[PATCH v4 3/4] pwm: Add driver for cadence TTC
Michal Simek
michal.simek at xilinx.com
Fri Oct 15 15:17:29 CEST 2021
TTC has three modes of operations. Timer, PWM and input counters.
There is already driver for timer under CADENCE_TTC_TIMER which is used for
ZynqMP R5 configuration.
This driver is targeting PWM which is for example configuration which can
be used for fan control.
The driver has been tested on Xilinx Kria SOM platform where fan is
connected to one PL pin. When TTC output is connected via EMIO to PL pin
TTC pwm can be configured and tested for example like this:
pwm config 0 0 10000 1200
pwm enable 0 0
pwm config 0 0 10000 1400
pwm config 0 0 10000 1600
Signed-off-by: Michal Simek <michal.simek at xilinx.com>
Reviewed-by: Sean Anderson <sean.anderson at seco.com>
---
Changes in v4:
- - Add reviewed-by tag
Changes in v3:
- Add bind function to check pwm-cells to recognize PWM driver
- Use timer-width in prescaler calculation
- Record timer width in platdata instead of timer mask
- Also disable wave out in config function
Changes in v2:
- Detect pwm-cells property for PWM driver
- Fix all macro names
- Use BIT and GENMASK macros
- Introduce TTC_REG macro for reg offsets
- Use FIELD_PREP
- Move cadence_ttc_pwm_of_to_plat() below probe
- Introduce struct cadence_ttc_pwm_plat
- Read timer-width from DT
- Use NSEC_PER_SEC macro
- Use clock_ctrl variable instead of x - all reported by Sean
MAINTAINERS | 1 +
drivers/pwm/Kconfig | 7 +
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-cadence-ttc.c | 261 ++++++++++++++++++++++++++++++++++
4 files changed, 270 insertions(+)
create mode 100644 drivers/pwm/pwm-cadence-ttc.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 71f468c00a8f..d8873e520c8f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -599,6 +599,7 @@ F: drivers/mmc/zynq_sdhci.c
F: drivers/mtd/nand/raw/zynq_nand.c
F: drivers/net/phy/xilinx_phy.c
F: drivers/net/zynq_gem.c
+F: drivers/pwm/pwm-cadence-ttc.c
F: drivers/serial/serial_zynq.c
F: drivers/reset/reset-zynqmp.c
F: drivers/rtc/zynqmp_rtc.c
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 669d3fa4fc59..ec205ae4fa8a 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -15,6 +15,13 @@ config PWM_AT91
help
Support for PWM hardware on AT91 based SoC.
+config PWM_CADENCE_TTC
+ bool "Enable support for the Cadence TTC PWM"
+ depends on DM_PWM && !CADENCE_TTC_TIMER
+ help
+ Cadence TTC can be configured as timer which is done via
+ CONFIG_CADENCE_TTC_TIMER or as PWM. This is covering only PWM now.
+
config PWM_CROS_EC
bool "Enable support for the Chrome OS EC PWM"
depends on DM_PWM
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 55f2bc081d25..54413c689cac 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -11,6 +11,7 @@
obj-$(CONFIG_DM_PWM) += pwm-uclass.o
obj-$(CONFIG_PWM_AT91) += pwm-at91.o
+obj-$(CONFIG_PWM_CADENCE_TTC) += pwm-cadence-ttc.o
obj-$(CONFIG_PWM_CROS_EC) += cros_ec_pwm.o
obj-$(CONFIG_PWM_EXYNOS) += exynos_pwm.o
obj-$(CONFIG_PWM_IMX) += pwm-imx.o pwm-imx-util.o
diff --git a/drivers/pwm/pwm-cadence-ttc.c b/drivers/pwm/pwm-cadence-ttc.c
new file mode 100644
index 000000000000..dc3b314b0cce
--- /dev/null
+++ b/drivers/pwm/pwm-cadence-ttc.c
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * (C) Copyright 2021 Xilinx, Inc. Michal Simek
+ */
+
+#define LOG_CATEGORY UCLASS_PWM
+
+#include <clk.h>
+#include <common.h>
+#include <div64.h>
+#include <dm.h>
+#include <log.h>
+#include <pwm.h>
+#include <asm/io.h>
+#include <log.h>
+#include <div64.h>
+#include <linux/bitfield.h>
+#include <linux/math64.h>
+#include <linux/log2.h>
+#include <dm/device_compat.h>
+
+#define CLOCK_CONTROL 0
+#define COUNTER_CONTROL 0xc
+#define INTERVAL_COUNTER 0x24
+#define MATCH_1_COUNTER 0x30
+
+#define CLK_FALLING_EDGE BIT(6)
+#define CLK_SRC_EXTERNAL BIT(5)
+#define CLK_PRESCALE_MASK GENMASK(4, 1)
+#define CLK_PRESCALE_ENABLE BIT(0)
+
+#define COUNTER_WAVE_POL BIT(6)
+#define COUNTER_WAVE_DISABLE BIT(5)
+#define COUNTER_RESET BIT(4)
+#define COUNTER_MATCH_ENABLE BIT(3)
+#define COUNTER_DECREMENT_ENABLE BIT(2)
+#define COUNTER_INTERVAL_ENABLE BIT(1)
+#define COUNTER_COUNTING_DISABLE BIT(0)
+
+#define NSEC_PER_SEC 1000000000L
+
+#define TTC_REG(reg, channel) ((reg) + (channel) * sizeof(u32))
+#define TTC_CLOCK_CONTROL(reg, channel) \
+ TTC_REG((reg) + CLOCK_CONTROL, (channel))
+#define TTC_COUNTER_CONTROL(reg, channel) \
+ TTC_REG((reg) + COUNTER_CONTROL, (channel))
+#define TTC_INTERVAL_COUNTER(reg, channel) \
+ TTC_REG((reg) + INTERVAL_COUNTER, (channel))
+#define TTC_MATCH_1_COUNTER(reg, channel) \
+ TTC_REG((reg) + MATCH_1_COUNTER, (channel))
+
+struct cadence_ttc_pwm_plat {
+ u8 *regs;
+ u32 timer_width;
+};
+
+struct cadence_ttc_pwm_priv {
+ u8 *regs;
+ u32 timer_width;
+ u32 timer_mask;
+ unsigned long frequency;
+ bool invert[2];
+};
+
+static int cadence_ttc_pwm_set_invert(struct udevice *dev, uint channel,
+ bool polarity)
+{
+ struct cadence_ttc_pwm_priv *priv = dev_get_priv(dev);
+
+ if (channel > 2) {
+ dev_err(dev, "Unsupported channel number %d(max 2)\n", channel);
+ return -EINVAL;
+ }
+
+ priv->invert[channel] = polarity;
+
+ dev_dbg(dev, "polarity=%u. Please config PWM again\n", polarity);
+
+ return 0;
+}
+
+static int cadence_ttc_pwm_set_config(struct udevice *dev, uint channel,
+ uint period_ns, uint duty_ns)
+{
+ struct cadence_ttc_pwm_priv *priv = dev_get_priv(dev);
+ u32 counter_ctrl, clock_ctrl;
+ int period_clocks, duty_clocks, prescaler;
+
+ dev_dbg(dev, "channel %d, duty %d/period %d ns\n", channel,
+ duty_ns, period_ns);
+
+ if (channel > 2) {
+ dev_err(dev, "Unsupported channel number %d(max 2)\n", channel);
+ return -EINVAL;
+ }
+
+ /* Make sure counter is stopped */
+ counter_ctrl = readl(TTC_COUNTER_CONTROL(priv->regs, channel));
+ setbits_le32(TTC_COUNTER_CONTROL(priv->regs, channel),
+ COUNTER_COUNTING_DISABLE | COUNTER_WAVE_DISABLE);
+
+ /* Calculate period, prescaler and set clock control register */
+ period_clocks = div64_u64(((int64_t)period_ns * priv->frequency),
+ NSEC_PER_SEC);
+
+ prescaler = ilog2(period_clocks) + 1 - priv->timer_width;
+ if (prescaler < 0)
+ prescaler = 0;
+
+ clock_ctrl = readl(TTC_CLOCK_CONTROL(priv->regs, channel));
+
+ if (!prescaler) {
+ clock_ctrl &= ~(CLK_PRESCALE_ENABLE | CLK_PRESCALE_MASK);
+ } else {
+ clock_ctrl &= ~CLK_PRESCALE_MASK;
+ clock_ctrl |= CLK_PRESCALE_ENABLE;
+ clock_ctrl |= FIELD_PREP(CLK_PRESCALE_MASK, prescaler - 1);
+ };
+
+ /* External source is not handled by this driver now */
+ clock_ctrl &= ~CLK_SRC_EXTERNAL;
+
+ writel(clock_ctrl, TTC_CLOCK_CONTROL(priv->regs, channel));
+
+ /* Calculate interval and set counter control value */
+ duty_clocks = div64_u64(((int64_t)duty_ns * priv->frequency),
+ NSEC_PER_SEC);
+
+ writel((period_clocks >> prescaler) & priv->timer_mask,
+ TTC_INTERVAL_COUNTER(priv->regs, channel));
+ writel((duty_clocks >> prescaler) & priv->timer_mask,
+ TTC_MATCH_1_COUNTER(priv->regs, channel));
+
+ /* Restore/reset counter */
+ counter_ctrl &= ~COUNTER_DECREMENT_ENABLE;
+ counter_ctrl |= COUNTER_INTERVAL_ENABLE |
+ COUNTER_RESET |
+ COUNTER_MATCH_ENABLE;
+
+ if (priv->invert[channel])
+ counter_ctrl |= COUNTER_WAVE_POL;
+ else
+ counter_ctrl &= ~COUNTER_WAVE_POL;
+
+ writel(counter_ctrl, TTC_COUNTER_CONTROL(priv->regs, channel));
+
+ dev_dbg(dev, "%d/%d clocks, prescaler 2^%d\n", duty_clocks,
+ period_clocks, prescaler);
+
+ return 0;
+};
+
+static int cadence_ttc_pwm_set_enable(struct udevice *dev, uint channel,
+ bool enable)
+{
+ struct cadence_ttc_pwm_priv *priv = dev_get_priv(dev);
+
+ if (channel > 2) {
+ dev_err(dev, "Unsupported channel number %d(max 2)\n", channel);
+ return -EINVAL;
+ }
+
+ dev_dbg(dev, "Enable: %d, channel %d\n", enable, channel);
+
+ if (enable) {
+ clrbits_le32(TTC_COUNTER_CONTROL(priv->regs, channel),
+ COUNTER_COUNTING_DISABLE |
+ COUNTER_WAVE_DISABLE);
+ setbits_le32(TTC_COUNTER_CONTROL(priv->regs, channel),
+ COUNTER_RESET);
+ } else {
+ setbits_le32(TTC_COUNTER_CONTROL(priv->regs, channel),
+ COUNTER_COUNTING_DISABLE |
+ COUNTER_WAVE_DISABLE);
+ }
+
+ return 0;
+};
+
+static int cadence_ttc_pwm_probe(struct udevice *dev)
+{
+ struct cadence_ttc_pwm_priv *priv = dev_get_priv(dev);
+ struct cadence_ttc_pwm_plat *plat = dev_get_plat(dev);
+ struct clk clk;
+ int ret;
+
+ priv->regs = plat->regs;
+ priv->timer_width = plat->timer_width;
+ priv->timer_mask = GENMASK(priv->timer_width - 1, 0);
+
+ ret = clk_get_by_index(dev, 0, &clk);
+ if (ret < 0) {
+ dev_err(dev, "failed to get clock\n");
+ return ret;
+ }
+
+ priv->frequency = clk_get_rate(&clk);
+ if (IS_ERR_VALUE(priv->frequency)) {
+ dev_err(dev, "failed to get rate\n");
+ return priv->frequency;
+ }
+ dev_dbg(dev, "Clk frequency: %ld\n", priv->frequency);
+
+ ret = clk_enable(&clk);
+ if (ret) {
+ dev_err(dev, "failed to enable clock\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int cadence_ttc_pwm_of_to_plat(struct udevice *dev)
+{
+ struct cadence_ttc_pwm_plat *plat = dev_get_plat(dev);
+ const char *cells;
+
+ cells = dev_read_prop(dev, "#pwm-cells", NULL);
+ if (!cells)
+ return -EINVAL;
+
+ plat->regs = dev_read_addr_ptr(dev);
+
+ plat->timer_width = dev_read_u32_default(dev, "timer-width", 16);
+
+ return 0;
+}
+
+static int cadence_ttc_pwm_bind(struct udevice *dev)
+{
+ const char *cells;
+
+ cells = dev_read_prop(dev, "#pwm-cells", NULL);
+ if (!cells)
+ return -ENODEV;
+
+ return 0;
+}
+
+static const struct pwm_ops cadence_ttc_pwm_ops = {
+ .set_invert = cadence_ttc_pwm_set_invert,
+ .set_config = cadence_ttc_pwm_set_config,
+ .set_enable = cadence_ttc_pwm_set_enable,
+};
+
+static const struct udevice_id cadence_ttc_pwm_ids[] = {
+ { .compatible = "cdns,ttc" },
+ { }
+};
+
+U_BOOT_DRIVER(cadence_ttc_pwm) = {
+ .name = "cadence_ttc_pwm",
+ .id = UCLASS_PWM,
+ .of_match = cadence_ttc_pwm_ids,
+ .ops = &cadence_ttc_pwm_ops,
+ .bind = cadence_ttc_pwm_bind,
+ .of_to_plat = cadence_ttc_pwm_of_to_plat,
+ .probe = cadence_ttc_pwm_probe,
+ .priv_auto = sizeof(struct cadence_ttc_pwm_priv),
+ .plat_auto = sizeof(struct cadence_ttc_pwm_plat),
+};
--
2.33.1
More information about the U-Boot
mailing list