200000";
> + dpi_gpio0 = "/soc/gpio at 7e200000/dpi_gpio0";
> + emmc_gpio22 = "/soc/gpio at 7e200000/emmc_gpio22";
> + emmc_gpio34 = "/soc/gpio at 7e200000/emmc_gpio34";
> + emmc_gpio48 = "/soc/gpio at 7e200000/emmc_gpio48";
> + gpclk0_gpio4 = "/soc/gpio at 7e200000/gpclk0_gpio4";
> + gpclk1_gpio5 = "/soc/gpio at 7e200000/gpclk1_gpio5";
> + gpclk1_gpio42 = "/soc/gpio at 7e200000/gpclk1_gpio42";
> + gpclk1_gpio44 = "/soc/gpio at 7e200000/gpclk1_gpio44";
> + gpclk2_gpio6 = "/soc/gpio at 7e200000/gpclk2_gpio6";
> + gpclk2_gpio43 = "/soc/gpio at 7e200000/gpclk2_gpio43";
> + i2c0_gpio0 = "/soc/gpio at 7e200000/i2c0_gpio0";
> + i2c0_gpio28 = "/soc/gpio at 7e200000/i2c0_gpio28";
> + i2c0_gpio44 = "/soc/gpio at 7e200000/i2c0_gpio44";
> + i2c1_gpio2 = "/soc/gpio at 7e200000/i2c1_gpio2";
> + i2c1_gpio44 = "/soc/gpio at 7e200000/i2c1_gpio44";
> + jtag_gpio22 = "/soc/gpio at 7e200000/jtag_gpio22";
> + pcm_gpio18 = "/soc/gpio at 7e200000/pcm_gpio18";
> + pcm_gpio28 = "/soc/gpio at 7e200000/pcm_gpio28";
> + pwm0_gpio12 = "/soc/gpio at 7e200000/pwm0_gpio12";
> + pwm0_gpio18 = "/soc/gpio at 7e200000/pwm0_gpio18";
> + pwm0_gpio40 = "/soc/gpio at 7e200000/pwm0_gpio40";
> + pwm1_gpio13 = "/soc/gpio at 7e200000/pwm1_gpio13";
> + pwm1_gpio19 = "/soc/gpio at 7e200000/pwm1_gpio19";
> + pwm1_gpio41 = "/soc/gpio at 7e200000/pwm1_gpio41";
> + pwm1_gpio45 = "/soc/gpio at 7e200000/pwm1_gpio45";
> + sdhost_pins = "/soc/gpio at 7e200000/sdhost_gpio48";
> + sdhost_gpio48 = "/soc/gpio at 7e200000/sdhost_gpio48";
> + spi0_gpio7 = "/soc/gpio at 7e200000/spi0_gpio7";
> + spi0_gpio35 = "/soc/gpio at 7e200000/spi0_gpio35";
> + spi1_gpio16 = "/soc/gpio at 7e200000/spi1_gpio16";
> + spi2_gpio40 = "/soc/gpio at 7e200000/spi2_gpio40";
> + uart0_gpio14 = "/soc/gpio at 7e200000/uart0_gpio14";
> + uart0_ctsrts_gpio16 = "/soc/gpio at 7e200000
> /uart0_ctsrts_gpio16";
> + uart0_ctsrts_gpio30 = "/soc/gpio at 7e200000
> /uart0_ctsrts_gpio30";
> + uart0_gpio32 = "/soc/gpio at 7e200000/uart0_gpio32";
> + uart0_gpio36 = "/soc/gpio at 7e200000/uart0_gpio36";
> + uart0_ctsrts_gpio38 = "/soc/gpio at 7e200000
> /uart0_ctsrts_gpio38";
> + uart1_gpio14 = "/soc/gpio at 7e200000/uart1_gpio14";
> + uart1_ctsrts_gpio16 = "/soc/gpio at 7e200000
> /uart1_ctsrts_gpio16";
> + uart1_gpio32 = "/soc/gpio at 7e200000/uart1_gpio32";
> + uart1_ctsrts_gpio30 = "/soc/gpio at 7e200000
> /uart1_ctsrts_gpio30";
> + uart1_gpio40 = "/soc/gpio at 7e200000/uart1_gpio40";
> + uart1_ctsrts_gpio42 = "/soc/gpio at 7e200000
> /uart1_ctsrts_gpio42";
> + gpclk0_gpio49 = "/soc/gpio at 7e200000/gpclk0_gpio49";
> + gpclk1_gpio50 = "/soc/gpio at 7e200000/gpclk1_gpio50";
> + gpclk2_gpio51 = "/soc/gpio at 7e200000/gpclk2_gpio51";
> + i2c0_gpio46 = "/soc/gpio at 7e200000/i2c0_gpio46";
> + i2c1_gpio46 = "/soc/gpio at 7e200000/i2c1_gpio46";
> + i2c3_gpio2 = "/soc/gpio at 7e200000/i2c3_gpio2";
> + i2c3_gpio4 = "/soc/gpio at 7e200000/i2c3_gpio4";
> + i2c4_gpio6 = "/soc/gpio at 7e200000/i2c4_gpio6";
> + i2c4_gpio8 = "/soc/gpio at 7e200000/i2c4_gpio8";
> + i2c5_gpio10 = "/soc/gpio at 7e200000/i2c5_gpio10";
> + i2c5_gpio12 = "/soc/gpio at 7e200000/i2c5_gpio12";
> + i2c6_gpio0 = "/soc/gpio at 7e200000/i2c6_gpio0";
> + i2c6_gpio22 = "/soc/gpio at 7e200000/i2c6_gpio22";
> + i2c_slave_gpio8 = "/soc/gpio at 7e200000/i2c_slave_gpio8";
> + jtag_gpio48 = "/soc/gpio at 7e200000/jtag_gpio48";
> + mii_gpio28 = "/soc/gpio at 7e200000/mii_gpio28";
> + mii_gpio36 = "/soc/gpio at 7e200000/mii_gpio36";
> + pcm_gpio50 = "/soc/gpio at 7e200000/pcm_gpio50";
> + pwm0_gpio52 = "/soc/gpio at 7e200000/pwm0_gpio52";
> + pwm1_gpio53 = "/soc/gpio at 7e200000/pwm1_gpio53";
> + rgmii_gpio35 = "/soc/gpio at 7e200000/rgmii_gpio35";
> + rgmii_irq_gpio34 = "/soc/gpio at 7e200000/rgmii_irq_gpio34";
> + rgmii_irq_gpio39 = "/soc/gpio at 7e200000/rgmii_irq_gpio39";
> + rgmii_mdio_gpio28 = "/soc/gpio at 7e200000
> /rgmii_mdio_gpio28";
> + rgmii_mdio_gpio37 = "/soc/gpio at 7e200000
> /rgmii_mdio_gpio37";
> + spi0_gpio46 = "/soc/gpio at 7e200000/spi0_gpio46";
> + spi2_gpio46 = "/soc/gpio at 7e200000/spi2_gpio46";
> + spi3_gpio0 = "/soc/gpio at 7e200000/spi3_gpio0";
> + spi4_gpio4 = "/soc/gpio at 7e200000/spi4_gpio4";
> + spi5_gpio12 = "/soc/gpio at 7e200000/spi5_gpio12";
> + spi6_gpio18 = "/soc/gpio at 7e200000/spi6_gpio18";
> + uart2_gpio0 = "/soc/gpio at 7e200000/uart2_gpio0";
> + uart2_ctsrts_gpio2 = "/soc/gpio at 7e200000
> /uart2_ctsrts_gpio2";
> + uart3_gpio4 = "/soc/gpio at 7e200000/uart3_gpio4";
> + uart3_ctsrts_gpio6 = "/soc/gpio at 7e200000
> /uart3_ctsrts_gpio6";
> + uart4_gpio8 = "/soc/gpio at 7e200000/uart4_gpio8";
> + uart4_ctsrts_gpio10 = "/soc/gpio at 7e200000
> /uart4_ctsrts_gpio10";
> + uart5_gpio12 = "/soc/gpio at 7e200000/uart5_gpio12";
> + uart5_ctsrts_gpio14 = "/soc/gpio at 7e200000
> /uart5_ctsrts_gpio14";
> + dpi_18bit_gpio0 = "/soc/gpio at 7e200000/dpi_18bit_gpio0";
> + spi0_pins = "/soc/gpio at 7e200000/spi0_pins";
> + spi0_cs_pins = "/soc/gpio at 7e200000/spi0_cs_pins";
> + spi3_pins = "/soc/gpio at 7e200000/spi3_pins";
> + spi3_cs_pins = "/soc/gpio at 7e200000/spi3_cs_pins";
> + spi4_pins = "/soc/gpio at 7e200000/spi4_pins";
> + spi4_cs_pins = "/soc/gpio at 7e200000/spi4_cs_pins";
> + spi5_pins = "/soc/gpio at 7e200000/spi5_pins";
> + spi5_cs_pins = "/soc/gpio at 7e200000/spi5_cs_pins";
> + spi6_pins = "/soc/gpio at 7e200000/spi6_pins";
> + spi6_cs_pins = "/soc/gpio at 7e200000/spi6_cs_pins";
> + i2c0_pins = "/soc/gpio at 7e200000/i2c0";
> + i2c1_pins = "/soc/gpio at 7e200000/i2c1";
> + i2c3_pins = "/soc/gpio at 7e200000/i2c3";
> + i2c4_pins = "/soc/gpio at 7e200000/i2c4";
> + i2c5_pins = "/soc/gpio at 7e200000/i2c5";
> + i2c6_pins = "/soc/gpio at 7e200000/i2c6";
> + i2s_pins = "/soc/gpio at 7e200000/i2s";
> + sdio_pins = "/soc/gpio at 7e200000/sdio_pins";
> + bt_pins = "/soc/gpio at 7e200000/bt_pins";
> + uart0_pins = "/soc/gpio at 7e200000/uart0_pins";
> + uart1_pins = "/soc/gpio at 7e200000/uart1_pins";
> + uart2_pins = "/soc/gpio at 7e200000/uart2_pins";
> + uart3_pins = "/soc/gpio at 7e200000/uart3_pins";
> + uart4_pins = "/soc/gpio at 7e200000/uart4_pins";
> + uart5_pins = "/soc/gpio at 7e200000/uart5_pins";
> + audio_pins = "/soc/gpio at 7e200000/audio_pins";
> + uart0 = "/soc/serial at 7e201000";
> + sdhost = "/soc/mmc at 7e202000";
> + i2s = "/soc/i2s at 7e203000";
> + spi0 = "/soc/spi at 7e204000";
> + spi = "/soc/spi at 7e204000";
> + spidev0 = "/soc/spi at 7e204000/spidev at 0";
> + spidev1 = "/soc/spi at 7e204000/spidev at 1";
> + i2c0 = "/soc/i2c at 7e205000";
> + pixelvalve0 = "/soc/pixelvalve at 7e206000";
> + pixelvalve1 = "/soc/pixelvalve at 7e207000";
> + dpi = "/soc/dpi at 7e208000";
> + dsi0 = "/soc/dsi at 7e209000";
> + aux = "/soc/aux at 7e215000";
> + uart1 = "/soc/serial at 7e215040";
> + spi1 = "/soc/spi at 7e215080";
> + spi2 = "/soc/spi at 7e2150c0";
> + pwm = "/soc/pwm at 7e20c000";
> + hvs = "/soc/hvs at 7e400000";
> + dsi1 = "/soc/dsi at 7e700000";
> + csi0 = "/soc/csi at 7e800000";
> + csi1 = "/soc/csi at 7e801000";
> + i2c1 = "/soc/i2c at 7e804000";
> + i2c2 = "/soc/i2c at 7e805000";
> + vec = "/soc/vec at 7e806000";
> + pixelvalve2 = "/soc/pixelvalve at 7e807000";
> + hdmi = "/soc/hdmi at 7e902000";
> + usb = "/soc/usb at 7e980000";
> + vc4 = "/soc/gpu";
> + local_intc = "/soc/local_intc at 40000000";
> + gicv2 = "/soc/gic400 at 40041000";
> + thermal = "/soc/thermal at 7d5d2200";
> + uart2 = "/soc/serial at 7e201400";
> + uart3 = "/soc/serial at 7e201600";
> + uart4 = "/soc/serial at 7e201800";
> + uart5 = "/soc/serial at 7e201a00";
> + spi3 = "/soc/spi at 7e204600";
> + spi4 = "/soc/spi at 7e204800";
> + spi5 = "/soc/spi at 7e204a00";
> + spi6 = "/soc/spi at 7e204c00";
> + i2c3 = "/soc/i2c at 7e205600";
> + i2c4 = "/soc/i2c at 7e205800";
> + i2c5 = "/soc/i2c at 7e205a00";
> + i2c6 = "/soc/i2c at 7e205c00";
> + emmc2 = "/soc/emmc2 at 7e340000";
> + mmc = "/soc/mmc at 7e300000";
> + mmcnr = "/soc/mmcnr at 7e300000";
> + firmwarekms = "/soc/firmwarekms at 7e600000";
> + smi = "/soc/smi at 7e600000";
> + axiperf = "/soc/axiperf";
> + firmware = "/soc/firmware";
> + expgpio = "/soc/firmware/expgpio";
> + power = "/soc/power";
> + fb = "/soc/fb";
> + vcsm = "/soc/vcsm";
> + audio = "/soc/audio";
> + sound = "/soc/sound";
> + virtgpio = "/soc/virtgpio";
> + clk_osc = "/clocks/clock at 3";
> + clk_usb = "/clocks/clock at 4";
> + usbphy = "/phy";
> + cpus = "/cpus";
> + cpu0 = "/cpus/cpu at 0";
> + cpu1 = "/cpus/cpu at 1";
> + cpu2 = "/cpus/cpu at 2";
> + cpu3 = "/cpus/cpu at 3";
> + v3d = "/v3dbus/v3d at 7ec04000";
> + scb = "/scb";
> + pcie_0 = "/scb/pcie at 7d500000";
> + genet = "/scb/genet at 7d580000";
> + phy1 = "/scb/genet at 7d580000/mdio at e14/genet-phy at 0";
> + dma40 = "/scb/dma at 7e007b00";
> + xhci = "/scb/xhci at 7e9c0000";
> + vchiq = "/scb/mailbox at 7e00b840";
> + vdd_5v0_reg = "/fixedregulator_5v0";
> + vdd_3v3_reg = "/fixedregulator_3v3";
> + leds = "/leds";
> + act_led = "/leds/act";
> + pwr_led = "/leds/pwr";
> + sd_io_1v8_reg = "/sd_io_1v8_reg";
> + };
> +};
> diff --git a/configs/rpi_4_32b_defconfig b/configs/rpi_4_32b_defconfig
> index d592df50706..31d77dbe4eb 100644
> --- a/configs/rpi_4_32b_defconfig
> +++ b/configs/rpi_4_32b_defconfig
> @@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00008000
> CONFIG_TARGET_RPI_4_32B=y
> CONFIG_SYS_MALLOC_F_LEN=0x2000
> CONFIG_ENV_SIZE=0x4000
> +CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b"
> CONFIG_DISTRO_DEFAULTS=y
> CONFIG_SYS_LOAD_ADDR=0x1000000
> CONFIG_OF_BOARD_SETUP=y
> diff --git a/configs/rpi_4_defconfig b/configs/rpi_4_defconfig
> index ab5cc90d912..a2a88d66dbd 100644
> --- a/configs/rpi_4_defconfig
> +++ b/configs/rpi_4_defconfig
> @@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00080000
> CONFIG_TARGET_RPI_4=y
> CONFIG_SYS_MALLOC_F_LEN=0x2000
> CONFIG_ENV_SIZE=0x4000
> +CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b"
> CONFIG_DISTRO_DEFAULTS=y
> CONFIG_SYS_LOAD_ADDR=0x1000000
> CONFIG_OF_BOARD_SETUP=y
> diff --git a/configs/rpi_arm64_defconfig b/configs/rpi_arm64_defconfig
> index 382d99dc2eb..fb8abbccc45 100644
> --- a/configs/rpi_arm64_defconfig
> +++ b/configs/rpi_arm64_defconfig
> @@ -6,6 +6,7 @@ CONFIG_S
--
François-Frédéric Ozog | *Director Business Development*
T: +33.67221.6485
francois.ozog at linaro.org | Skype: ffozog
More information about the U-Boot
mailing list