[PATCH] distro_boot: Fix bootfile env after calling boot_extlinux

[Art Nikpal]

Yes changes inside include/config_distro_bootcmd.h not the best solution
for this issue.
I think it is better to change sysboot cmd and i have prepared another
solution already!
https://patchwork.ozlabs.org/project/uboot/patch/20211013033912.3297227-1-art@khadas.com/
how about this ?

On Wed, Oct 13, 2021 at 5:07 AM Tom Rini <trini at konsulko.com> wrote:

> On Tue, Oct 12, 2021 at 02:31:18PM -0600, Simon Glass wrote:
> > Hi Tom,
> >
> > On Tue, 12 Oct 2021 at 13:44, Tom Rini <trini at konsulko.com> wrote:
> > >
> > > On Tue, Oct 12, 2021 at 04:55:44PM +0800, Artem Lapkin wrote:
> > >
> > > > Problem
> > > >
> > > > PXE cannot boot normally after Sysboot changed the bootfile env
> (called
> > > > from boot_extlinux) from the default "boot.scr.uimg" to
> > > > "/boot/extlinux/extlinux.conf".
> > > >
> > > > In addition, an unbootable extlinux configuration will also make the
> PXE
> > > > boot unbootable, because it will use the incorrect path
> "/boot/extlinux/"
> > > > from the bootfile env.
> > > >
> > > > Solution
> > > >
> > > > Save and restore default bootfile env value when boot_extlinux is
> used.
> > > >
> > > > Example
> > > > ================================================================
> > > > Hit SPACE in 2 seconds to stop autoboot
> > > > ... is now current device
> > > > Found /boot/extlinux/extlinux.conf
> > > > Retrieving file: /boot/extlinux/extlinux.conf
> > > > 413 bytes read in 2 ms (201.2 KiB/s)
> > > > Skipping Krescue for failure retrieving kernel
> > > > SCRIPT FAILED: continuing...
> > > > ...
> > > > Speed: 1000, full duplex
> > > > BOOTP broadcast 1
> > > > DHCP client bound to address 192.168.11.151 (8 ms)
> > > > Using ethernet at ff3f0000 device
> > > > TFTP from server 192.168.11.1; our IP address is 192.168.11.151
> > > > Filename '/boot/extlinux/pxelinux.cfg/default'.
> > > > Not retrying...
> > > > ================================================================
> > > >
> > > > Signed-off-by: Artem Lapkin <art at khadas.com>
> > > > ---
> > > >  include/config_distro_bootcmd.h | 2 ++
> > > >  1 file changed, 2 insertions(+)
> > > >
> > > > diff --git a/include/config_distro_bootcmd.h
> b/include/config_distro_bootcmd.h
> > > > index 3f724aa10f..db3d1b2362 100644
> > > > --- a/include/config_distro_bootcmd.h
> > > > +++ b/include/config_distro_bootcmd.h
> > > > @@ -445,7 +445,9 @@
> > > >                               "${devnum}:${distro_bootpart} "
>    \
> > > >                               "${prefix}${boot_syslinux_conf}; then
> "   \
> > > >                       "echo Found ${prefix}${boot_syslinux_conf}; "
>    \
> > > > +                     "bootfile_bak=${bootfile}; "
>     \
> > > >                       "run boot_extlinux; "
>    \
> > > > +                     "setenv bootfile ${bootfile_bak}; "
>    \
> > > >                       "echo SCRIPT FAILED: continuing...; "
>    \
> > > >               "fi\0"
>     \
> > > >       \
> > >
> > > We've had this kind of problem before, and the answer is that variables
> > > should be local, not global in scope.  In this case, I see that the way
> > > the pxe/sysboot code works is that we have to env_set("..") in one
> place
> > > to env_get("..") in another, so I don't see a way around this.
> > >
> > > Reviewed-by: Tom Rini <trini at konsulko.com>
> >
> > IMO a better approach will be the bootflow implementation. I hope to
> > get v2 out early next week.
>
> I'm not sure if the bootflow way of going here would or would not have
> the same problem, or perhaps a slightly different problem.  At heart
> here, "sysboot" calls env_set(...) and then calls in to the pxe code
> which does env_get(...).  So now I wonder how this would be fixed in
> bootflow, since we aren't dealing with the environment directly.
>
> --
> Tom
>