[PATCH v3] driver: spi: add bcm iproc qspi support.
Roman Bacik
roman.bacik at broadcom.com
Mon Oct 25 18:48:56 CEST 2021
> -----Original Message-----
> From: Jagan Teki <jagan at amarulasolutions.com>
> Sent: Sunday, October 24, 2021 11:44 PM
> To: Roman Bacik <roman.bacik at broadcom.com>
> Cc: U-Boot Mailing List <u-boot at lists.denx.de>; Rayagonda Kokatanur
> <rayagonda.kokatanur at broadcom.com>; Bharat Gooty
> <bharat.gooty at broadcom.com>
> Subject: Re: [PATCH v3] driver: spi: add bcm iproc qspi support.
>
> On Thu, Oct 21, 2021 at 4:01 AM Roman Bacik
> <roman.bacik at broadcom.com> wrote:
> >
> > From: Rayagonda Kokatanur <rayagonda.kokatanur at broadcom.com>
> >
> > IPROC qspi driver supports both BSPI and MSPI modes.
> >
> > Signed-off-by: Rayagonda Kokatanur
> <rayagonda.kokatanur at broadcom.com>
> > Signed-off-by: Bharat Gooty <bharat.gooty at broadcom.com>
> > Acked-by: Rayagonda Kokatanur <rayagonda.kokatanur at broadcom.com>
> >
> > Signed-off-by: Roman Bacik <roman.bacik at broadcom.com>
> > ---
> >
> > Changes in v3:
> > - fix warning by including linux/delay.h
> > - change ofdata_to_platdata to of_to_plat
> > - change priv_auto_alloc_size to priv_auto
> >
> > Changes in v2:
> > - remove include spi-nor.h
> > - define and use named BITs for writing register values
> > - remove bspi_set_4byte_mode() method
> >
> > drivers/spi/Kconfig | 6 +
> > drivers/spi/Makefile | 1 +
> > drivers/spi/iproc_qspi.c | 713
> +++++++++++++++++++++++++++++++++++++++
> > drivers/spi/iproc_qspi.h | 20 ++
> > 4 files changed, 740 insertions(+)
> > create mode 100644 drivers/spi/iproc_qspi.c
> > create mode 100644 drivers/spi/iproc_qspi.h
> >
> > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> > index d07e9a28af82..e76fadef32dd 100644
> > --- a/drivers/spi/Kconfig
> > +++ b/drivers/spi/Kconfig
> > @@ -178,6 +178,12 @@ config ICH_SPI
> > access the SPI NOR flash on platforms embedding this Intel
> > ICH IP core.
> >
> > +config IPROC_QSPI
> > + bool "QSPI driver for BCM iProc QSPI Controller"
> > + help
> > + This selects the BCM iProc QSPI controller.
> > + This driver support spi flash single, quad and memory reads.
> > +
> > config KIRKWOOD_SPI
> > bool "Marvell Kirkwood SPI Driver"
> > help
> > diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> > index d2f24bccefd3..869763187062 100644
> > --- a/drivers/spi/Makefile
> > +++ b/drivers/spi/Makefile
> > @@ -33,6 +33,7 @@ obj-$(CONFIG_FSL_DSPI) += fsl_dspi.o
> > obj-$(CONFIG_FSL_ESPI) += fsl_espi.o
> > obj-$(CONFIG_SYNQUACER_SPI) += spi-synquacer.o
> > obj-$(CONFIG_ICH_SPI) += ich.o
> > +obj-$(CONFIG_IPROC_QSPI) += iproc_qspi.o
> > obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
> > obj-$(CONFIG_MESON_SPIFC) += meson_spifc.o
> > obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
> > diff --git a/drivers/spi/iproc_qspi.c b/drivers/spi/iproc_qspi.c
> > new file mode 100644
> > index 000000000000..08881bf61764
> > --- /dev/null
> > +++ b/drivers/spi/iproc_qspi.c
> > @@ -0,0 +1,713 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2020-2021 Broadcom
> > + */
> > +
> > +#include <common.h>
> > +#include <dm.h>
> > +#include <errno.h>
> > +#include <malloc.h>
> > +#include <spi.h>
> > +#include <asm/io.h>
> > +#include <linux/delay.h>
> > +#include <linux/err.h>
> > +#include "iproc_qspi.h"
> > +
> > +/* 175MHz */
> > +#define QSPI_AXI_CLK 175000000
> > +#define QSPI_DEF_SCK_FREQ 50000000
> > +#define QSPI_WAIT_TIMEOUT_MS 200U
> > +#define DWORD_ALIGNED(a) (!(((ulong)(a)) & 3))
> > +
> > +/* Chip attributes */
> > +#define SPBR_MIN 8U
> > +#define SPBR_MAX 255U
> > +#define NUM_CDRAM 16U
> > +
> > +#define CDRAM_PCS0 2
> > +#define CDRAM_CONT BIT(7)
> > +#define CDRAM_BITS_EN BIT(6)
> > +#define CDRAM_QUAD_MODE BIT(8)
> > +#define CDRAM_RBIT_INPUT BIT(10)
> > +#define MSPI_SPE BIT(6)
> > +#define MSPI_CONT_AFTER_CMD BIT(7)
> > +
> > +/* Register fields */
> > +#define MSPI_SPCR0_MSB_BITS_8 0x00000020
> > +#define BSPI_RAF_CONTROL_START_MASK 0x00000001
> > +#define BSPI_RAF_STATUS_SESSION_BUSY_MASK 0x00000001
> > +#define BSPI_RAF_STATUS_FIFO_EMPTY_MASK 0x00000002
> > +#define BSPI_BITS_PER_PHASE_ADDR_MARK 0x00010000
> > +#define BSPI_BITS_PER_CYCLE_DATA_SHIFT 0
> > +#define BSPI_BITS_PER_CYCLE_ADDR_SHIFT 16
> > +#define BSPI_STRAP_OVERRIDE_DATA_QUAD_SHIFT 3
> > +#define BSPI_STRAP_OVERRIDE_DATA_DUAL_SHIFT 1
> > +#define BSPI_STRAP_OVERRIDE_SHIFT 0
> > +
> > +/* MSPI registers */
> > +#define MSPI_SPCR0_LSB_REG 0x000
> > +#define MSPI_SPCR0_MSB_REG 0x004
> > +#define MSPI_SPCR1_LSB_REG 0x008
> > +#define MSPI_SPCR1_MSB_REG 0x00c
> > +#define MSPI_NEWQP_REG 0x010
> > +#define MSPI_ENDQP_REG 0x014
> > +#define MSPI_SPCR2_REG 0x018
> > +#define MSPI_STATUS_REG 0x020
> > +#define MSPI_CPTQP_REG 0x024
> > +#define MSPI_TXRAM_REG 0x040
> > +#define MSPI_RXRAM_REG 0x0c0
> > +#define MSPI_CDRAM_REG 0x140
> > +#define MSPI_WRITE_LOCK_REG 0x180
> > +#define MSPI_DISABLE_FLUSH_GEN_REG 0x184
> > +
> > +/* BSPI registers */
> > +#define BSPI_REVISION_ID_REG 0x000
> > +#define BSPI_SCRATCH_REG 0x004
> > +#define BSPI_MAST_N_BOOT_CTRL_REG 0x008
> > +#define BSPI_BUSY_STATUS_REG 0x00c
> > +#define BSPI_INTR_STATUS_REG 0x010
> > +#define BSPI_B0_STATUS_REG 0x014
> > +#define BSPI_B0_CTRL_REG 0x018
> > +#define BSPI_B1_STATUS_REG 0x01c
> > +#define BSPI_B1_CTRL_REG 0x020
> > +#define BSPI_STRAP_OVERRIDE_CTRL_REG 0x024
> > +#define BSPI_FLEX_MODE_ENABLE_REG 0x028
> > +#define BSPI_BITS_PER_CYCLE_REG 0x02C
> > +#define BSPI_BITS_PER_PHASE_REG 0x030
> > +#define BSPI_CMD_AND_MODE_BYTE_REG 0x034
> > +#define BSPI_FLASH_UPPER_ADDR_BYTE_REG 0x038
> > +#define BSPI_XOR_VALUE_REG 0x03C
> > +#define BSPI_XOR_ENABLE_REG 0x040
> > +#define BSPI_PIO_MODE_ENABLE_REG 0x044
> > +#define BSPI_PIO_IODIR_REG 0x048
> > +#define BSPI_PIO_DATA_REG 0x04C
> > +
> > +/* RAF registers */
> > +#define BSPI_RAF_START_ADDRESS_REG 0x00
> > +#define BSPI_RAF_NUM_WORDS_REG 0x04
> > +#define BSPI_RAF_CTRL_REG 0x08
> > +#define BSPI_RAF_FULLNESS_REG 0x0C
> > +#define BSPI_RAF_WATERMARK_REG 0x10
> > +#define BSPI_RAF_STATUS_REG 0x14
> > +#define BSPI_RAF_READ_DATA_REG 0x18
> > +#define BSPI_RAF_WORD_CNT_REG 0x1C
> > +#define BSPI_RAF_CURR_ADDR_REG 0x20
> > +
> > +#define XFER_DUAL BIT(30)
> > +#define XFER_QUAD BIT(31)
> > +
> > +#define FLASH_BIT BIT(0)
> > +#define MAST_N_BOOT_BIT BIT(0)
> > +#define FLEX_MODE_ENABLE_BIT BIT(0)
> > +#define WRITE_LOCK_BIT BIT(0)
> > +
> > +/* state */
> > +enum bcm_qspi_state {
> > + QSPI_STATE_DISABLED,
> > + QSPI_STATE_MSPI,
> > + QSPI_STATE_BSPI
> > +};
> > +
> > +/**
> > + * struct bcmspi_priv - qspi private structure
> > + *
> > + * @max_hz: device transfer speed
> > + * @spi_mode: spi mode (SPI_... flags)
> > + * @frequency: spi max frequency
> > + * @state: device state (MSPI/BSPI)
> > + * @bspi_addr: bspi read address
> > + * @mspi_16bit: mspi transfer mode
> > + * @use_bspi: flag to indicate BSPI use for read operation
> > + * @mspi: mspi registers block address
> > + * @bspi: bspi registers block address
> > + * @bspi_raf: bspi raf registers block address
> > + */
> > +struct bcmspi_priv {
> > + uint max_hz;
> > + uint spi_mode;
> > + s32 frequency;
> > + enum bcm_qspi_state state;
> > + u32 bspi_addr;
> > + int mspi_16bit;
> > + int mode_4byte;
> > + int use_bspi;
> > + void __iomem *mspi;
> > + void __iomem *bspi;
> > + void __iomem *bspi_raf;
> > +};
> > +
> > +static void bspi_flush_prefetch_buffers(struct bcmspi_priv *priv)
> > +{
> > + writel(0, priv->bspi + BSPI_B0_CTRL_REG);
> > + writel(0, priv->bspi + BSPI_B1_CTRL_REG);
> > + writel(FLASH_BIT, priv->bspi + BSPI_B0_CTRL_REG);
> > + writel(FLASH_BIT, priv->bspi + BSPI_B1_CTRL_REG);
> > +}
> > +
> > +static int bcmspi_enable_bspi(struct bcmspi_priv *priv)
> > +{
> > + if (priv->state == QSPI_STATE_BSPI)
> > + return 0;
> > +
> > + /* Disable write lock */
> > + writel(0, priv->mspi + MSPI_WRITE_LOCK_REG);
> > + /* Flush prefetch buffers */
> > + bspi_flush_prefetch_buffers(priv);
> > + /* Switch to BSPI */
> > + writel(0, priv->bspi + BSPI_MAST_N_BOOT_CTRL_REG);
> > + /* Update state */
> > + priv->state = QSPI_STATE_BSPI;
> > +
> > + return 0;
> > +}
> > +
> > +static int bcmspi_disable_bspi(struct bcmspi_priv *priv)
> > +{
> > + if (priv->state == QSPI_STATE_MSPI)
> > + return 0;
> > +
> > + /* Switch to MSPI if not yet */
> > + if ((readl(priv->bspi + BSPI_MAST_N_BOOT_CTRL_REG) & 1) == 0) {
> > + ulong start = get_timer(0);
> > +
> > + while (get_timer(start) <
> > + QSPI_WAIT_TIMEOUT_MS * CONFIG_SYS_HZ / 1000) {
> > + if ((readl(priv->bspi + BSPI_BUSY_STATUS_REG) &
> > 1)
> > + == 0) {
> > + writel(MAST_N_BOOT_BIT, priv->bspi +
> > + BSPI_MAST_N_BOOT_CTRL_REG);
> > + udelay(1);
> > + break;
> > + }
> > + udelay(1);
> > + }
> > + if ((readl(priv->bspi + BSPI_MAST_N_BOOT_CTRL_REG) & 1)
> > != 1)
> > + return -1;
> > + }
> > +
> > + /* Update state */
> > + priv->state = QSPI_STATE_MSPI;
> > +
> > + return 0;
> > +}
> > +
> > +static void bspi_read_via_raf(struct bcmspi_priv *priv, u8 *rx, uint
> > bytes)
> > +{
> > + u32 status;
> > + uint words;
> > + int aligned;
> > +
> > + /* Flush data from the previous session (unlikely) */
> > + for (;;) {
> > + status = readl(priv->bspi_raf + BSPI_RAF_STATUS_REG);
> > + if (!(status & BSPI_RAF_STATUS_FIFO_EMPTY_MASK)) {
> > + readl(priv->bspi_raf + BSPI_RAF_READ_DATA_REG);
> > + continue;
> > + }
> > + if (!(status & BSPI_RAF_STATUS_SESSION_BUSY_MASK))
> > + break;
> > + }
> > +
> > + /* Transfer is in words */
> > + words = (bytes + 3) / 4;
> > +
> > + /* Setup hardware */
> > + if (priv->mode_4byte) {
> > + u32 val = priv->bspi_addr & 0xFF000000;
> > +
> > + if (val != readl(priv->bspi +
> BSPI_FLASH_UPPER_ADDR_BYTE_REG)) {
> > + writel(val,
> > + priv->bspi +
> > BSPI_FLASH_UPPER_ADDR_BYTE_REG);
> > + bspi_flush_prefetch_buffers(priv);
> > + }
> > + }
> > + writel(priv->bspi_addr & 0x00FFFFFF,
> > + priv->bspi_raf + BSPI_RAF_START_ADDRESS_REG);
> > + writel(words, priv->bspi_raf + BSPI_RAF_NUM_WORDS_REG);
> > + writel(0, priv->bspi_raf + BSPI_RAF_WATERMARK_REG);
> > +
> > + /* Kick off */
> > + writel(BSPI_RAF_CONTROL_START_MASK, priv->bspi_raf +
> BSPI_RAF_CTRL_REG);
> > +
> > + /* Reading the data */
> > + aligned = DWORD_ALIGNED(rx);
> > + while (bytes) {
> > + status = readl(priv->bspi_raf + BSPI_RAF_STATUS_REG);
> > + if (!(status & BSPI_RAF_STATUS_FIFO_EMPTY_MASK)) {
> > + u32 data = le32_to_cpu(readl(priv->bspi_raf +
> > +
> > BSPI_RAF_READ_DATA_REG));
> > +
> > + /* Check if we can use the whole word */
> > + if (aligned && bytes >= 4) {
> > + /*
> > + * RAF is LE only,
> > + * convert data to host endianness
> > + */
> > + *(u32 *)rx = le32_to_cpu(data);
> > + rx += 4;
> > + bytes -= 4;
> > + } else {
> > + uint chunk = min(bytes, 4U);
> > +
> > + /* Read out bytes one by one */
> > + while (chunk) {
> > + *rx++ = (u8)data;
> > + data >>= 8;
> > + chunk--;
> > + bytes--;
> > + }
> > + }
> > +
> > + continue;
> > + }
> > + if (!(status & BSPI_RAF_STATUS_SESSION_BUSY_MASK)) {
> > + /* FIFO is empty and the session is done */
> > + break;
> > + }
> > + }
> > +}
> > +
> > +static int bspi_read(struct bcmspi_priv *priv, const u8 *tx, u8 *rx,
> > + uint bytes, ulong flags)
> > +{
> > + int idx = priv->mode_4byte ? 2 : 1;
> > + /* Check the address */
> > + if (flags & SPI_XFER_BEGIN) {
> > + u32 addr;
> > +
> > + /* Drop if the first transfer doesn't contain full
> > address */
> > + if (bytes < idx + 3 + 1)
> > + return -1;
> > +
> > + /* Flash offset - lower 24 bits */
> > + addr = (tx[idx] << 16) | (tx[idx + 1] << 8) | tx[idx +
> > 2];
> > +
> > + /* Flash offset - upper 8 bits */
> > + if (priv->mode_4byte)
> > + addr |= tx[1] << 24;
> > +
> > + /* Remaining length for data (excluding one dummy cycle)
> > */
> > + bytes -= idx + 3 + 1;
> > + if (rx)
> > + rx += idx + 3 + 1;
> > +
> > + /* non-aligned transfers are handled by MSPI */
> > + if (!DWORD_ALIGNED(addr))
> > + return -1;
> > +
> > + bcmspi_enable_bspi(priv);
> > + /* Record BSPI status */
> > + priv->bspi_addr = addr;
> > + }
> > +
> > + /* Transfer data if any */
> > + while (bytes && rx) {
> > + /* Special handing since RAF cannot go across 16MB
> > boundary */
> > + uint trans = bytes;
> > +
> > + /*
> > + * Divide into multiple transfers if it goes
> > + * across the boundary
> > + */
> > + if (priv->mode_4byte &&
> > + (priv->bspi_addr >> 24) !=
> > + ((priv->bspi_addr + bytes) >> 24)) {
> > + /*
> > + * Limit this transfer to not go beyond
> > + * 16MB boundary
> > + */
> > + trans = 0x1000000 - (priv->bspi_addr &
> > 0xFFFFFF);
> > + }
> > + bspi_read_via_raf(priv, rx, trans);
> > + priv->bspi_addr += trans;
> > + rx += trans;
> > + bytes -= trans;
> > + }
> > +
> > + /* Flush prefetch buffers at the end */
> > + if (flags & SPI_XFER_END)
> > + bspi_flush_prefetch_buffers(priv);
> > +
> > + return 0;
> > +}
> > +
> > +static int bspi_xfer(struct bcmspi_priv *priv, const u8 *tx, u8 *rx,
> > + uint bytes, ulong flags)
> > +{
> > + /* Check if we can make use of BSPI */
> > + if (flags & SPI_XFER_BEGIN) {
> > + if (bytes) {
> > + if (bspi_read(priv, tx, rx, bytes, flags) == 0)
> > + return 0;
> > + }
> > + } else if (priv->state == QSPI_STATE_BSPI) {
> > + if (bspi_read(priv, tx, rx, bytes, flags) == 0)
> > + return 0;
> > + }
> > +
> > + /* continue in mspi mode */
> > + return 1;
> > +}
> > +
> > +static int mspi_xfer(struct bcmspi_priv *priv, uint bytes,
> > + const u8 *tx, u8 *rx, ulong flags)
> > +{
> > + u32 cdr = CDRAM_PCS0;
> > +
> > + if (flags & XFER_QUAD) {
> > + cdr |= CDRAM_QUAD_MODE;
> > +
> > + if (!tx)
> > + cdr |= CDRAM_RBIT_INPUT;
> > + }
> > +
> > + if (bytes & 1) {
> > + /* Use 8-bit queue for odd-bytes transfer */
> > + if (priv->mspi_16bit) {
> > + setbits_le32(priv->mspi + MSPI_SPCR0_MSB_REG,
> > + MSPI_SPCR0_MSB_BITS_8);
> > + priv->mspi_16bit = 0;
> > + }
> > + } else {
> > + /* Use 16-bit queue for even-bytes transfer */
> > + if (!priv->mspi_16bit) {
> > + clrbits_le32(priv->mspi + MSPI_SPCR0_MSB_REG,
> > + MSPI_SPCR0_MSB_BITS_8);
> > + priv->mspi_16bit = 1;
> > + }
> > + }
> > +
> > + while (bytes) {
> > + uint chunk;
> > + uint queues;
> > + ulong start;
> > + uint i;
> > +
> > + /* Separate code for 16bit and 8bit transfers for
> > performance */
> > + if (priv->mspi_16bit) {
> > + /* Determine how many bytes to process this time
> > */
> > + chunk = min(bytes, NUM_CDRAM * 2);
> > + queues = (chunk - 1) / 2 + 1;
> > + bytes -= chunk;
> > +
> > + /* Fill CDRAMs */
> > + for (i = 0; i < queues; i++)
> > + writel(cdr | CDRAM_CONT | CDRAM_BITS_EN,
> > + priv->mspi + MSPI_CDRAM_REG + (i
> > << 2));
> > +
> > + /* Fill TXRAMs */
> > + for (i = 0; i < chunk; i++)
> > + writel(tx ? tx[i] : 0xff,
> > + priv->mspi + MSPI_TXRAM_REG + (i
> > << 2));
> > + } else {
> > + /* Determine how many bytes to process this time
> > */
> > + chunk = min(bytes, NUM_CDRAM);
> > + queues = chunk;
> > + bytes -= chunk;
> > +
> > + /* Fill CDRAMs and TXRAMS */
> > + for (i = 0; i < chunk; i++) {
> > + writel(cdr | CDRAM_CONT,
> > + priv->mspi + MSPI_CDRAM_REG + (i
> > << 2));
> > + writel(tx ? tx[i] : 0xff,
> > + priv->mspi + MSPI_TXRAM_REG + (i
> > << 3));
> > + }
> > + }
> > +
> > + /* Setup queue pointers */
> > + writel(0, priv->mspi + MSPI_NEWQP_REG);
> > + writel(queues - 1, priv->mspi + MSPI_ENDQP_REG);
> > +
> > + /* Deassert CS if requested and it's the last transfer
> > */
> > + if (bytes == 0 && (flags & SPI_XFER_END))
> > + clrbits_le32(priv->mspi + MSPI_CDRAM_REG +
> > + ((queues - 1) << 2), CDRAM_CONT);
> > +
> > + /* Kick off */
> > + writel(0, priv->mspi + MSPI_STATUS_REG);
> > + if (bytes == 0 && (flags & SPI_XFER_END))
> > + writel(MSPI_SPE, priv->mspi + MSPI_SPCR2_REG);
> > + else
> > + writel(MSPI_SPE | MSPI_CONT_AFTER_CMD,
> > + priv->mspi + MSPI_SPCR2_REG);
> > +
> > + /* Wait for completion */
> > + start = get_timer(0);
> > + while (get_timer(start) <
> > + QSPI_WAIT_TIMEOUT_MS * CONFIG_SYS_HZ / 1000) {
> > + if (readl(priv->mspi + MSPI_STATUS_REG) & 1)
> > + break;
> > + }
> > + if ((readl(priv->mspi + MSPI_STATUS_REG) & 1) == 0)
> > + return -1;
> > +
> > + /* Read data out */
> > + if (rx) {
> > + if (priv->mspi_16bit) {
> > + for (i = 0; i < chunk; i++) {
> > + rx[i] = readl(priv->mspi +
> > + MSPI_RXRAM_REG +
> > + (i << 2)) & 0xff;
> > + }
> > + } else {
> > + for (i = 0; i < chunk; i++) {
> > + rx[i] = readl(priv->mspi +
> > + MSPI_RXRAM_REG +
> > + (((i << 1) + 1) <<
> > 2))
> > + & 0xff;
> > + }
> > + }
> > + }
> > +
> > + /* Advance pointers */
> > + if (tx)
> > + tx += chunk;
> > + if (rx)
> > + rx += chunk;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int iproc_qspi_set_speed(struct udevice *bus, uint speed)
> > +{
> > + struct bcmspi_priv *priv = dev_get_priv(bus);
> > + uint spbr;
> > +
> > + priv->max_hz = speed;
> > +
> > + /* MSPI: SCK configuration */
> > + spbr = (QSPI_AXI_CLK - 1) / (2 * priv->max_hz) + 1;
> > + writel(max(min(spbr, SPBR_MAX), SPBR_MIN),
> > + priv->mspi + MSPI_SPCR0_LSB_REG);
> > +
> > + return 0;
> > +}
> > +
> > +static int iproc_qspi_set_mode(struct udevice *bus, uint mode)
> > +{
> > + struct bcmspi_priv *priv = dev_get_priv(bus);
> > + u32 data_lanes;
> > +
> > + priv->spi_mode = mode;
> > +
> > + if (mode & SPI_RX_QUAD)
> > + data_lanes = 4;
> > + else if (mode & SPI_RX_DUAL)
> > + data_lanes = 2;
> > + else
> > + data_lanes = 1;
> > +
> > + if (data_lanes != 1) {
> > + /* BSPI: configure for dual/quad mode */
> > + writel(0, priv->bspi + BSPI_BITS_PER_CYCLE_REG);
> > + writel(0, priv->bspi + BSPI_FLEX_MODE_ENABLE_REG);
> > + /* Dummy cycles */
> > + setbits_le32(priv->bspi + BSPI_BITS_PER_PHASE_REG,
> > + IPROC_BSPI_READ_DUMMY_CYCLES);
> > + /* Override the strap settings */
> > + setbits_le32(priv->bspi + BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 << BSPI_STRAP_OVERRIDE_SHIFT);
> > + /*
> > + * Configure following based on QUAD/DUAL mode
> > + * - data_quad or data_dual_n_sgl
> > + * - data_bpc select
> > + * - bspi_cmd_byte
> > + */
> > + if (data_lanes == 4) {
> > + setbits_le32(priv->bspi +
> > BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 <<
> > BSPI_STRAP_OVERRIDE_DATA_QUAD_SHIFT);
> > + clrbits_le32(priv->bspi +
> > BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 <<
> > BSPI_STRAP_OVERRIDE_DATA_DUAL_SHIFT);
> > + setbits_le32(priv->bspi +
> > BSPI_BITS_PER_CYCLE_REG,
> > + 2 <<
> > BSPI_BITS_PER_CYCLE_DATA_SHIFT);
> > + writel(IPROC_BSPI_READ_CMD4,
> > + priv->bspi + BSPI_CMD_AND_MODE_BYTE_REG);
> > + } else if (data_lanes == 2) {
> > + clrbits_le32(priv->bspi +
> > BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 <<
> > BSPI_STRAP_OVERRIDE_DATA_QUAD_SHIFT);
> > + setbits_le32(priv->bspi +
> > BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 <<
> > BSPI_STRAP_OVERRIDE_DATA_DUAL_SHIFT);
> > + setbits_le32(priv->bspi +
> > BSPI_BITS_PER_CYCLE_REG,
> > + 1 <<
> > BSPI_BITS_PER_CYCLE_DATA_SHIFT);
> > + writel(IPROC_BSPI_READ_CMD2,
> > + priv->bspi + BSPI_CMD_AND_MODE_BYTE_REG);
> > + }
> > + /* Enable flex mode to take effect */
> > + writel(FLEX_MODE_ENABLE_BIT, priv->bspi +
> > + BSPI_FLEX_MODE_ENABLE_REG);
> > + } else {
> > + /* configure BSPI for single mode */
> > + writel(0, priv->bspi + BSPI_FLEX_MODE_ENABLE_REG);
> > + writel(0, priv->bspi + BSPI_BITS_PER_CYCLE_REG);
> > + /* Dummy cycles */
> > + setbits_le32(priv->bspi + BSPI_BITS_PER_PHASE_REG,
> > + IPROC_BSPI_READ_DUMMY_CYCLES);
> > + /* clear strap override, data_dual_n_sgl and data_quad
> > bits */
> > + clrbits_le32(priv->bspi + BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 << BSPI_STRAP_OVERRIDE_SHIFT);
> > + clrbits_le32(priv->bspi + BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 << BSPI_STRAP_OVERRIDE_DATA_QUAD_SHIFT);
> > + clrbits_le32(priv->bspi + BSPI_STRAP_OVERRIDE_CTRL_REG,
> > + 1 << BSPI_STRAP_OVERRIDE_DATA_DUAL_SHIFT);
> > + writel(IPROC_BSPI_READ_CMD,
> > + priv->bspi + BSPI_CMD_AND_MODE_BYTE_REG);
> > + }
> > +
> > + /*
> > + * MSPI: Mode configuration (8 bits by default)
> > + * MSPI supports only single mode.
> > + */
> > + priv->mspi_16bit = 0;
> > + writel(0x80 | /* Master */
> > + (8 << 2) | /* 8 bits per word */
> > + (priv->spi_mode & 3), /* mode: CPOL / CPHA */
> > + priv->mspi + MSPI_SPCR0_MSB_REG);
> > +
> > + return 0;
> > +}
> > +
> > +static int iproc_qspi_claim_bus(struct udevice *dev)
> > +{
> > + /* nothing to do */
> > + return 0;
> > +}
> > +
> > +static int iproc_qspi_release_bus(struct udevice *dev)
> > +{
> > + struct udevice *bus = dev->parent;
> > + struct bcmspi_priv *priv = dev_get_priv(bus);
> > +
> > + /* Make sure no operation is in progress */
> > + writel(0, priv->mspi + MSPI_SPCR2_REG);
> > + udelay(1);
> > +
> > + return 0;
> > +}
> > +
> > +static int iproc_qspi_xfer(struct udevice *dev, uint bitlen,
> > + const void *dout, void *din, ulong flags)
> > +{
> > + struct udevice *bus = dev->parent;
> > + struct bcmspi_priv *priv = dev_get_priv(bus);
> > + const u8 *tx = dout;
> > + u8 *rx = din;
> > + uint bytes = bitlen / 8;
> > + int ret = 0;
> > +
> > + /* we can only do 8 bit transfers */
> > + if (bitlen % 8)
> > + return -1;
> > +
> > + if (priv->use_bspi) {
> > + ret = bspi_xfer(priv, tx, rx, bytes, flags);
> > + if (ret <= 0)
> > + return ret;
> > + }
> > +
> > + /* MSPI: Enable write lock at the beginning */
> > + if (flags & SPI_XFER_BEGIN) {
> > + /* Switch to MSPI if not yet */
> > + if (bcmspi_disable_bspi(priv) != 0)
> > + return -1;
> > +
> > + writel(WRITE_LOCK_BIT, priv->mspi +
> > MSPI_WRITE_LOCK_REG);
> > + }
> > +
> > + /* MSPI: Transfer it */
> > + if (bytes)
> > + ret = mspi_xfer(priv, bytes, tx, rx, flags);
> > +
> > + /* MSPI: Disable write lock if it's done */
> > + if (flags & SPI_XFER_END) {
> > + writel(0, priv->mspi + MSPI_WRITE_LOCK_REG);
> > + /* Switch back to BSPI */
> > + if (priv->use_bspi)
> > + writel(0, priv->bspi +
> > BSPI_MAST_N_BOOT_CTRL_REG);
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static int iproc_qspi_ofdata_to_platdata(struct udevice *bus)
> > +{
> > + struct bcmspi_priv *priv = dev_get_priv(bus);
> > + ofnode subnode;
> > +
> > + priv->bspi = (void __iomem *)dev_read_addr_name(bus, "bspi");
> > + if (IS_ERR(priv->bspi)) {
> > + debug("%s: Failed to get bspi base address\n",
> > __func__);
> > + return PTR_ERR(priv->bspi);
> > + }
> > +
> > + priv->bspi_raf = (void __iomem *)dev_read_addr_name(bus,
> "bspi_raf");
> > + if (IS_ERR(priv->bspi_raf)) {
> > + debug("%s: Failed to get bspi_raf base address\n",
> > __func__);
> > + return PTR_ERR(priv->bspi_raf);
> > + }
> > +
> > + priv->mspi = (void __iomem *)dev_read_addr_name(bus, "mspi");
> > + if (IS_ERR(priv->mspi)) {
> > + debug("%s: Failed to get mspi base address\n",
> > __func__);
> > + return PTR_ERR(priv->mspi);
> > + }
> > +
> > + subnode = dev_read_first_subnode(bus);
> > + if (ofnode_valid(subnode))
> > + priv->frequency = ofnode_read_u32_default(subnode,
> > +
> > "spi-max-frequency",
> > +
> > QSPI_DEF_SCK_FREQ);
> > + else
> > + priv->frequency = QSPI_DEF_SCK_FREQ;
> > +
> > + priv->use_bspi = dev_read_u32_default(bus, "use-bspi", 0);
> > +
> > + return 0;
> > +}
> > +
> > +static int iproc_qspi_probe(struct udevice *bus)
> > +{
> > + struct bcmspi_priv *priv = dev_get_priv(bus);
> > +
> > + priv->mode_4byte = 0;
> > + /* MSPI: Basic hardware initialization */
> > + writel(0, priv->mspi + MSPI_SPCR1_LSB_REG);
> > + writel(0, priv->mspi + MSPI_SPCR1_MSB_REG);
> > + writel(0, priv->mspi + MSPI_NEWQP_REG);
> > + writel(0, priv->mspi + MSPI_ENDQP_REG);
> > + writel(0, priv->mspi + MSPI_SPCR2_REG);
> > +
> > + if (priv->use_bspi) {
> > + bcmspi_enable_bspi(priv);
> > + } else {
> > + if (bcmspi_disable_bspi(priv)) {
> > + printf("Failed to set in MSPI mode\n");
> > + return -1;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct dm_spi_ops iproc_qspi_ops = {
> > + .claim_bus = iproc_qspi_claim_bus,
> > + .release_bus = iproc_qspi_release_bus,
> > + .xfer = iproc_qspi_xfer,
> > + .set_speed = iproc_qspi_set_speed,
> > + .set_mode = iproc_qspi_set_mode,
> > +};
> > +
> > +static const struct udevice_id iproc_qspi_ids[] = {
> > + { .compatible = "brcm,iproc-qspi" },
> > + { }
> > +};
> > +
> > +U_BOOT_DRIVER(iproc_qspi) = {
> > + .name = "iproc_qspi",
> > + .id = UCLASS_SPI,
> > + .of_match = iproc_qspi_ids,
> > + .ops = &iproc_qspi_ops,
> > + .of_to_plat = iproc_qspi_ofdata_to_platdata,
> > + .priv_auto = sizeof(struct bcmspi_priv),
> > + .probe = iproc_qspi_probe,
> > +};
> > diff --git a/drivers/spi/iproc_qspi.h b/drivers/spi/iproc_qspi.h
> > new file mode 100644
> > index 000000000000..6f1218c959ce
> > --- /dev/null
> > +++ b/drivers/spi/iproc_qspi.h
> > @@ -0,0 +1,20 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +/*
> > + * Copyright 2020-2021 Broadcom
> > + */
> > +
> > +#include <spi.h>
> > +
> > +#ifndef _IPROC_QSPI_H_
> > +#define _IPROC_QSPI_H_
> > +
> > +/*SPI configuration enable*/
> > +#define IPROC_QSPI_BUS 0
> > +#define IPROC_QSPI_CS 0
> > +
>
> Look like the previous comments are not resolved still.
>
> > +#define IPROC_BSPI_READ_CMD 0x0b
>
> SPINOR_OP_READ_FAST
>
> > +#define IPROC_BSPI_READ_CMD2 0x3b
>
> SPINOR_OP_READ_1_1_2
>
> > +#define IPROC_BSPI_READ_CMD4 0x6b
>
> SPINOR_OP_READ_1_1_4
>
> > +#define IPROC_BSPI_READ_DUMMY_CYCLES 0x08
>
> Flash dummy cycles.
>
> If the controller purely a flash specific, add it in mtd side.
> drivers/spi is for spi controller drivers.
>
> Jagan.
Hi Jagan,
We will move it to mtd side as requested.
Thank you very much for your review,
Roman
--
This electronic communication and the information and any files transmitted
with it, or attached to it, are confidential and are intended solely for
the use of the individual or entity to whom it is addressed and may contain
information that is confidential, legally privileged, protected by privacy
laws, or otherwise restricted from disclosure to anyone else. If you are
not the intended recipient or the person responsible for delivering the
e-mail to the intended recipient, you are hereby notified that any use,
copying, distributing, dissemination, forwarding, printing, or copying of
this e-mail is strictly prohibited. If you received this e-mail in error,
please return the e-mail to the sender, delete it from your computer, and
destroy any printed copy of it.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 4206 bytes
Desc: S/MIME Cryptographic Signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20211025/5d78c147/attachment.bin>
More information about the U-Boot
mailing list